Tibial fixation comparison of semitendinosus-bone composite allografts fixed with bioabsorbable screws and bone-patella tendon-bone grafts fixed with titanium screws

Tibial fixation remains the weak link of ACL reconstruction over the first 8–12 weeks postoperatively. This study compared the biomechanical properties of tibial fixation for a bone-patellar tendon-bone (BPTB) graft and a novel semitendinosus-bone composite (SBC) allograft with mixed cortical-cancellous bone dowels at each end. Seven paired, fresh frozen cadaveric knees (20–45 years) were stripped of all soft tissue attachments and randomly assigned to receive either the BPTB graft or SBC allograft. Grafts were placed into tibial tunnels via a standard protocol and secured with either a 10 mm×28 mm bioabsorbable (SBC) or titanium (BPTB) screw. Grafts were cycled ten times in a servo hydraulic device from 10–50 N prior to pull to failure testing at a rate of 20 mm/min with the force vector aligned with the tibial tunnel ("worst case scenario"). Wilcoxon Signed Rank Tests were used to evaluate biomechanical differences between graft types (p<0.05). Tibial bone mineral density and interference screw insertion torque were statistically equivalent between graft types. The mode of failure for all constructs was direct screw and graft construct pullout from the tibial tunnel. Significant differences were not observed between graft types for maximum load at failure strength (BPTB=620.8±209 N vs. SBC=601.2±140 N, p=0.74) or stiffness (BPTB=69.8 N/mm±29 N/mm vs SBC=47.1±31.6 N/mm, p=0.24). The SBC allograft yielded significantly more displacement prior to failure than the BPTB graft (15.1±4.9 mm vs 9.2±1.3 mm, p=0.04). Increased construct displacement appeared to be due to fixation failure, with some evidence of graft tissue tearing around the sutures: Bioabsorbable screw (10×28 mm) fixation of the SBC allograft produced unacceptable displacement levels during testing. Further study is recommended using a titanium interference screw or a longer bioabsorbable screw for SBC graft fixation under cyclic loading conditions.Arthrex Inc., Naples, FL, USA sponsored this study     

Biomechanical evaluation of a new cross-pin technique for the fixation of different sized bone–patellar tendon–bone grafts

To overcome the disadvantages of interference-screw fixation of bone–patellar tendon–bone (BPTB) grafts, new fixation techniques for anterior cruciate ligament (ACL) grafts using biodegradable pins have been developed. The hypothesis of the present study was that cross-pin fixation techniques provide a primary stability that is comparable to that of interference screws. A biomechanical in vitro study was discussed. Human BPTB grafts of 8, 9 and 10 mm diameter were fixed in bovine knees with biodegradable cross pins (diameter: 2.0, 2.7 or 3.2 mm) or biodegradable interference screws. Stiffness and ultimate load were evaluated. For 9 and 10 mm BPTB grafts, no statistically significant difference in maximum load and stiffness was found between the four fixation techniques tested. For 8 mm bone blocks the maximum load of the 3.2 mm pins (274.2 N) was significantly lower than for the 2.0 mm pins (479.8 N) and the interference screws (504.0 N). Predominant failure mode in this group was bone-block fracture. Thicker grafts (9 and 10 mm) fixed with the 2.0 mm pins predominantly failed by implant fracture. Femoral fixation of 8, 9 and 10 mm BPTB grafts using cross pins leads to biomechanical properties that are comparable to biodegradable interference screws when tested by a single-cycle load to failure. Cross pins provide a rigid fixation for 9 and 10 mm BPTB grafts.     

