Fabrication of Polyaniline: Nail/Spindle‐Shaped Morphology

Nail/spindle‐shaped polyaniline is synthesized by chemically oxidizing aniline with ammonium persulfate in a near‐neutral aqueous medium using PVP as the stabilizing agent. The type of dispersing agent, APS content and aniline concentration have obvious impacts on the morphology of the resulting polyaniline. Typically, in the concentration ranges of 1.5–6 × 10^?4 M PVP and 0.02–0.05 M aniline and for molar ratios [APS]:[aniline] of 0.4:1 to 0.8:1, nail/spindle‐shaped polyaniline can be obtained. A possible mechanism is proposed to elucidate the formation process.

     

Microwave‐Assisted Synthesis of Poly(L‐lactic acid) via Direct Melt Polycondensation Using Solid Super‐Acids

A microwave‐assisted method of synthesizing high‐molecular‐weight PLA using SSA as green catalyst was developed. Yellowish PLA with above 2.0 × 10⁴ g · mol^?1 was obtained when the reaction was run at 260 °C within 60 min under microwave irradiation with 0.4 wt.‐% SSA. This method used only 10% of the energy consumption necessary for conventional heating, and the catalyst could be used five times without losing catalytic activity. The improvement in and the decrease in the energy consumption under microwave irradiation suggested that selective heating and hot spots effects played a crucial role. The method was shown to be a time‐saving, green and a promising way to lower the cost and spread the application of PLA.

     

Fluorene‐Based Single‐Chain Copolymers for Color‐Stable White Light‐Emitting Diodes

Fluorene‐based single‐chain copolymers with a white light emitter consisting of a blue and an orange chromophore have been synthesized and their photophysical and electroluminescent properties are investigated. The experimental results suggest that only a relatively small fraction of the orange‐emitting units incorporated into the fluorene is needed to achieve efficient white light emission by controlled incomplete energy transfer. A device from a copolymer with 0.02% DDQ content showed the highest external quantum efficiency of 2.64% with a luminance efficiency of 4.06 cd · A^?1 with CIE coordinates (0.28, 0.24). The EL emissions are extremely stable over a wide range of current densities.

     

Atom Transfer Radical Polymerization and Third‐Order Nonlinear Optical Properties of New Azobenzene‐Containing Side‐Chain Polymers

The atom transfer radical polymerization (ATRP) technique has been successfully applied to synthesize a series of nonlinear optically (NLO) active homopolymers, 4‐(4‐nitrophenyl‐diazenyl) phenyl acrylate ( P ‐ NPAPA ) and 4‐(4‐methoxyphenyl‐diazenyl) phenyl acrylate ( P ‐ MPAPA ), containing azobenzene groups on the side chain. The third‐order NLO properties of the polymer films were measured by the degenerated four‐wave mixing (DFWM) technique. A dependence of the χ⁽³⁾ values and response times of polymers on their number‐average molecular weight and the electronic effect of the substituent (nitro‐ or methoxy‐) on the azobenzene group have been evidenced. The increasing χ⁽³⁾ value of the polymer films at the magnitude of about 10^?10 was displayed with increasing molecular weight and the presence of the push‐pull electronic system contributes much in enhancing the third‐order NLO susceptibility of polymers.

     

Metathetic Selective Degradation of Polyisoprene: Low‐Molecular‐Weight Telechelic Oligomer Obtained from Both Synthetic and Natural Rubber

Summary: Degradation studies of cis‐1,4‐polyisoprene were carried out using first and second generation Grubbs catalysts to achieve end‐functionalized acetoxy oligomers in both an organic solvent and a latex phase at room temperature. Well‐defined acetoxy telechelic polyisoprene structures were obtained in a selective manner with a range of from 10 000 to 30 000, with a polydispersity index of around 2.5.

Structure produced by the metathetic depolymerization of hydroxy telechelic cis‐1,4‐polyisoprene.     

Synthesis of Heterobifunctional Hyperbranched Polyethylenes Tethered with Dual Acryloyl and 2‐Bromoisobutyryl Functionalities via One‐Pot Chain‐Walking Terpolymerization

A one‐step synthesis of heterobifunctional hyperbranched polyethylenes covalently tethered with dual acryloyl and 2‐bromoisobutyryl functionalities at controllable contents is reported. It is achieved in one pot by chain‐walking terpolymerization of ethylene with two functional acrylate comonomers, 1,6‐hexanediol diacrylate and 2‐(2‐bromoisobutyryloxy) ethyl acrylate. The unique chain‐walking mechanism renders the hyperbranched polymer chain topology and its remarkable capability in incorporating acrylate comonomers enables the incorporation of both comonomers to give two valuable functionalities. The two comonomers exhibit nearly equal vinyl reactivity and are incorporated independently in the terpolymerization with their molar contents controlled by adjusting the comonomer feed concentrations.

