Kinematic comparison between mobile-bearing and fixed-bearing inserts in NexGen legacy posterior stabilized flex total knee arthroplasty

Femoral component rollback and tibial rotation were evaluated using lateral radiographs taken during passive knee flexion under fluoroscopy in NexGen Legacy Posterior Stabilized Flex (Zimmer, Warsaw, Ind) total knee arthroplasties (TKAs; 30 with mobile insert and 26 with fixed insert). Measured maximal flexion angle demonstrated no significant differences. Femoral component rollback was observed predominantly in TKAs with fixed insert in more than 45 degrees flexion and correlated with maximal flexion angle in each group. Tibial internal rotation was more significant in TKAs with mobile insert in maximal flexion. However, tibial internal rotation from 90 degrees to maximal flexion, which demonstrated correlation with maximal flexion angle in each group, did not show significant difference. The kinematic differences between 2 inserts seemed to have little relevance to the maximal flexion angle.     

Anatomic vs Dome Patella: Is There a Difference Between Fixed- vs Mobile-Bearing Posterior-Stabilized Total Knee Arthroplasties?

BackgroundIt has been hypothesized that the patella, working in conjunction with both medial and lateral femoral condyles, can influence kinematic parameters such as posterior femoral rollback and axial rotation. The objective of this study is to determine the in vivo kinematics of subjects implanted with a fixed-bearing (FB) or mobile-bearing (MB) posterior-stabilized (PS) total knee arthroplasty (TKA), with a specific focus on evaluating the impact that Anatomic and Medialized Dome patellar components have on tibiofemoral kinematic patterns.MethodsTibiofemoral kinematics were assessed for 40 subjects; 20 with an anatomic patella and 20 with a dome patella. Within these groups, 10 subjects received an FB PS TKA and 10 subjects received an MB PS TKA. All subjects were analyzed using fluoroscopy while performing a deep knee bend activity. Kinematics were collected during specific intervals to determine similarities and differences in regard to patella and bearing type.ResultsThe greatest variation in kinematics was detected between the 2 Anatomic patellar groups. Specifically, the MB-Anatomic subjects experienced greater translation of the lateral condyle, the highest magnitude of axial rotation, and the highest range of motion compared to the FB-Anatomic subjects. Subjects with a Dome Patella displayed much variability among the average kinematics, with all parameters between FB and MB cohorts being similar.ConclusionThe findings in this study suggest that subjects with an Anatomic patellar component could have more normal kinematic patterns with an MB PS TKA as opposed to an FB PS TKA, while subjects with a Dome patella could achieve similar kinematics regardless of TKA type.     

In vivo kinematics of mobile-bearing knee arthroplasty in deep knee bending motion.

The current study aimed to analyze kinematics during deep knee bending motion by subjects with fully congruent mobile-bearing total knee arthroplasties allowing axial rotation and anteroposterior (AP) gliding. Twelve subjects were implanted with Dual Bearing Knee prostheses (DBK, slot type: Finsbury Orthopaedics, Surrey, UK). These implants include a mobile-bearing insert that is fully congruent with the femoral component throughout flexion and allows axial rotation and limited AP translation. Sequential fluoroscopic images were taken in the sagittal plane during loaded knee bending motion. In vivo kinematics were analyzed using a two- to three-dimensional registration technique, which uses computer-assisted design models to reproduce the spatial position of femoral and tibial components from single-view fluoroscopic images. The average femoral component demonstrated 13.4 degrees external axial rotation for 0-120 degrees flexion. On average, the medial condyle moved anteriorly 6.2 mm for 0-100 degrees flexion, then posteriorly 4.0 mm for 100-120 degrees flexion. On average, the lateral condyle moved anteriorly 1.0 mm for 0-40 degrees flexion, then posteriorly 8.7 mm for 40-120 degrees flexion. The typical subject exhibited a lateral pivot pattern from extension to 60 degrees flexion and a central pivot pattern from 60 degrees to 100 degrees flexion, patterns that are not usually observed in normal knees. Subsequently from 100 degrees to 120 degrees flexion, a rollback pattern was reproduced in which bilateral condyles moved backward.     