Autologous patellar tendon and quadrupled hamstring grafts in anterior cruciate ligament reconstruction: a prospective randomized multicenter review of different fixation methods

ACL reconstruction with bone patellar tendon bone (BPTB) grafts has been shown to produce dependable results. Recently, reconstructions with double-looped semitendinosus gracilis (DLSG) grafts have become common. The prevailing opinion is that ACL reconstruction with patellar tendon graft produces a more stable knee with more anterior knee pain than DLSG grafts, while the functional results and knee scores are similar. The present study evaluates BPTB grafts fixed with metallic interference screws and DLSG grafts fixed with Bone Mulch Screw on the femur and WasherLoc fixation on the tibia. All else being the same, there is no difference in the outcome between the two grafts and fixation methods. This is a prospective randomized multicenter study. A total of 115 patients with isolated ACL ruptures were randomized to either reconstruction with BPTB grafts fixed with metal interference screws (58 patients) or DLSG grafts (57 patients) fixed with Bone Mulch Screws and WasherLoc Screws. Follow-up was at one and two years; the latter by an independent observer. At two years, one ACL revision had been performed in each group. Eight patients in the DLSG group and one in the BPTB group underwent meniscus surgery in the follow-up period (P = 0.014). Mean Lysholm score at the two year follow-up was 91 (SD ± 10.3) in the DLSG group and also 91 (SD ± 10.2) in the BPTB group. Mean KT-1000 at two years was 1.5 mm in the BPTB group and 1.8 mm in the DLSG group (n.s.). At two years, four patients in the BPTB group and three in the DLSG group had a Lachman test grade 2 or 3 (n.s.). More patients in the BPTB group had pain at the lower pole of the patella (P = 0.04). Peak flexion torque and total flexion work were lower in the DLSG group at one year (P = 0.003 and P = 0.000) and total flexion work also at two years (P = 0.05). BPTB ACL reconstruction fixed with interference screws and DLSG fixed with Bone Mulch Screws on the femur and WasherLoc Screws on the tibia produce satisfactory and nearly identical outcomes. Among our patients in the DLSG group, flexion strength was lower, and more patients underwent meniscus surgery in the follow-up period. The BPTB group has more anterior knee pain.     

Metallic versus bioabsorbable interference screw for fixation of bone-patellar tendon-bone autograft in arthroscopic anterior cruciate ligament reconstruction A preliminary report

We retrospectively compared the clinical outcome and the radiographic incorporation of the bone blocks between two groups of patients undergoing anterior cruciate ligament reconstruction using either metallic or bioabsorbable interference screws for fixation of the bone-patellar tendon-bone autograft. Sixty-nine patients (44 male and 25 female) were available for follow-up. There were 31 patients with a mean age of 33 years (range 16–59 years) in group I (bioabsorbable interference screw fixation) and 38 patients with a mean age of 32 years (range 18–58) in group II (metallic screw fixation). The mean follow-up was 9.6 months after surgery in group I (range 6–17 months) and 20.5 months in group II (range 6–32 months). At follow-up, the IKDC scores were comparable between the two groups, and there was no statistically significant difference for the Lysholm (P = 0.925) and Tegner (P = 0.197) scores. The KT-2000 tests showed a statistically insignificant mean side-to-side difference of 2.0 mm (+2.2 mm SD) in group I and 2.2 mm (+2.4 mm SD) in group II (P = 0.741). At follow-up, all patients showed osseous incorporation of the bone block autografts within the femoral and tibial bone tunnels with no osteolytic changes.     

Bioabsorbable screw divergence angle,not tunnel preparation method influences soft tissue tendon graft-bone tunnel fixation in healthy bone

Bone tunnel fixation of a soft tissue tendon graft is the weak link immediately following ACL reconstruction. This biomechanical study evaluated the influence of extraction drilled or step dilated bone tunnels and bioabsorbable screw divergence on soft tissue tendon graft fixation. From an initial group of 50 available specimens, similar apparent bone mineral density porcine tibiae (1.2 ± 0.24 g/cm²) were divided into two groups of ten specimens each. Group 1 (extraction drilled) received 9 mm diameter tunnels. Group 2 (step dilated) received 7 mm diameter tunnels that were dilated to 9 mm. Grafts were secured in tunnels using 10 mm diameter, 35 mm long tapered screws. After high resolution CT scanning to evaluate screw divergence, constructs were pretensioned on a servo hydraulic device between 10 and 50 N for 10 cycles, and isometric pretensioned at 50 N for 1 min, prior to 500 sub-maximal loading cycles (50–200 N) and load to failure testing at 20 mm/min. Wilcoxon Signed Rank tests and Mann–Whitney U-tests were used to evaluate group differences. Coefficient of determination values (r ²) were calculated to further delineate statistically significant relationships. Tunnel preparation method did not display statistically significant effects on insertion torque, displacement during cyclic testing, relative stiffness during cyclic testing, load at failure, stiffness during load to failure testing or displacement during load to failure testing. Screw divergence < 15° produced lower displacement and greater relative stiffness during cyclic testing and greater load at failure and stiffness during load to failure testing. Screw divergence angle displayed moderate relationships with construct displacement during cyclic testing (r ² = 0.54), stiffness during load to failure testing (r ² = 0.60), and load at failure (r ² = 0.41). Tunnel dilation does not enhance soft tissue tendon graft fixation strength in healthy bone. Bioabsorbable screw divergence of ≥ 15° significantly reduces soft tissue tendon graft-bone tunnel fixation.     

