Effect of Er on Microstructure and Corrosion Behavior of Al–Zn–Mg–Cu–Sc–Zr Aluminum Alloys

In this study, the influence of Er addition on the microstructure, type transformation of second phases, and corrosion resistance of an Al–Zn–Mg–Cu alloy were explored. The results revealed that the added Er element could significantly refine the alloy grains and change the second-phase composition at the grain boundary of the alloy. In the as-cast state, the Er element significantly enhanced the corrosion resistance of the alloy due to its refining effect on the grains and second phases at the grain boundary. The addition of the alloying element Er to the investigated alloy changed the type of corrosion attack on the alloy’s surface. In the presence of Er, the dominant type of corrosion attack is pitting corrosion, while the alloy without Er is prone to intergranular corrosion attack. After a solution treatment, the Al₈Cu₄Er phase was formed, in which the interaction with the Cu element and the competitive growth relation to the Al₃Er phase were the key factors influencing the corrosion resistance of the alloy. The anodic corrosion mechanism of the Al₈Cu₄Er and Al₃Er phases evidently lowered the alloy corrosion rate, and the depth of the corrosion pit declined from 197 μm to 155 μm; however, further improvement of corrosion resistance was restricted by the morphology and size of the Al₈Cu₄Er phase after its formation and growth; therefore, adjusting the matching design of the Cu and Er elements can allow Er to improve the corrosion resistance of the Al–Zn–Mg–Cu aluminum alloy to the greatest extent.     

Effect of Heat Treatment on the Mechanical and Corrosion Properties of Mg–Zn–Ga Biodegradable Mg Alloys

Mg alloys have mechanical properties similar to those of human bones, and have been studied extensively because of their potential use in biodegradable medical implants. In this study, the influence of different heat treatment regimens on the microstructure and mechanical and corrosion properties of biodegradable Mg–Zn–Ga alloys was investigated, because Ga is effective in the treatment of disorders associated with accelerated bone loss. Solid–solution heat treatment (SSHT) enhanced the mechanical properties of these alloys, and a low corrosion rate in Hanks’ solution was achieved because of the decrease in the cathodic-phase content after SSHT. Thus, the Mg–4 wt.% Zn–4 wt.% Ga–0.5 wt.% Y alloy after 18 h of SSHT at 350 °C (ultimate tensile strength: 207 MPa; yield strength: 97 MPa; elongation at fracture: 7.5%; corrosion rate: 0.27 mm/year) was recommended for low-loaded orthopedic implants.     

The Effect of Heat Treatment on the Tribological Properties and Room Temperature Corrosion Behavior of Fe–Cr–Al-Based OPH Alloy

The microstructure, mechanical, tribological, and corrosion properties of Fe–Cr–Al–Y-based oxide-precipitation-hardened (OPH) alloy at room temperature are presented. Two OPH alloys with a composition of 0.72Fe–0.15Cr–0.06Al–0.03Mo–0.01Ta–0.02Y₂O₃ and 0.03Y₂O₃ (wt.%) were prepared by mechanical alloying with different milling times. After consolidation by hot rolling, the alloys presented a very fine microstructure with a grain size of approximately 180 nm. Such a structure is relatively brittle, and its mechanical properties are enhanced by heat treatment. Annealing was performed at three temperatures (1000 °C, 1100 °C, and 1200 °C), with a holding time from 1 to 20 h. Tensile testing, wear testing, and corrosion testing were performed to evaluate the effect of heat treatment on the behavior and microstructural properties. The grain size increased almost 10 times by heat treatment, which influenced the mechanical properties. The ultimate tensile strength increased up to 300% more compared to the initial state. On the other hand, heat treatment has a negative effect on corrosion and wear resistance.     

The Effect of Zn and Zn–WO3 Composites Nano-Coatings Deposition on Hardness and Corrosion Resistance in Steel Substrate

Pure Zn (Zinc) and its Zn–WO₃ (Zinc–Tungsten trioxide) composite coatings were deposited on mild steel specimens by applying the electrodeposition technique. Zn–WO₃ composites were prepared for the concentration of 0.5 and 1.0 g/L of particles. The influence of WO₃ particles on Zn deposition, the surface morphology of composite, and texture co-efficient were analyzed using a variety of techniques, such as X-ray diffraction (XRD) and scanning electron microscopy (SEM) with Energy Dispersive X-ray analysis (EDX). Higher corrosion resistance and microhardness were observed on the Zn–WO₃ composite (concentration of 1.0 g/L). The higher corrosion resistance and microhardness of 1.0 g/L Zn–WO₃ nanocomposite coatings effectively protect the steel used for the manufacture of products, parts, or systems from chemical or electrochemical deterioration in industrial and marine ambient environments.     