     

Photodeformable Polymers: A New Kind of Promising Smart Material for Micro‐ and Nano‐Applications

Summary: Starting in the 1960s, several kinds of photodeformable polymers have been developed, such as monolayers, polymer gels, solid films and liquid‐crystalline elastomers with different photodeformation mechanisms. This field evolved slowly until recently when significant achievements have been made. Most recently, Lendlein and co‐workers have put forward another new concept – using photo‐crosslinking to prepare deformable polymers with various pre‐determined shapes (Nature 2005 , 434, 879). This highlight gives a general introduction into photodeformable polymers and brings forth future challenges.

A polymer film doped with SCAA molecules where (a) is the permanent shape, (b) is the temporary shape and (c) is the recovered shape.     

Cylindrical Polypeptide Brushes

Summary: Cylindrical brushes with poly(L ‐lysine) and poly(L ‐glutamate) side chains were prepared by “grafting through” and “grafting from” techniques. Grafting from is shown to be more successful for the synthesis of cylindrical brushes with high molar mass main and side chains.

AFM height image of polypeptide brushes with protected polylysine side chains spin‐cast from HFIP solution.     

Kinetic and Mechanistic Studies of Carboxylic Acid–Bisoxazoline Chain‐Coupling Reactions

Kinetic studies of the reactions between a model carboxylic acid and bisoxazoline coupling agents, namely 2,2′‐(1,3‐phenylene)bis(2‐oxazoline) ( mbox ), 2,2′‐(1,4‐phenylene)bis(2‐oxazoline) ( pbox ), and 2,2′‐(2,6‐pyridylene)bis(2‐oxazoline) ( pybox ), were carried out in bulk at 140–220 °C. A second‐order two‐step reaction mechanism was proposed and was verified by the experimental results. The results also indicate that the reactivity of the oxazoline groups is unchanged after the reaction of the other oxazoline group of the same coupling agent moiety, that is, oxazoline groups are equireactive. Rate constants and activation enthalpies and entropies were determined, allowing the comparison of bisoxazoline reactivity. The following reactivity order was found: pybox > mbox > pbox . The formation of a stabilized protonated complex is postulated to explain the much higher reaction rate observed with the new coupling agent pybox .

Variation of the experimental concentrations of reactants and reaction products versus time.     

Poly(4‐hexyl‐1,2,4‐triazole‐4H): An Electron Semiconducting Analogue to Regioregular Poly(hexylthiophene)

Summary: For the development of n‐channel field‐effect transistors it is indispensable to look for semiconducting polymers with electrons as majority charge carriers (n‐type). In addition high electron mobility values are of significant advantage in these compounds. Polymers with electron transporting properties have been rarely investigated. Main chain polymers with strong acceptor units like 1,2,4‐triazoles‐4H are potential candidates for electron transporting materials in electronic devices. Therefore, a synthetic pathway leading to an organo‐soluble polymer consisting only of 4‐hexyl‐1,2,4‐triazole‐4H units in the main chain is presented in this work. We will report the synthesis using modified classical polycondensation. The chemical and electronic properties of the polytriazole have been investigated in detail. The material has been used to prepare “electron‐only” devices for the calculation of the electron mobility.

The suggested chemical structure of poly(4‐hexyl‐1,2,4‐triazole‐4H) (PHTA).     

Well‐Defined Miktocycle Eight‐Shaped Copolymers Composed of Polystyrene and Poly(ε‐caprolactone): Synthesis and Characterization

A series of well‐defined miktocycle number‐eight‐shaped copolymers composed of cyclic polystyrene (PS) and cyclic poly(ε‐caprolactone) (PCL) have been successfully synthesized by a combination of atom transfer radical polymerization (ATRP), ring‐opening polymerization (ROP), and “click” reaction. The synthesis involves three steps: 1) preparation of tetrafunctional initiator with two acetylene groups, one hydroxyl group and a bromo group; 2) preparation of two azide‐terminated block copolymers, N₃‐PCL‐(CH?C)₂‐PS‐N₃, with two acetylene groups anchored at the junction; and 3) intramolecular cyclization of the block copolymer through “click” reaction under high dilution. The ¹H NMR, FT‐IR, and gel permeation chromatography (GPC) techniques are applied to characterize the chemical structures of the resulting intermediates and the target polymers. Their thermal behavior is investigated by differential scanning calorimeter (DSC). The decrease in chain mobility of eight‐shaped copolymers restricts the crystallization of PCL.