Tunnel expansion following anterior cruciate ligament reconstruction: a comparison of hamstring and patellar tendon autografts

Thirty patients having had anterior cruciate ligament (ACL) reconstruction with bone-patellar tendon-bone (BPTB) autograft and thirty patients having had ACL reconstruction with hamstring (HS) autograft were enrolled. All procedures were performed using an endoscopic technique with identical postoperative rehabilitation, such that the only variable was the type of graft and its fixation. Lateral and 45° posteroanterior (PA) weightbearing radiographs were performed in each patient at 6–12 (mean 9) months postoperatively in the HS group and 9–22 (mean 13) months postoperatively in the PT group. The sclerotic margins of the tunnel were measured at the widest dimension of the tunnel by a single observer and were compared with the initially drilled tunnel size after correction for radiographic magnification. For the BPTB group, all bone plugs appeared to be incorporated radiographically. On the femoral side, the bone plug was incorporated at the roof of the intercondylar notch, such that no tunnel measurement could be made. Well-defined sclerotic margins were always present at the tibial and femoral tunnels for the HS group and at the tibial tunnel for the BPTB group. The mean percentage increase in tunnel size in the PA view was 9.7% ± 14.7% for the BPTB tibial tunnel, 20.9% ± 13.4% for the HS tibial tunnel, and 30.2% ± 17.2% for the HS femoral tunnel. The mean percentage increase in tunnel size in the lateral view was 14.4% ± 16.1% for the BPTB tibial tunnel, 25.5% ± 16.7% for the HS tibial tunnel, and 28.1% ± 14.7% for the HS femoral tunnel. The difference in HS and BPTB tibial tunnel expansion on both the PA and lateral views was statistically significant (P = 0.003 and P = 0.01, respectively). Inter-observer variability was excellent with an intra-class correlation coefficient of 0.92. Tunnel expansion was significantly greater following ACL reconstruction using HS autografts than in those using BPTB autografts. The points of fixation for the HS grafts are at a greater distance from the normal insertion site and biomechanical point of action of the ACL than the points of fixation for BPTB grafts. We believe that this greater distance creates a potentially larger force moment during graft cycling which may lead to greater expansion of bone tunnels. Received: 17 March 1997 Accepted: 30 June 1997     

Initial fixation strength of bioabsorbable and titanium interference screws in anterior cruciate ligament reconstruction. Biomechanical evaluation by single cycle and cyclic loading

We evaluated the initial bone-patellar tendon-bone graft fixation strength of bioabsorbable as compared with titanium interference screws in anterior cruciate ligament reconstruction using matched pairs of porcine knees. Ten pairs underwent single-cycle failure loading at a rate of 50 mm/min, and 10 pairs underwent cyclic loading at half-hertz frequency. The cyclic loading started with 100 load cycles between 50 and 150 N. We then progressively increased loads in 50-N increments after each set of 100 cycles. After 100 cycles at 850 N, the specimens were loaded to failure at a rate of 50 mm/min. In the single-cycle failure loading test, the mean ultimate failure loads (+/-SD) for the bioabsorbable (837 +/- 260 N) and titanium interference screws (863 +/- 192 N) were not significantly different, nor were the mean yield loads or the stiffness of the fixation. In the cyclic loading test, the yield loads were 605 +/- 142 N and 585 +/- 103 N for the bioabsorbable and titanium interference screws, respectively (no significant difference). Although there was no significant difference in the ultimate failure load, more bone block fractures were found in the grafts fixed with a titanium interference screw. Bioabsorbable interference screw fixation thus seems to provide a reasonable alternative to titanium screws.     