Properties of WC–10%Co–4%Cr Detonation Spray Coating Deposited on the Al–4%Cu–1%Mg Alloy

One of the methods of local improvement of the wear resistance of aluminum alloy parts is the deposition of hard tungsten carbide-based coatings on the surfaces subjected to intense external influence. This paper is devoted to the characterization of the WC–10Co–4Cr (wt.%) coating deposited on an Al–4Cu–1Mg (wt.%) alloy by the detonation spray method. In comparison with the common thermal spray techniques like High Velocity Oxygen Fuel (HVOF) or Atmospheric Plasma Spraying (APS), the heat input delivered to the substrate during detonation spray is significantly lower, that is especially important in case of coating deposition on aluminum alloys. The paper presents the results of morphology investigation, microstructure, phase composition, microhardness, and cohesive strength of deposited carbide-based detonation spray coating. Results showed that the coating has a porosity less than 0.5% and the carbide grain refinement down to the submicron size during coating deposition was detected. According to the investigation, the variation of spraying distance from 270 to 230 mm does not influence on the coating microstructure and composition.     

The Use of ZrO2 Waste for the Electrolytic Production of Composite Ni–P–ZrO2 Powder

Ni–P–ZrO₂ composite powder was obtained from a galvanic nickel bath with ZrO₂ powder. Production was conducted under galvanostatic conditions. The Ni–P–ZrO₂ composite powder was characterized by the presence of ZrO₂ particles covered with electrolytical nanocrystalline Ni–P coating. The chemical composition (XRF method), phase structure (XRD method) and morphology (SEM) of Ni–P–ZrO₂ and the distribution of elements in the powder were all investigated. Based on the analyses, it was found that the obtained powder contained about 50 weight % Zr and 40 weight % Ni. Phase structure analysis showed that the basic crystalline component of the tested powder is a mixed oxide of zirconium and yttrium Zr_0.92Y_0.08O_1.96. In addition, the sample contains very large amounts of amorphous compounds (Ni–P). The mechanism to produce the composite powder particles is explained on the basis of Ni²⁺ ions adsorption process on the metal oxide particles. Current flow through the cell forces the movement of particles in the bath. Oxide grains with adsorbed nickel ions were transported to the cathode surface. Ni²⁺ ions were discharged. The oxide particles were covered with a Ni–P layer and the heavy composite grains of Ni–P–ZrO₂ flowed down to the bottom of the cell.     

Corrosion Behavior of Candidate Functional Materials for Molten Salts Reactors in LiF–NaF–KF Containing Actinide Fluoride Imitators

Molten fluorides of alkali metals are considered a technological medium for molten salt reactors (MSRs). However, these media are known to be extremely corrosive. The successful implementation of high-temperature technological devices using molten alkali metal fluorides requires the selection of such structural materials that have high corrosion resistance in melts with compositional characteristic of MSRs. In this research, the corrosion behavior of 12Cr18Ni10Ti steel, the alloy Ni60Cr20Mo15, and the alloy Monel 404 (Ni50Cu50) was investigated in the LiF–NaF–KF eutectic melt, containing additions of CeF₃ and NdF₃ from 0 to 5 wt.% as imitator fluorides of actinides in an inert argon atmosphere at 550 °C for 100 h. Gravimetry, energy-dispersive X-ray (EDX) microanalysis of surfaces and cross-section of samples, and ICP-MS were used to establish the corrosion behavior of the investigated alloys. Corrosion resistance of the studied materials was found to decrease in a row from Monel 404 > Hastelloy C2000 > 12Cr18Ni10Ti. The addition of cerium fluoride into the melt resulted in the additional etching of the alloy surface. The addition of neodymium fluoride resulted in the formation of the point/inter-crystalline corrosion damages in the sample bulk. The samples of steel 12Cr18Ni10Ti were subjected to local cracking corrosion. The austenitic nickel-based alloys suffered specific local corrosion with formation of subsurface voids. Excellent corrosion resistance of the Monel alloy under the test conditions was found.     