In Vivo Knee Kinematics for a Cruciate Sacrificing Total Knee Arthroplasty Having Both a Symmetrical Femoral and Tibial Component

BackgroundEarly total knee arthroplasty (TKA) designs were symmetrical, but lead to complications due to over-constraint leading to loosening and poor flexion. Next-generation TKAs have been designed to include asymmetry, pertaining to the trochlear groove, femoral condylar shapes, and/or the tibial component. More recently, an advanced posterior cruciate sacrificing (PCS) TKA was designed to include both a symmetrical femoral component with a patented V-shaped trochlear groove and a symmetrical tibial component with an ultracongruent insert, in an attempt to reduce inventory costs. Because previous PCS TKA designs produced variable results, the objective of this study is to determine and evaluate the in vivo kinematics for subjects implanted with this symmetrical TKA.MethodsTwenty-one subjects, implanted with symmetrical PCS fixed-bearing TKA, were asked to perform a weight-bearing deep knee bend (DKB) while under fluoroscopic surveillance. A 3-dimensional to 2-dimensional registration technique was used to determine each subject’s anteroposterior translation of lateral and medial femoral condyles as well as tibiofemoral axial rotation and their weight-bearing knee flexion.ResultsDuring the DKB, the average active maximum weight-bearing flexion was 111.7° ± 13.3°. On average, from full extension to maximum knee flexion, subjects experienced −2.5 ± 2.0 mm of posterior femoral rollback of the lateral condyle and 2.5 ± 2.2 mm of medial condyle motion in the anterior direction. This medial condyle motion was consistent for the majority of the subjects, with the lateral condyle exhibiting rollback from 0° to 60° of flexion and then experienced an average anterior motion of 0.3 mm from 60° to 90° of knee flexion. On average, the subjects in this study experienced 6.6°± 3.3° of axial rotation, with most of the rotation occurring in early flexion, averaging 4.9°.ConclusionAlthough subjects in this study were implanted with a symmetrical PCS TKA, they did experience femoral rollback of the lateral condyle and a normal-like pattern of axial rotation, although less in magnitude than the normal knee. The normal axial rotation pattern occurred because the lateral condyle rolled in the posterior direction, while the medial condyle moved in the anterior direction. Interestingly, the magnitude of posterior femoral rollback and axial rotation for subjects in this study was similar in magnitude reported in previous studies pertaining to asymmetrical TKA designs. It is proposed that more patients be analyzed having this TKA implanted by other surgeons.     

In vivo comparison of knee kinematics for subjects having either a posterior stabilized or cruciate retaining high-flexion total knee arthroplasty

The objective of this study was to determine the in vivo kinematics for subjects having either a fixed posterior stabilized (PS) or cruciate retaining (CR) high-flexion total knee arthroplasty (TKA). Three-dimensional kinematics from full extension to maximum flexion were determined for 30 subjects (15 PS, 15 CR) using fluoroscopy. On average, the PS subjects demonstrated 112 degrees of weight-bearing (WB) flexion, -6.4 mm of posterior femoral rollback, and 2.9 degrees of axial rotation. The CR subjects averaged 117 degrees of WB flexion, -4.9 mm of posterior femoral rollback, and 4.8 degrees of axial rotation. Posterior femoral rollback of the lateral condyle occurred for all PS TKAs and in 93% of the CR TKAs. Only 2 subjects in each group experienced greater than 1.0 mm of condylar lift-off. Subjects in both TKA groups demonstrated excellent WB ranges of motion and kinematic patterns similar to the normal knee, but less in magnitude.     