Initial fixation strength of two bioabsorbable pins for the fixation of hamstring grafts compared to interference screw fixation: single cycle and cyclic loading

BACKGROUND: During the early postoperative period, the fixation of a hamstring graft to the bone tunnel is the primary factor in limiting rehabilitation. HYPOTHESIS: The initial fixation strength of a double cross pin fixation technique is comparable with the biodegradable interference screw fixation technique. STUDY DESIGN: Experimental laboratory study. METHODS: The authors examined the initial fixation strength of two 3.3-mm bioabsorbable pins compared to interference screws for hamstring grafts in bovine knees. RESULTS: Analysis of yield load, maximum load, and stiffness in the single-cycle loading test showed no statistically significant differences for cross pin and interference fixation (P <.05). For cross pins and interference screws, the mean displacement under 1000 cycles to 250 N was 5.07 ( +/- 1.9) mm and 4.81 ( +/- 2.5) mm, stiffness 252 ( +/- 78) N/mm and 289 ( +/- 148) N/mm. Only grafts fixed with cross pins survived 1000 cycles to 450 N. CONCLUSION: The initial fixation strength of the double cross pin technique is comparable to that of interference screw fixation with a stiffness comparable to that of the native ACL. Clinical Relevance: Hamstring graft fixation using two cross pins provides an alternative to bioabsorbable interference screw fixation.     

Analysis of initial fixation strength of press-fit fixation technique in anterior cruciate ligament reconstruction

We performed a controlled laboratory study to evaluate the initial fixation strength of press-fit technique. Forty porcine lower limbs were used and divided into four groups according to the method of fixation; group 1 (press-fit+1.4 mm), in which the diameter difference between the bone plug and the femoral tunnel was 1.4 mm; group 2 (press-fit+1.4 mm, 30 degrees), in which the diameter difference was the same with group 1, but the tensile loading axis was 30 degrees away from the long axis of the femoral tunnel; group 3 (titanium), in which a titanium interference screw was used for fixation; group 4 (bioabsorbable), in which a bioabsorbable interference screw was used for fixation. The graft in the press-fit group was harvested with a hollow oscillating saw with inner diameter of 9.4 mm to obtain consistent and completely circular shape of the bone plug. The femoral tunnel with diameter of 8 mm was drilled at the original ACL insertion. Following the bone plug insertion into the femoral tunnel and applying a preload of 20 N, the specimen underwent 500 loading cycles between 0 and 2 mm of displacement. Thereafter the specimen was loaded to failure. There was no fixation site failure during the cyclic loading test. Significant differences in the stiffness, linear load, or failure mode among the groups were not found. The average ultimate failure load of group 1 and group 2 were not significantly different from those of group 3 and group 4. The press-fit groups demonstrated sufficient fixation strength for the rehabilitation and interference screw groups. The completely circular shape of the bone plug and increased diameter difference between the bone plug and the femoral tunnel seemed to contribute to the strong fixation.     

A biomechanical comparison of initial fixation strength of 3 different methods of anterior cruciate ligament soft tissue graft tibial fixation: resistance to monotonic and cyclic loading