The Effect of (Mg,Zn)12Ce Phase Content on the Microstructure and the Mechanical Properties of Mg–Zn–Ce–Zr Alloy

The quantitative study of rare earth compounds is important for the improvement of existing magnesium alloy systems and the design of new magnesium alloys. In this paper, the effective separation of matrix and compound in Mg–Zn–Ce–Zr alloy was achieved by a low-temperature chemical phase separation technique. The mass fraction of the (Mg, Zn)₁₂Ce compound was determined and the effect of the (Mg, Zn)₁₂Ce phase content on the heat deformation organization and properties was investigated. The results show that the Mg–Zn–Ce compound in both the as-cast and the homogeneous alloys is (Mg, Zn)₁₂Ce. (Mg, Zn)₁₂Ce phase formation depends on the content and the ratio of Zn and Ce elements in the initial residual melt of the eutectic reaction. The Zn/Ce mass ratios below 2.5 give the highest compound contents for different Zn contents, 5.262 wt.% and 7.040 wt.%, respectively. The increase in the amount of the (Mg, Zn)₁₂Ce phase can significantly reduce the critical conditions for dynamic recrystallization formation. Both the critical strain and the stress decrease with increasing rare earth content. The reduction of the critical conditions and the particle-promoted nucleation mechanism work together to increase the amount of dynamic recrystallization. In addition, it was found that alloys with 6 wt.% Zn elements tend to undergo a dynamic recrystallization softening mechanism, while alloys with 3 wt.% Zn elements tend to undergo a dynamic reversion softening mechanism.     

Effect of Temperature on the Corrosion Behavior and Corrosion Resistance of Copper–Aluminum Laminated Composite Plate

In this paper, the effect of temperature on the corrosion behavior and corrosion resistance of the copper–aluminum laminated composite plates were investigated by salt-spray corrosion, potential polarization curve and electrochemical impedance spectroscopy. Moreover, the microstructure of the copper–aluminum laminated composite plate after salt-spray corrosion was observed by scanning electron microscope, and X-ray photoelectron spectroscopy was used to study the composition of corrosion product. The results revealed that the corrosion products of the copper–aluminum laminated composite plate were Al₂O₃ and AlOOH. Due to the galvanic corrosion of the copper–aluminum laminated composite plate, the cathode underwent oxygen absorption corrosion during the corrosion process; therefore, the presence of moisture and the amount of dissolved oxygen in the corrosive environment had a great influence on the corrosion process. The increasing temperature would evaporate a large amount of moisture, resulting in the corrosion product—aluminum oxide dehydrated and covered the surface of the material in the process of salt-spray corrosion, which played a role in protecting the material. Therefore, the corrosion resistance of the copper–aluminum laminated composite plate first decreased and then increased. In the salt-spray corrosion environment, the corrosion resistance of the copper–aluminum laminated composite plate reached the lowest at 45 °C, and its corrosion rate was the fastest, at 0.728 g/m²·h. The electrochemical corrosion occurred in the solution, and the impact was small; however, in addition to the protective corrosion products, the ion mobility in the solution also had a certain influence on the corrosion rate, and the ionic activity increased with the increase of temperature. Therefore, the corrosion resistance of the copper–aluminum laminated composite plate gradually decreased as the temperature increased, and its corrosion resistance was the worst at 50 °C.     