In Vivo Kinematic Comparison Between Mobile-Bearing and Fixed-Bearing Total Knee Arthroplasty During Step-Up Activity

Mobile-bearing total knee arthroplasty (TKA) expects high conformity and low contact stress. It is designed to correct the rotational mismatch between femoral and tibial components. We examined the difference in weight-bearing knee kinematics in patients with mobile-bearing and fixed-bearing TKA performing step-up activities. We randomly assigned 40 knees (37 patients) to mobile-bearing TKA (n = 20) or fixed-bearing TKA (n = 20). Using fluoroscopic imaging we evaluated knee kinematics during step-up activity one year after surgery. The total extent of rotation was not different for the two TKAs. Due to the axial rotation of the polyethylene insert, patients with mobile-bearing TKA had a wider range of absolute axial rotation. The position of the medial and the lateral condyles was significantly more posterior in the fixed-bearing TKA. There were only minor kinematic differences between the two TKAs. The polyethylene insert in the mobile-bearing TKA moved as designed especially with respect to the self-alignment feature.     

In vivo kinematic analysis of a high-flexion posterior stabilized fixed-bearing knee prosthesis in deep knee-bending motion

The objective of this study was to evaluate in vivo kinematics of a high-flexion, posterior-stabilized fixed-bearing, total knee arthroplasty in weight-bearing deep knee-bending motion. A total of 20 knees implanted with the Scorpio Non-Restrictive Geometry knee system in 17 patients were assessed in this study. The Scorpio Non-Restrictive Geometry is a recent implant design with modifications made to accommodate a higher flexion range of motion and greater axial rotation, particularly during more functionally demanding activities. Patients were examined during a deep knee-bending motion using fluoroscopy, and femorotibial motion was determined using a 2-dimensional to 3-dimensional registration technique. The average flexion angle was 126.5° (110°-149°). The femoral component demonstrated a mean of 13.5° (5.2°-21°) external rotation. The external rotation increased up to maximum flexion. The pivot pattern was a medial pivot pattern similar to that reported in normal knee kinematics.     

In Vivo Knee Kinematics: How Important Are the Roles of Femoral Geometry and the Cruciate Ligaments?

BackgroundWhile posterior cruciate-retaining (PCR) implants are a more common total knee arthroplasty (TKA) design, newer bicruciate-retaining (BCR) TKAs are now being considered as an option for many patients, especially those that are younger. While PCR TKAs remove the ACL, the BCR TKA designs keep both cruciate ligaments intact, as it is believed that the resection of the ACL greatly affects the overall kinematic patterns of TKA designs. The objectives of this study are to assess the in vivo kinematics for subjects implanted with either a PCR or BCR TKA and to compare the in vivo kinematic patterns to the normal knee during flexion. These objectives were achieved with an emphasis on understanding the roles of the cruciate ligaments, as well as the role of changes in femoral geometry of nonimplanted anatomical femurs vs implanted subjects having a metal femoral component.MethodsTibiofemoral kinematics of 50 subjects having a PCR (40 subjects) or BCR (10 subjects) TKA were analyzed using fluoroscopy while performing a deep knee bend activity. The kinematics were compared to previously published normal knee data (10 subjects). Kinematics were determined during specific intervals of flexion where the ACL or PCL was most dominant.ResultsIn early flexion, subjects having a BCR TKA experienced more normal-like kinematic patterns, possibly attributed to the ACL. In mid-flexion, both TKA groups exhibited variable kinematic patterns, which could be due to the transitional cruciate ligament function period. In deeper flexion, both TKA functioned more similar to the normal knee, leading to the assumption that the PCL was properly balanced and functioning in the TKA groups. Interestingly, during late flexion (after 90°), the kinematic patterns for all three groups appeared to be statistically similar.ConclusionSubjects having a PCR TKA experienced greater weight-bearing flexion than the BCR TKA group. Subjects having a BCR TKA exhibited a more normal-like kinematic pattern in early and late flexion. The normal knee subjects achieved greater lateral condyle rollback and axial rotation compared to the TKA groups.     