BACKGROUND: Tibial fixation of soft tissue grafts continues to be problematic in the early postoperative period after anterior cruciate ligament reconstruction. HYPOTHESIS: No differences exist for resistance to slippage of soft tissue grafts fixed with CentraLoc, Intrafix, or 35-mm bioabsorbable interference screws. STUDY DESIGN: Controlled laboratory study. METHODS: Bovine tibia and hoof extensor tendons were divided into 3 matched groups with 12 tibia and 12 extensor tendons in each group. Within each group, 6 specimens underwent monotonic loading to failure (1 mm/s), and 6 underwent cyclic loading (10,000 cycles, 125-325 N, 1 Hz). RESULTS: No statistically significant differences were noted in mean load to failure or stiffness. The mean load to failure (and stiffness) for the 3 types of fixation were as follows: bioabsorbable interference screw, 631.6 +/- 130.1 N (88.17 +/- 6.79 N/mm); Intrafix, 644.3 +/- 195.2 N (81.65 +/- 16.5 N/mm); and CentraLoc, 791.1 +/- 72.7 N (77.89 +/- 7.07 N/mm). The slippage rates under cyclic loading for the 3 types of fixation were bioabsorbable interference screw, 0.336 +/- 0.074 microm/cycle; Intrafix, 27.2 +/- 31.6 microm/cycle; and CentraLoc, 0.0355 +/- 0.0046 microm/cycle. In this model, CentraLoc proved statistically superior in resistance to cyclic loading compared with the bioabsorbable interference screw (P < .05) and Intrafix (P < .0001). The bioabsorbable interference screw proved statistically superior to Intrafix in resistance to cyclic loading (P < .05). CONCLUSIONS: In this bovine model, CentraLoc and bioabsorbable interference screws provided superior resistance to cyclic loading compared with Intrafix. CLINICAL RELEVANCE: CentraLoc and bioabsorbable interference screws showed superior resistance to cyclic loading, which may indicate an increased resistance to clinical failure.     

Mechanical evaluation of a soft tissue interference screw with a small diameter: significance of graft/bone tunnel cross-sectional area ratio

The purpose of this study is to evaluate the mechanical properties of a graft fixation using a small diameter soft tissue interference screw and analyze the factors affecting the fixation strength. Forty porcine knees were used. A bone tunnel, either 4.5 mm (n=40) or 5.0 mm (n=40) in diameter, was created in the bone block obtained from the proximal tibia or the distal femur. A patella–patellar tendon specimen with varied width was harvested, and the distal end of the patellar tendon was fixed within the bone tunnel using a small diameter soft tissue interference screw (4×15 mm). Then, the patella–patellar tendon-bone block complex was loaded until failure occurred and the maximum load was measured. As potential influential factors on the fixation strength, the insertion torque, bone mineral density of the bone block, and graft/tunnel cross-sectional area ratio (GTR) of each specimen were calculated. A significant correlation between the maximum failure load and the insertion torque was demonstrated. The quadratic regression analysis showed a statistically significant correlation between the failure load and the GTR. Optimal GTR for achieving high fixation strength was approximately 80%. When used in appropriate conditions, the mean failure load was 177 N for the 4.5 mm screw and 180 N for the 5 mm screw. The use of a small diameter interference screw for the fixation of a tendon graft to a bone is clinically feasible. Our research showed that the selection of appropriate fitting conditions is an important factor for optimizing the properties of the fixation.     

Biomechanical analysis of femoral tunnel pull-out angles for anterior cruciate ligament reconstruction with bioabsorbable and metal interference screws

BACKGROUND: Fixation strength of metal and bioabsorbable interference screws has not been evaluated while varying the anterior cruciate ligament graft tension angle. HYPOTHESIS: There is no difference in fixation strength between 2 types of interference screws for anterior cruciate ligament graft fixation while the graft tension angle is varied relative to the femoral tunnel. STUDY DESIGN: Controlled laboratory study. METHODS: Forty-eight anterior cruciate ligament reconstructions were performed using immature porcine femurs stripped of soft tissue and doubled-over porcine flexor digitorum profundus tendon grafts. Specimens were randomized to bioabsorbable or titanium interference screw fixation. Specimens were randomized to one of three pull angles (0 degrees , 30 degrees , 60 degrees ) representing loading at different knee flexion angles (n = 8/group). Reconstructed ligaments were tensioned to 10 N followed by 200 loading cycles between 10 and 150 N and a final failure test. Construct elongation (mm) at 100 and 200 cycles and failure load (N) were analyzed using a 2-way analysis of variance (P < .05). RESULTS: Screw material interacted significantly with graft tension angle, as the bioabsorbable screw specimens demonstrated significantly greater fixation strength when tensioned at greater angles. Specimens fixed with bioabsorbable screws showed significantly less elongation at both 100 and 200 cycles and significantly greater failure load compared with titanium screws. CONCLUSION: Bioabsorbable interference screws acutely have increased fixation strength compared with titanium interference screws for anterior cruciate ligament grafts loaded at greater tension angles. CLINICAL RELEVANCE: The strength of anterior cruciate ligament reconstruction fixation increases with increasing divergence between the tension angle and femoral tunnel, a condition seen when the knee approaches full extension.     