     

Chain‐Length‐Dependent Termination in Radical Polymerization of Acrylates

The technique of SPPLP EPR, which is single‐pulse pulsed‐laser polymerization (SPPLP) in conjunction with electron paramagnetic resonance (EPR) spectroscopy, is used to carry out a detailed investigation of secondary (chain‐end) radical termination of acrylates. Measurements are performed on methyl acrylate, n‐butyl acrylate, and dodecyl acrylate in bulk and in toluene solution at ?40 °C. The reason for the low temperature is to avoid formation of mid‐chain radicals (MCRs), a complicating factor that has imparted ambiguity to the results of previous studies of this nature. Consistent with these previous studies, composite‐model behavior for chain‐length‐dependent termination (CLDT) rate coefficients, , is found in this work. However, lower and more reasonable values of α_s, the exponent for variation of at short chain lengths, are found in the present study. Most likely this is because of the absence of MCRs, thereby validating the methodology of this work. Family‐type termination behavior is observed, with the following average parameter values adequately describing all results, regardless of acrylate or the presence of toluene: α_s = 0.79, α_l = 0.21 (long chains) and i_c ≈ 30 (crossover chain length). All indications are that these values carry over to termination of acrylate chain‐end radicals at higher, more practical temperatures. Further, these values largely make sense in terms of what is understood about the physical meaning of the parameters. Variation of the rate coefficient for termination between monomeric radicals, , is found to be well described by the simple Smoluchowski and Stokes–Einstein equations. This allows easy prediction of for different alkyl acrylates, solvent, and temperature. Through all this the unrivalled power of SPPLP EPR for measuring and understanding (chain‐length‐dependent) termination rate coefficients shines through.

     

gem‐Dimethyl Effects in the Thermal Behavior of Polyethylene

Summary: Polyethylene can be rendered completely amorphous via the insertion of regularly spaced gem‐dimethyl defects along its backbone, where frequency of insertion is the deciding factor in achieving the totally amorphous state. Accurate placement of defects along polyethylene's backbone is achieved with step polymerization metathesis chemistry (the ADMET reaction) rather than using chain polymerization techniques. These gem‐dimethyl polyethylene macromolecules, when compared with other ADMET ethylene‐based model materials, demonstrate that steric bulk, frequency, and distribution of the defect along the polymer backbone are more important than stereoregularity (tacticity) when the defects are spaced nine carbon atoms or more apart. Comparisons are made between gem‐dimethyl “defects” and methyl “defects” in a polyethylene backbone.

Synthetic scheme for the ADMET‐made gem‐dimethyl model polyethylenes ( 14a–c ).     

Nanoscale Analysis of Polymer Interfaces by Energy‐Filtering Transmission Electron Microscopy

Summary: Energy‐filtering transmission electron microscopy (EFTEM) was employed for the analysis of polymer‐polymer interfaces. To attain imaging and spectral analyses with a spatial resolution of 10 nm, problems arising in the EFTEM analysis for polymer specimens were investigated. Interfaces in poly(methyl methacrylate)/polystyrene‐co‐polyacrylonitrile random copolymer (PMMA/SAN) bilayer films annealed at different temperatures were analyzed by means of elemental mapping and Image‐EELS on EFTEM and the effect of the annealing temperature on the interfacial structures was also investigated.

     

Nitroxide‐Mediated Radical Polymerization of N‐tert‐Butylacrylamide

The nitroxide‐mediated polymerization of N‐tert‐butylacrylamide (TBAM) in DMF at 120 °C using SG1/DEPN and AIBN has been investigated. Linear growth in number‐average molecular weight ( ) versus conversion and narrow molecular weight distributions (MWDs) with high livingness were obtained up to ≈8 000 g · mol^?1. For higher molecular weights, the MWDs gradually became broader with low molecular weight tailing, and deviated downwards from theoretical values. Quantitative analyses of MWDs, along with specifically designed conventional radical polymerizations at 120 °C, were consistent with chain transfer to monomer limiting the attainable . This finding can be equally applied to existing literature polymerizations of TBAM.