Biological Safety Evaluation and Surface Modification of Biocompatible Ti–15Zr–4Nb Alloy

We performed biological safety evaluation tests of three Ti–Zr alloys under accelerated extraction condition. We also conducted histopathological analysis of long-term implantation of pure V, Al, Ni, Zr, Nb, and Ta metals as well as Ni–Ti and high-V-containing Ti–15V–3Al–3Sn alloys in rats. The effect of the dental implant (screw) shape on morphometrical parameters was investigated using rabbits. Moreover, we examined the maximum pullout properties of grit-blasted Ti–Zr alloys after their implantation in rabbits. The biological safety evaluation tests of three Ti–Zr alloys (Ti–15Zr–4Nb, Ti–15Zr–4Nb–1Ta, and Ti–15Zr–4Nb–4Ta) showed no adverse (negative) effects of either normal or accelerated extraction. No bone was formed around the pure V and Ni implants. The Al, Zr, Nb, and Ni–Ti implants were surrounded by new bone. The new bone formed around Ti–Ni and high-V-containing Ti alloys tended to be thinner than that formed around Ti–Zr and Ti–6Al–4V alloys. The rate of bone formation on the threaded portion in the Ti–15Zr–4Nb–4Ta dental implant was the same as that on a smooth surface. The maximum pullout loads of the grit- and shot-blasted Ti–Zr alloys increased linearly with implantation period in rabbits. The pullout load of grit-blasted Ti–Zr alloy rods was higher than that of shot-blasted ones. The surface roughness (Ra) and area ratio of residual Al₂O₃ particles of the Ti–15Zr–4Nb alloy surface grit-blasted with Al₂O₃ particles were the same as those of the grit-blasted Alloclassic stem surface. It was clarified that the grit-blasted Ti–15Zr–4Nb alloy could be used for artificial hip joint stems.     

Microgalvanic Corrosion of Mg–Ca and Mg–Al–Ca Alloys in NaCl and Na2SO4 Solutions

As a kind of potential biomedical material, Mg–Ca alloy has attracted much attention. However, the role of Ca-containing intermetallics in microgalvanic corrosion is still controversial. In 0.6 mol/L NaCl and Na₂SO₄ solutions, the microgalvanic corrosion behavior of the second phase and Mg matrix of Mg–Ca and Mg–Al–Ca alloys was examined. It was confirmed that the Mg₂Ca phase acts as a microanode in microgalvanic corrosion in both NaCl and Na₂SO₄ solutions, with the Mg matrix acting as the cathode and the Al₂Ca phase acting as the microcathode to accelerate corrosion of the adjacent Mg matrix. It was also found that Cl⁻ and SO₄²⁻ have different sensibilities to microgalvanic corrosion.     

Wear and Corrosion Resistance of AlSi10Mg–CP–Ti Metal–Metal Composite Materials Produced by Electro-Sinter-Forging

Metal–metal composites are a class of composite materials studied for their high ductility and strength, but their potential applications are currently limited by the complex manufacturing processes involved. Electro-sinter-forging (ESF) is a single-pulse electro discharge sintering technique that proved its effectiveness in the rapid sintering of several metals, alloys, and composites. Previous studies proved the processability of Ti and AlSi10Mg by ESF to produce metal–metal composites and defined a correlation between microstructure and processing parameters. This paper presents the wear and corrosion characterizations of two metal–metal composites obtained via ESF with the following compositions: 20% Ti/80% AlSi10Mg and 20% AlSi10Mg/80% Ti. The two materials showed complementary resistance to wear and corrosion. A higher fraction of AlSi10Mg is responsible for forming a protective tribolayer in dry-sliding conditions, while a higher fraction of Titanium confers improved corrosion resistance due to its higher corrosion potential.     

Characterization of W–Cr Metal Matrix Composite Coatings Reinforced with WC Particles Produced on Low-Carbon Steel Using Laser Processing of Precoat

The paper presents the study results of laser processing of precoat applied on C30 steel. The precoat consisted of powder mixtures with a binder in the form of water glass. Tungsten powder, chromium, and tungsten carbide (WC) were used to produce the precoat. The laser processing was carried out using a Yb:YAG disc laser with a rated power of 1 kW. Constant producing parameters (power of laser beam, 600 W; laser beam scanning rate, 400 mm/min) were applied. Chemical composition of the precoat was a variable parameter in coating production. A mixture consisting of 50% W and 50% Cr as a metal matrix was prepared. Subsequently, WC particles in weight ratios of 25%, 50%, and 75% were added to matrix. As a result, W–Cr metal matrix composite coatings reinforced with WC particles were formed. This study focused on investigation of microstructure, microhardness, phase, and chemical composition as well as corrosion and wear resistance, of the newly formed W–Cr/WC coatings. An instrumented nanoindentation test was also used in this study. As a result of laser beam action, the newly formed coatings had an interesting microstructure and good properties which were improved in comparison to substrate material. It is anticipated that the resulting coatings, depending on the treatment parameters (e.g., W–Cr/WC powder mixture) used, can be successfully applied to metal forming or foundry tools.     