Effect of screw length on bioabsorbable interference screw fixation in a tibial bone tunnel

Initial tibial fixation strength is the weak link after anterior cruciate ligament reconstruction with a quadrupled hamstring tendon graft fixed with bioabsorbable interference screws. The purpose of this study was to determine the biomechanical differences between 28-mm and tapered 35-mm interference screws for tibial fixation of a soft tissue graft in 16 young cadaveric tibias. Failure mode, displacement before failure, and ultimate failure load were tested with a testing machine aligned with the tibial tunnel to simulate a worst-case scenario. The mode of failure was graft slippage past the screw in all but one of the specimens. The mean maximum load at failure of the 28-mm screw was 594.9 +/- 141.0 N, with mean displacement at failure of 10.97 +/- 2.20 mm. The mean maximum load at failure of the 35-mm screw was 824.9 +/- 124.3 N, with a mean displacement to failure of 14.38 +/- 2.15 mm. The 38% difference in mean maximal load at failure was significant. Important variables in hamstring tendon graft fixation within a bone tunnel include bone mineral density, dilatation, gap size, screw placement, and screw width and length. Attention to these variables will help to provide secure graft fixation during biologic incorporation throughout the rehabilitation period.     

Interference screws should be shorter than the hamstring tendon graft in the bone tunnel for best fixation

Purpose

Interference screw fixation of hamstring tendon grafts in bone has to overcome the challenges that tendons have a slippery surface and viscoelastically adapt under pressure. As the typical failure mode of the graft is to slip past the interference screw, it was hypothesized that the position and configuration of the graft end may be of influence on the fixation strength.

Methods

Different configurations of the graft ending and its effect to primary fixation with interference screws after viscoelastic adaptation were tested in six groups: I: graft and the screw inserted at the same depth, II/III: the graft overlaps the tip of the screw (interference screw of 28 and 19 mm in length, respectively), IV: strengthening of the graft ending with additional suture knots, V: Endopearl, respectively, and VI: effect of partial retraction of the screw after excessive insertion. In vitro tests were performed with fresh calf tendon grafts and interference screws in bone tunnels (fresh porcine distal femur) all of 8 mm in diameter.

Results

The relative position of the graft ending to the tip of the interference screw thereby was recognized as a significant factor on pullout forces. Further strengthening at the graft endings with additional suture knots or an Endopearl device could improve primary hold as well.

Conclusions

Better fixation strength is achieved if the tip of interference screw does not extend past the end of a tendon graft. Enforcement of the tendon end with sutures or an implant can further improve fixation.     

Optimal screw diameter for interference fixation in a bone tunnel: a porcine model

The study investigates the optimal interference screw dimensions required to secure a tendon graft in a bone tunnel. A standard 8 mm pig flexor-tendon graft was inserted into a standard open-ended 8 mm bone tunnel of a porcine distal femur and secured using either 7 mm, 8 mm or 9 mm diameter metal interference screws (Arthrex Inc, Naples, FL). The construct was tested to failure using a Shimadzu ASG 10KN Universal Material Testing Machine (Shimadzu, Tokyo, Japan). Load and mode of construct failure were recorded for 37 individual constructs. There was no significant difference in the load at failure between the 7 mm screw (192 N; range 151–232) and 8 mm screw (181 N; range 150–212) (p>0.05). There was a significant difference between the 7 mm screw and the 9 mm screw (109 N; range 67–151) (p=0.006) and between the 8 mm screw and the 9 mm screw (p=0.015). When using a 9 mm screw, 100% of the constructs failed by cut out of the graft at the tunnel opening. The 7 mm constructs failed by slippage of the tendon from the bone tunnel in 83% of cases, with only 17% failing by cut out at the tunnel opening. The 8 mm constructs demonstrated a mixture of failure modes, with slippage occurring in 58% of cases, cut out in 38% and failure of the graft substance in one case (4%). In this model, screw diameters equal to or 1 mm less than the tunnel/tendon diameter provides better fixation than using a screw 1 mm larger. The mode of failure differs for each of these screws.     