In vivo determination of kinematics for subjects having a Zimmer Unicompartmental High Flex Knee System

The objective of this study was to determine the in vivo kinematics during weight-bearing and non–weight-bearing activities for subjects with a unicompartmental knee arthroplasty (UKA) designed for high flexion and implanted with minimally invasive techniques. A total of 30 UKAs implanted in 18 patients were analyzed. All patients were implanted with a medial Zimmer Unicompartmental High Flex Knee System (Zimmer Inc, Warsaw, Ind). Under fluoroscopic surveillance, each patient performed weight-bearing deep knee bend, normal gait, and passive flexion. The kinematics of the medial UKA was determined using a 3-dimensional model registration technique. On average, the implant experienced posterior femoral rollback and normal axial rotation during flexion. However, the kinematic patterns for each patient were not consistent, and the variability was high during flexion and stance phase of gait.     

In vivo kinematics of a low contact stress rotating platform total knee arthroplasty system under weight bearing and non-weight bearing condition

Background

The patterns and magnitudes of axial femorotibial rotation are variable due to the prosthesis design, ligamentous balancing, and surgical procedures. We aimed to investigate the effects of the weight bearing (WB) condition on the kinematics of mobile-bearing total knee arthroplasty (TKA).

Methods

We examined 12 patients (19 knees) implanted with a low contact stress (LCS) mobile-bearing TKA system using a two-dimensional to three-dimensional registration technique. The in vivo kinematics of dynamic deep knee flexion under WB and non-WB (NWB) conditions were compared. We evaluated the knee range of motion, femoral axial rotation relative to the tibial component, anteroposterior translation, and kinematic pathway of the femorotibial contact point for both the medial and lateral sides.

Results

Under the WB condition, the mean range of motion was 117.8° ± 16.7°. Under the NWB condition, the mean range of motion was 111.0° ± 4.4°. The mean range of axial rotation from full extension to maximum flexion was 3.0° ± 1.5° under the WB condition and 2.2° ± 1.0° under the NWB condition. With regard to the anteroposterior translation, the LCS mobile-bearing TKA system showed the same kinematic patterns under both conditions, except for axial rotation at 0°, 10°, and 110°. From hyperextension to maximum flexion, the kinematic pattern reflected a central pivot under both conditions.

Conclusions

In conclusion, this study demonstrated that, in an LCS mobile-bearing TKA system, knee kinematics showed the same patterns under NWB and WB conditions, except for axial rotation at the early phase. Further understanding of knee kinematics could provide us with useful information for future design concepts of TKA implants.     

Bi‐Cruciate Retaining Total Knee Arthroplasty Does Not Restore Native Tibiofemoral Articular Contact Kinematics During Gait

Bi‐cruciate retaining (BCR) total knee arthroplasty (TKA) design preserves both anterior and posterior cruciate ligaments with the potential to restore normal posterior femoral rollback and joint kinematics. Abnormal knee kinematics and “paradoxical” anterior femoral translation in conventional TKA designs have been suggested as potential causes of patient dissatisfaction. However, there is a paucity of data on the in vivo kinematics and articular contact behavior of BCR‐TKA. This study aimed to investigate in vivo kinematics, articular contact position, and pivot point location of the BCR‐TKA during gait. In vivo kinematics of 30 patients with unilateral BCR‐TKA during treadmill walking was determined using validated dual fluoroscopic imaging tracking technique. The BCR‐TKA exhibited less extension than the normal healthy knee between heel strike and 48% of gait cycle. Although the average external rotation trend observed for BCR TKA was similar to the normal healthy knee, the range of motion was not fully comparable. The lowest point of the medial condyle showed longer anteroposterior translation excursion than the lateral condyle, leading to a lateral‐pivoting pattern in 60% of BCR TKA patients during stance phase. BCR‐TKA demonstrated no statistical significant differences in anterior–posterior translation as well as varus rotation, when compared to normal healthy knees during the stance phase. However, sagittal plane motion and tibiofemoral articular contact characteristics including pivoting patterns were not fully restored in BCR TKA patients during gait, suggesting that BCR TKA does not restore native tibiofemoral articular contact kinematics. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:1929–1937, 2019     

Kinematic Performance of Gradually Variable Radius Posterior-Stabilized Primary TKA During Various Activities: An In Vivo Study Using Fluoroscopy