Fabrication of Ni–Cu–W Graded Coatings by Plasma Spray Deposition and Laser Remelting

In this study, Ni–Cu–W graded coatings are produced by atmospheric plasma spraying and subsequently remelted by laser. The surface morphology, hardness, compositional fluctuations and corrosion resistance of the Ni–Cu–W coating are investigated. The coatings after laser remelting are densified and become more homogenous with an excellent corrosion resistance and high hardness, which can be used to explore the new materials.     

Effect of Ga on the Oxide Film Structure and Oxidation Resistance of Sn–Bi–Zn Alloys as Heat Transfer Fluids

The effect of gallium on the oxide film structure and overall oxidation resistance of low melting point Sn–Bi–Zn alloys was investigated under air atmosphere using thermogravimetric analyses. The liquid alloys studied had a Ga content of 1–7 wt.%. The results showed that the growth rates of the surface scale formed on the Sn–Bi–Zn–Ga alloys conformed to the parabolic law. The oxidation resistance of Sn–Bi–Zn alloys was improved by Ga addition and the activation energies increased from 12.05 kJ∙mol⁻¹ to 22.20 kJ∙mol⁻¹. The structure and elemental distribution of the oxide film surface and cross-section were found to become more complicated and denser with Ga addition. Further, the results of X-ray photoelectron spectroscopy and X-ray diffraction show that Ga elements accumulate on the surface of the liquid metal to form oxides, which significantly slowed the oxidation of the surface of the liquid alloy.     

Effect of Silicon on Dynamic/Static Corrosion Resistance of T91 in Lead–Bismuth Eutectic at 550 °C

The 9–12% Cr ferritic–martensitic heat-resistant steel is the main candidate structural material for the Lead-cooled Faster Reactor. The lower Gibbs free energy change of Si oxide can promote the formation of a stable oxide layer, which can improve the corrosion resistance of the material. Therefore, it is of great significance to study the effect of silicon (Si) on the corrosion resistance of T91 steel in lead–bismuth eutectic (LBE). The corrosion resistance of T91 steel with Si contents of 0.5 wt.%, 1.3 wt.%, and 2.0 wt.%, both in dynamic and static LBE at 550 °C, was investigated. The microstructure was analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM), while the oxide films were characterized by electron probe microanalysis (EPMA). Results show that the addition of Si is conducive to improving the corrosion resistance of T91 steel in LBE. T91 steel with high Si content has a thinner and more stable oxide film. The change of Si content can change the contact angle between the steel and LBE, and the contact angle is the largest when the Si content is 1.3 wt.%. The Si-rich oxide layer is usually located in the inner oxide layer, which promotes the formation of a Cr oxide layer located in the internal oxidation zone (IOZ). Si will not enter the precipitated phase, but only change the ferrite content. The oxidation model of T91 steel containing Si in LBE was also proposed.     

Application of BP Artificial Neural Network in Preparation of Ni–W Graded Coatings

The internal stress difference between soft-ductile aluminum alloy substrate and hard-brittle Ni–W alloy coating will cause stress concentration, thus leading to the problem of poor bonding force. Herein, this work prepared the Ni–W graded coating on aluminum alloy matrix by the pulse electrodeposition method in order to solve the mechanical mismatch problem between substrate and coatings. More importantly, a backward propagation (BP) neural network was applied to efficiently optimize the pulse electrodeposition process of Ni–W graded coating. The SEM, EDS, XRD, Vickers hardness tester and Weighing scales are used to analyze the micromorphology, chemical element, phase composition, and micro hardness as well as oxidation weight increase, respectively. The results show that the optimal process conditions with BP neural network are as follows: the bath temperature is 30 °C, current density is 15 mA/cm² and duty cycle is 0.3. The predicted value of the model agrees well with the experimental value curve, the relative error is minor. The maximum error is less than 3%, and the correlation coefficient is 0.9996. The Ni–W graded coating prepared by BP neural network shows good bonding with the substrate which has flat and smooth interface. The thickness of the coating is about 136 μm, which slows down the oxidation of the substrate and plays an effective role in protecting the substrate.     