腘绳肌腱与髌腱骨重建ACL不同固定方法的生物力学研究

目的　探讨不同材料与固定方法对髌腱骨 (B PT B)和绳肌腱重建ACL抗拉强度和稳定因素的影响。方法　采用猪膝关节 35个 ,模拟交叉韧带重建 ,实验分为 :骨 髌腱 骨两端界面螺钉固定法 (n=11) ,股骨端单纯肌腱结 (n =13)和肌腱结骨栓 (n =5 )嵌压固定法 ,胫骨端固定采用肌腱编织缝合后骨桥上打结固定法(n=7)、肌腱端编织缝线界面螺钉固定法 (n =6 )和不带缝线肌腱界面螺钉固定法 (n =5 ) ;猪正常膝关节 (n =6 )ACL作为实验对照组。生物力学实验包括最大载荷拔出、抗拉刚度和位移 ,数据进行统计学处理。结果　最大载荷 :绳肌腱结和绳肌腱结骨栓嵌压固定 >B PT B界面螺钉固定 ,前者可以满足正常生理强度需求 ;胫骨固定最大载荷 :绳肌腱编织缝线骨桥打结固定 >肌腱端编织缝合 >无缝线肌腱界面螺钉固定 ;抗拉刚度 :猪正常ACL >B PT B界面螺钉固定 >绳肌腱结和绳肌腱结骨栓固定 ;最大位移 :猪正常ACL 0 1) ,在其他参数上前者优于后者 ,差异均有统计学意义 (P<0 0 5 )。结论　股骨端绳肌腱结和     

A new bicortical tibial fixation technique in anterior cruciate ligament reconstruction with quadruple hamstring graft

We report a prospective series of 101 patients receiving a four-strand semitendinosus-gracilis autograft for anterior cruciate ligament reconstruction using a new bicortical tibial fixation technique with bioabsorbable interference screws. Patients (average age 32 years) were operated on between November 1997 and Mai 1998, and follow-up was at least 12 months postoperatively. The evaluation consisted of history, clinical examination, IKDC score, Cincinnati Knee Score, KT-1000 testing, standardized radiography and magnetic resonance imaging. One hundred patients were available for follow-up. There were two traumatic reruptures 6 and 11 months postoperatively. By IKDC score 87 patients were in groups A and B, 12 in group C, and 2 with a rerupture in group D. Mean Cincinnati Knee Score was 82 (range 46–100), KT-1000 manual maximum at follow-up showed an average difference of 1.7 mm between the sides. Full extension was rapidly achieved in all cases, and flexion averaged 135°. Considering the enlargement caused by the bioabsorbable interference screws, the incidence of tunnel widening was 6.6% on the femoral side and 1.7% on the tibial side. Tunnel widening did not affect the clinical results. Three patients experienced an effusion after more than 6 months postoperatively. There was one infection, which settled without functional impairment after early arthroscopic lavage and intravenous antibiotics. Otherwise no complications occurred. The described technique for anterior cruciate ligament reconstruction combines the advantage of anatomical graft position with sufficient graft fixation. A short intra-articular graft construct with a strong tendon to bone interface was created. Clinically, 87% of patients had a normal or nearly normal IKDC score at follow-up. Magnetic resonance imaging revealed a considerable increase in tunnel area caused by the insertion of the interference screws. On the other hand, the development of a “fibrous interzone” between the graft and the bone tunnel was prevented in most cases. At short-term follow-up the bicortical tibial fixation proved to be efficient even with an aggressive rehabilitation program. Received: 26 November 1999 Accepted: 5 March 2000     

Graft healing in a bone tunnel: bone-attached graft with screw fixation versus bone-free graft with extra-articular suture fixation