BackgroundPosterior-stabilized total knee arthroplasty (TKA) with gradually variable radii (G-curve) femoral condylar geometry is now available. It is believed that a G-curve design would lead to more mid-flexion stability leading to reduced incidence of paradoxical anterior slide. The objective of this study was to assess the in vivo kinematics for subjects implanted with this type of TKA under various conditions of daily living.MethodsTibiofemoral kinematics of 35 patients having posterior-stabilized TKA with G-curve design were analyzed using fluoroscopy while performing three activities: weight-bearing deep knee bend, gait, and walking down a ramp. The subjects were assessed for range of motion, condylar translation, axial rotation, cam-spine engagement, and condylar lift-off.ResultsThe average weight-bearing flexion during deep knee bend was 111.4°. On average, the subjects exhibited 5.4 mm of posterior rollback of the lateral condyle and 2.0 mm of the medial condyle from full extension to maximum knee flexion. The femur consistently rotated externally with flexion, and the average axial rotation was 5.2°. Overall movement of the condyles during gait and ramp-down activity was small. No incidence of condylar lift-off was observed.ConclusionSubjects in this study experienced consistent magnitudes of posterior femoral rollback and external rotation of the femur with weight-bearing flexion. The variation is similar to that previously reported for normal knee where the lateral condyle moves consistently posterior compared to the medial condyle. Subjects experienced low overall mid-flexion paradoxical anterior sliding and no incidence of condylar lift-off leading to mid-flexion stability.     

Restoration of the joint line in total knee arthroplasty

The purpose of the study was to assess the effect of the joint line position in a posterior cruciate ligament–retaining, mobile-bearing total knee arthroplasty (TKA). Seventy-six consecutive TKAs performed by 1 surgeon were prospectively assessed for a minimum of 2.5 years. Posterior cruciate ligament–retaining, mobile-bearing TKA was performed in all cases. The joint line was elevated 1 mm on average (range, −11 to +10). There was no correlation between joint line position and range of motion, knee function scores, knee pain scores, or patellar height. The joint line position in a posterior cruciate–retaining, mobile-bearing (LCS AP Glide; DePuy, Leeds, United Kingdom) TKA did not affect the early clinical results.     

Changes in the Functional Flexion Axis of the Knee Before and After Total Knee Arthroplasty Using a Navigation System

Long term satisfaction of patients with total knee arthroplasty (TKA) has lagged behind that of total hip arthroplasty. One possible reason is the failure of the artificial joint to recreate natural kinematics of the knee. This study evaluated the pre and post implant functional flexion axis in the knees of 285 total knee arthroplasty patients using a surgical navigation system. Results showed that post-implant there was less femoral rollback early in flexion on the lateral side of the joint than pre-implant. Designing future generations of knee implants to allow for this motion may give patients a more ‘natural’ feeling knee and may benefit outcomes.     

Preclinical Evaluation Method for Total Knees Designed to Restore Normal Knee Mechanics

The objective was to develop a simple, rapid, and low-cost method for evaluating proposed new total knee arthroplasty (TKA) models and then to evaluate 3 different TKA models with different kinematic characteristics. A “desktop” knee testing rig was used to apply forces and moments over a full flexion range, representing a spectrum of positions and activities; and the positions of the femur on the tibia were measured. The average neutral path of motion (for compressive force only) and the laxities about the neutral path (for superimposed shear and torque) were determined from 8 knee specimens to be used as a benchmark for the TKA evaluations. A typical posterior-stabilized TKA did not display the normal external femoral rotation with flexion and also showed abnormal anterior sliding on the medial side. A medial-pivot type of guided-motion design showed medial stability comparable to anatomical but still did not produce external femoral rotation and posterior lateral displacement with flexion. The addition of a central cam-post produced the rotation and displacement but only after 75° of flexion. It was concluded that the test method satisfied the objective and could be used as a design tool for evaluating new and existing designs, as well as for formulating a TKA with anatomical characteristics.     