Investigation on Microstructure,Mechanical and Wear Properties of HVOF Sprayed Composite Coatings (WC–Co + CR) On Ductile Cast Iron

Recent work indicates that the high-velocity oxy-fuel (HVOF) thermal spraying WC–Co coatings have been used to enhance the wear resistance of various engineering components in a variety of industrial environments. In the present work, WC–Co powder, containing Cr particles in an amount of 10%, was deposited on ductile cast iron with the HVOF thermal spray coating technique. An investigation was conducted to determine the role of Cr particles in the WC–Co coating produced with the HVOF technique on microstructure, mechanical, and wear properties in a system of type: WC-Co coating/ductile cast iron. The microstructure of the HVOF-sprayed WC–Co + Cr coating was characterised by light microscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and energy-dispersive X-ray spectroscopy (EDS). The analysis of the microstructure showed the formation of a coating with low porosity, compact structure, and good adhesion to the substrate with a typical lamellar structure composed of fine molten Cr particles and finely fragmented WC grains embedded in a Co matrix, reaching the size of nanocrystalline. The scratch test was applied for the analysis of the adhesion of coatings to the substrate. The erosion behaviour and mechanism of material removal was studied and discussed based on microstructural examinations. Moreover, the results were discussed in relation to the bending strength test, including cracks and delamination in the system of the WC–Co + Cr/ductile cast iron, as microhardness and erosion resistance of the coating. It was found that the addition of Cr particles to the WC–Co powder, which causes hardening of the binder phase is a key influence on increased mechanical and wear properties in the studied system. Additionally, due to the construction of nanostructured coatings, suitable proportion of hard and soft phases, the technique sprayed HVOF coatings have advantageous properties such as high density and good slurry erosion resistance.     

Surface Roughness Analysis and Prediction with an Artificial Neural Network Model for Dry Milling of Co–Cr Biomedical Alloys

The aim of this paper is to conduct an experimental study in order to obtain a roughness (Ra) prediction model for dry end-milling (with an AlTiCrSiN PVD-coated tool) of the Co–28Cr–6Mo and Co–20Cr–15W–10Ni biomedical alloys, a model that can contribute to more quickly obtaining the desired surface quality and shortening the manufacturing process time. An experimental plan based on the central composite design method was adopted to determine the influence of the axial depth of cut, feed per tooth and cutting speed process parameters (input variables) on the Ra surface roughness (response variable) which was recorded after machining for both alloys. To develop the prediction models, statistical techniques were used first and three prediction equations were obtained for each alloy, the best results being achieved using response surface methodology. However, for obtaining a higher accuracy of prediction, ANN models were developed with the help of an application made in LabView for roughness (Ra) prediction. The primary results of this research consist of the Co–28Cr–6Mo and Co–20Cr–15W–10Ni prediction models and the developed application. The modeling results show that the ANN model can predict the surface roughness with high accuracy for the considered Co–Cr alloys.     

Revealing the Effect of Phase Composition and Transformation on the Mechanical Properties of a Cu–6Ni–6Sn–0.6Si Alloy

In the present study, a Cu–6Ni–6Sn–0.6Si alloy is fabricated through frequency induction melting, then subjected to solution treatment, rolling, and annealing. The phase composition, microstructure evolution, and transition mechanism of the Cu–6Ni–6Sn–0.6Si alloy are researched systematically through simulation calculation and experimental characterization. The ultimate as-annealed sample simultaneously performs with high strength and good ductility according to the uniaxial tensile test results at room temperature. There are amounts of precipitates generated, which are identified as belonging to the DO22 and L12 phases through the transmission electron microscope (TEM) analysis. The DO22 and L12 phase precipitates have a significant strengthening effect. Meanwhile, the generation of the common discontinuous precipitation of the γ phase, which is harmful to the mechanical properties of the copper–nickel–tin alloy, is inhibited mightily during the annealing process, possibly due to the existence of the Ni5Si2 primary phase. Therefore, the as-annealed sample of the Cu–6Ni–6Sn–0.6Si alloy possesses high tensile strength and elongation, which are 967 MPa and 12%, respectively.