The purpose of this study was to clarify differences in tendon graft–to–bone tunnel healing between bone-attached tendon grafts with interference-screw fixation and bone-free tendon grafts with extra-articular suture fixation. In 42 Japanese White rabbits, anterior half replacement of the medial collateral ligament was performed using half of the ipsilateral patellar tendon. At the femoral attachment, the bone-plug-attached graft was fixed with an interference screw (group A). The bone-plug-free graft was fixed by the extra-articular suture fixation technique with sutures tied over a button (group B). Biomechanical and histological evaluations were performed at 2, 4 and 8 weeks postoperatively. In biomechanical evaluation, at 2 or 4 weeks 27 of 28 specimens (96%) were pulled out from the femoral tunnel, while one 4-week specimen and all four 8-week specimens failed at the grafts mid-substance. At 2 weeks, the maximum failure load was 25±10 N and 24±6 N for group A and group B respectively (mean±SD). At 4 weeks, the maximum failure load was 42±17 N and 35±15 N respectively. There were no significant differences in maximum pullout failure load between the groups at 2 or 4 weeks postoperatively. (P=0.887 at 2 weeks and P=0.339 at 4 weeks using ANOVA measurement). Histologically, the bone-attached grafts showed partial bone–to–bone union at the graft–bone tunnel interface at 4 weeks, and complete bony union at 8 weeks. The bone-free grafts exhibited newly formed Sharpey-like collagen fibers at 4 weeks, and strong connection by mature granulation tissue at 8 weeks. Graft–to–bone tunnel healing of bone-attached graft with screw fixation and bone-free graft with extra-articular suture fixation are comparable in terms of biomechanical evaluation during the early postoperative periods.     

Comparison of torsional strengths of bioabsorbable screws for anterior cruciate ligament reconstruction

The goals of this study were to evaluate torsional strength and modes of failure in commercially available bioabsorbable interference screws and to test the effect of screw diameter on torsional strength when screws become jammed during insertion. We tested the Arthrex, BioScrew, Endo-Fix, Phantom, and Sysorb screws, all 20 mm in length. Four major modes of failure were encountered. Analysis of variance revealed that both screw type and diameter had a significant effect on failure torque. The Endo-Fix 7-mm screw had the lowest failure torque (1.07 +/- 0.18 N x m) and the Sysorb 8-mm screw had the highest (5.23 +/- 0.24 N x m). The Sysorb was significantly stronger than all the other screws. The failure torques were within the range that has been reported for manual screw insertion. We concluded that technical factors, which can affect insertion torque, assume particular importance with the use of bioabsorbable interference screws.     

Comparison of the bioabsorbable and metal screw fixation after ACL reconstruction with a hamstring autograft in MRI and clinical outcome: a prospective randomized study

There has never been an MRI study of tunnel widening comparing bioabsorbable to metal screw fixation in autologous hamstring anterior cruciate ligament (ACL) reconstruction. We randomized 62 patients to hamstring ACL reconstruction with either a bioabsorbable (n = 31) or metal screw (n = 31) fixation. The evaluation methods were clinical examination, KT-1000 arthrometric measurement, the International Knee Documentation Committee and Lysholm scores, and MRI. There were no differences between the groups preoperatively. Fifty-five patients (89%) were available at a minimum of 2-year follow-up (range 24–36 months). There was tunnel widening in both groups, but the increase was significantly greater in the AP dimension of the femoral tunnel in the bioabsorbable screw group compared to metal group (P = 0.01). The tibial tunnels showed no intergroup difference. Ninety-four percent of the knees were normal or nearly normal according to the IKDC scores and the average Lysholm score was 91 with no intergroup difference. The follow-up AP tibial tunnel diameter was smaller with normal knee laxity compared to abnormal knee laxity. The graft failure rate in the bioabsorbable screw group was 23% (7/31 patients) and 6% (2/31 patients) in the metal screw group. The use of bioabsorbable screws resulted in more femoral tunnel widening, and more graft failures compared to metal screws. The tunnel widening in the tibia was associated with the knee laxity (P = 0.02).