Knee kinematics of high-flexion activities of daily living performed by male Muslims in the Middle East

Full flexion is critical for total knee arthroplasty (TKA) patients in the Middle East, where daily activities require a high range of motion in the lower limb. This study aimed to increase understanding of the knee kinematics of normal Muslim subjects during high-flexion activities of daily living, such as kneeling, Muslim prayer, sitting cross-legged, and squatting. The early postoperative kinematics for a select group of Muslim, high-flexion TKA patients are also reported. Mean curves were compared between the normal group and the TKA group. During kneeling, the average maximum flexion was 141.6° for the normal group and 140.2° for the TKA group. The normal group's maximum and minimum knee angles (flexion, abduction, external rotation) were reported and, with the exception of maximum extension, were not significantly different from the TKA group, despite short postoperative times.     

Computational analysis of customized cruciate retaining total knee arthroplasty restoration of native knee joint biomechanics

The purpose of this study was to verify if customized prosthesis better preserves the native knee joint kinematics and provides lower contact stress on the polyethylene (PE) insert owing to the wider bone preservation than that of standard off‐the‐shelf prosthesis in posterior cruciate‐retaining type total knee arthroplasty (TKA). Validated finite element (FE) models for were developed to evaluate the knee joint kinematics and contact stress on the PE insert after TKA with customized and standard off‐the‐shelf (OTS) prostheses as well as in normal healthy knee through FE analysis under dynamic loading conditions. The contact stresses on the customized prosthesis decreased by 18% and 8% under gait cycle loading conditions, and 24% and 9% under deep‐knee‐bend loading conditions, in the medial and lateral sides of the PE insert, respectively, compared with the standard OTS prosthesis. The anterior‐posterior translation and internal‐external (IE) rotation in customized TKA were more similar to native knee joint behaviors compared with standard OTS TKA under gait loading conditions. The difference from normal knee kinematics was lower for femoral rollback and IE rotation in customized TKA than in standard OTS TKA in the deep‐knee‐bend condition. In general, customized prostheses achieve kinematics that are close to those of the native healthy knee joint and have better contact stresses than standard OTS prostheses in gait and deep‐knee‐bend loading conditions.     

In Vivo Movement of Femoral Flexion Axis of a Single-Radius Total Knee Arthroplasty

The objective of this study was to investigate in vivo femoro-tibial motion using the movement of femoral flexion axis of a single-radius TKA. We examined 20 clinically successful knees with a single-radius posterior stabilized TKA to evaluate the kinematics of deep knee flexion using 2–3-dimensional registration techniques. The mean knee flexion range of motion was 117.8°. The mean rotation of the femoral component was 7.6° external rotation. The mean knee flexion angle at initial post-cam engagement was 55.2°. No paradoxical movement of femoral component was shown until 70° flexion, afterward the femoral component rolled back with flexion. The data showed that the design of this prosthesis might contribute to reduce the paradoxical anterior femoral movement and provide stability in mid-flexion ranges.     

The Effect of Total Knee Arthroplasty on Knee Joint Kinematics and Kinetics During Gait

This study determined how total knee arthroplasty (TKA) altered knee motion and loading during gait. Three-dimensional kinematic and kinetic gait patterns of 42 patients with severe knee osteoarthritis were collected 1 week prior and 1-year post-TKA. Principal component analysis extracted major patterns of variability in the gait waveforms. Overall and midstance knee adduction moment magnitude decreased. Overall knee flexion angle magnitude increased due to an increase during swing. Increases in the early stance knee flexion moment and late stance knee extension moment were found, indicating improved impact attenuation and function. A decrease in the early stance knee external rotation moment indicated alteration in the typical rotation mechanism. Most changes moved toward an asymptomatic pattern and would be considered improvements in motion, function, and loading.     

In Vivo Kinematic Comparison of a Bicruciate Stabilized Total Knee Arthroplasty and the Normal Knee Using Fluoroscopy

Background

The bicruciate stabilized (BCS) total knee arthroplasty (TKA) features asymmetrical bearing geometry and dual substitution for the anterior cruciate ligament and posterior cruciate ligament (PCL). Previous TKA designs have not fully replicated normal knee motion, and they are characterized by lower magnitudes of overall rollback and axial rotation than the normal knee.