     

“Click” Synthesis of a Bipolar Dendrimer as a Host Material for Electrophosphorescent Devices

A new solution‐processable bipolar dendrimer with carbazole units as hole‐transporting units and oxadiazole units as electron‐transporting units was efficiently synthesized based on a convergent approach by alternation of a Cu‐catalyzed azide/alkyne cycloaddition reaction and Williamson ether synthesis. The orthogonal chemistry completely avoided protection and activation of the focal points in the process of dendrimer synthesis. The dendrimer showed a wide bandgap and good thermal stability. Electrophosphorescent devices with the configuration ITO/PEDOT:PSS/bipolar dendrimer:Ir(ppy)₃/TPBI/LiF/Al were fabricated. The devices showed a maximum current efficiency of 16.8 cd · A^?1, a maximum power efficiency of 4.22 lm · W^?1 and an external quantum efficiency of 5.7%.

     

Polystyrene with Improved Chain‐End Functionality and Higher Molecular Weight by ARGET ATRP

The bromine chain‐end functionality of polystyrene (PSt) prepared by activators regenerated by electron transfer for atom transfer radical polymerization (ARGET ATRP) was analyzed using 500 MHz ¹H nuclear magnetic resonance (NMR). Bulk polymerization of styrene (St) was carried out with 50 ppm of copper in the presence of tris[2‐(dimethylamino)ethyl]amine (Me₆TREN) ligand and tin(II) 2‐ethylhexanoate [Sn(EH)₂] reducing agent at 90 °C. Due to the use of a low concentration of an active Cu/ligand catalyst complex, it was possible to significantly decrease the occurrence of catalyst‐based side reactions (β‐H elimination). As a result, compared to PSt prepared via normal ATRP, PSt with improved chain‐end functionality was obtained. For example, at 92% monomer conversion in normal ATRP only 48% of chains retained chain‐end functionality, whereas 87% of the chains in an ARGET ATRP still contained halogen functionality. PSt with controlled molecular weight ( = 11 600 g · mol^?1, = 9 600 g · mol^?1) and narrow molecular weight distribution ( = 1.14) was prepared under these conditions. In addition, as a result of decreased frequency of side reactions in ARGET ATRP, PSt with relatively high molecular weight was successfully prepared ( = 185 000 g · mol^?1, = 1.35).

     

Aromatic Polyethers with a 4‐Chloro‐3‐trifluoromethylphenyl Group

Summary: A novel bisphenol, (4‐chloro‐3‐trifluoromethyl)phenylhydroquinone (3FC‐PH), was synthesized via a three‐step synthetic procedure. Four aromatic polyethers based on 3FC‐PH were prepared via a nucleophilic aromatic substitution polycondensation. These polymers had a high thermal stability, and the temperatures at a 5% weight loss were above 516 °C in air. The solubility of the polyethers was improved by the introduction of bulky pendant groups. The average refractive indices of the polymer films at 1 320 nm were in the range 1.5381–1.6145. The dielectric constants of the polyether films estimated from the refractive indices were 2.69–2.98. Highly fluorinated 3FC‐PAE exhibited lower light absorption in the near‐IR region.

Part of the ¹H NMR spectra of 3FC‐PAE.     

“One‐Pot” In Situ Formation of Gold Nanoparticles within Poly(acrylamide) Hydrogels

This paper focuses on two different strategies to incorporate gold nanoparticles (AuNPs) into the matrix of polyacrylamide (PAAm) hydrogels. Poly(ethyleneimine) (PEI) is used as both reducing and stabilizing agent for the formation of AuNPs. In addition, the influence of an ionic liquid (IL) (i.e., 1‐ethyl‐3‐methylimidazolium ethylsulfate) on the stability of the nanoparticles and their immobilization in the hydrogel is investigated The results show that AuNPs surrounded by a shell containing PEI and IL, synthesized according to the “one‐pot” approach, are much better immobilized within the PAAm hydrogel. Hereby, the IL is responsible for structural changes in the hydrogel as well as the improved stabilization and embedding of the AuNPs into the polymer gel matrix.

     

Characterization of Carbon Monoxide Centered Triads in Poly[ethylene‐co‐(butyl acrylate)‐co‐(13C‐carbon monoxide)] by Isotopic Labeling and Two‐Dimensional NMR

Summary: Poly[ethylene‐co‐(butyl acrylate)‐co‐(carbon monoxide)] (polyEBC) samples, prepared from ¹³C‐labeled carbon monoxide, were characterized using two dimensional (2D) pulsed field gradient (PFG) 750 MHz NMR spectroscopy. To elucidate the complex mixture of structures present in this terpolymer, 2D ¹H/¹³C‐heteronuclear multiple bond correlation (HMBC) experiments were conducted by selectively exciting the enhanced peaks resulting from ¹³C‐labeling. High resolution 2D NMR combined with ¹³C‐labeling of the polymer greatly simplifies the 2D NMR spectra, selectively enhances the weak peaks from low occurrence C‐centered triad structures and aids in their resonance assignments.