共查询到20条相似文献，搜索用时 15 毫秒
1.
2.
Tingting Wang Lina Wang Qianqian Lu Zhen Fan 《The Journal of prosthetic dentistry》2019,121(1):156-165
Statement of problem
The grayish appearance of titanium abutments adversely affects peri-implant esthetics in patients with thin mucosa, impacting patient satisfaction with implant-supported restorations in esthetic regions.Purpose
The purpose of this in vitro study was to change the color of titanium alloys with anodic oxidation and to evaluate alterations in the esthetic, physical, and biological properties of the anodized titanium alloys.Material and methods
Pink and yellow titanium alloys produced by anodization were the experimental groups, and the untreated titanium alloy and zirconia were used as the control groups. Pig gingiva was placed on the tested specimens to evaluate the esthetic effect by recording the color change in the gingiva. Physical properties including morphology, chemical composition, roughness, and contact angle were evaluated by scanning electron microscopy, atomic force microscopy, and a contact angle analysis system. Biological properties were evaluated by observing the cell behaviors of human gingival fibroblasts, using scanning electron microscopy, fluorescence microscopy, a live/dead viability assay, and a cell counting assay.Results
A variety of colors can be produced on the surfaces of titanium alloys by anodization at different voltages. Titanium alloys anodized at 60 and 65 V exhibited yellow and pink appearances, respectively. Color differences of gingiva caused by anodized titanium alloys were lower than those of the untreated titanium alloy, but they were higher than those of zirconia. Compared with the untreated titanium alloy, the anodized titanium alloys exhibited grain formation, a lower contact angle, and higher roughness. Cell morphology, proliferation, and viability on surfaces of anodized titanium alloys were similar to those of the untreated titanium alloy but lower than those of zirconia.Conclusions
Anodization could change the color of titanium alloys to pink or yellow at different voltages. Grain formation, roughness, and hydrophilicity were increased after treatment. The esthetics and biocompatibility of anodized titanium alloys were not as good as that of zirconia, but the pink and yellow titanium alloys treated by anodization achieved better gingival esthetics than the untreated titanium alloy. 相似文献3.
Liang Chen Cornelis Johannes Kleverlaan Kunneng Liang Deqin Yang 《The Journal of prosthetic dentistry》2017,117(4):552-558
Statement of problem
Polyvinyl siloxane impression material has been widely used as a lingual matrix for rebuilding missing tooth structure with composite resin. The composite resin is light polymerized in contact with the polyvinyl siloxane impression material. However, polyvinyl siloxane impression material has been shown to interact with other dental materials.Purpose
The purpose of this study was to assess the effect of polyvinyl siloxane impression materials on the polymerization of composite resins by assessing the Vickers microhardness and degree of conversion of polyvinyl siloxane.Material and methods
The composite resins were light polymerized in contact with 3 polyvinyl siloxane impression materials (Flexitime Easy Putty; President Light Body; Xantopren L Blue) (n=8) and in contact with a matrix strip as the control group (n=8). Vickers microhardness and degree of conversion on contact surfaces were measured to evaluate the polymerization of composite resins. The depth of the effect was assessed by Vickers microhardness on section surfaces and observed with scanning electron microscopy. The results were analyzed by 1-way analysis of variance and the post hoc Tukey honest significant differences test (α=.05).Results
The Vickers microhardness and degree of conversion values on the contact surfaces of the experiment groups were significantly lower than those of the control group (P<.05); the Vickers microhardness values on the section surfaces indicated that there was no significant difference at the same depth of different groups (P>.05). The scanning electron microscope observation showed that an approximately 10-μm deep unpolymerized layer was found in the experimental group.Conclusions
Polyvinyl siloxane impression materials have an inhibitory effect on the polymerization of the composite resins, but just limited to within approximately 10 μm from the surface in contact with the impression material. 相似文献4.
Yanan Zhou Ning Li Hongmei Wang Jiazhen Yan Wenbo Liu Sheng Xu 《The Journal of prosthetic dentistry》2019,121(5):848-857
Statement of problem
The metal-ceramic bond strength of dental casting Co-Cr alloys may be improved by the addition of the rare earth element lanthanum (La), but studies are lacking.Purpose
The purpose of this in vitro study was to evaluate the effects of the rare earth element La on the metal-ceramic bond strength of dental casting Co-Cr alloys.Material and methods
Four groups of specimens with different La content (0; 0.02 wt%; 0.04 wt%; 0.06 wt%) were prepared using conventional casting methods. The metal-ceramic bond strength was assessed by using the 3-point bend test. The microstructures were characterized by metallurgical microscopy, scanning electron microscopy, and X-ray diffraction analyses. The morphology and element distribution of metal-ceramic interfaces were evaluated by scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The results of bond strengths were statistically analyzed by the Tukey honest significant difference (HSD) test (α=.05).Results
The specimens showed typical dendritic microstructures, few defects, and island-shaped intermetallic compounds rich in Mo and Cr, mainly consisting of α-Co phase of a face-centered cubic (FCC) structure and ε-Co phase of a close-packed hexagonal (HCP) structure. As the amount of La increased, the thickness of the native oxide layer and the diffusion layer at the interface increased, and the wettability between the oxide layer and the metal matrix improved. The mean ±standard deviation values of the metal-ceramic bond strengths were 28.11 ±4.53 MPa for group 0%, 33.13 ±5.65 MPa for group 0.02%, 37.48 ±7.86 MPa for group 0.04%, and 40.70 ±5.17 MPa for group 0.06%. The statistical analysis indicated that significant differences (P<.05) were observed among all groups tested, except for group 0.04% and 0.06% (P>.05). The debonded surfaces of Co-Cr specimens showed a mixed type of adhesive and cohesive fractures.Conclusions
The microstructures, morphologies, and compositions of oxide films were influenced by the La content, and the La addition could significantly improve the metal-ceramic bond strength of dental casting Co-Cr alloys. 相似文献5.
6.
Jing Zhang Rimei Zhang Guanghui Ren Xiaojie Zhang 《The Journal of prosthetic dentistry》2017,117(2):209-213
This article describes a method that incorporates the solid modeling CAD software Solidworks with a dental milling machine to fabricate individual abutments in house. This process involves creating an implant library with 3-dimensional (3D) models and manufacturing a base, scan element, abutment, and crown anatomy. The 3D models can be imported into any dental computer-aided design and computer-aided (CAD-CAM) manufacturing system. This platform increases abutment design flexibility, as the base and scan elements can be designed to fit several shapes as needed to meet clinical requirements. 相似文献
7.
Alex Leo Sequeira Aparna I. Narayan Vinu Thomas George 《The Journal of prosthetic dentistry》2019,121(5):843-847
Statement of problem
Variation in the baseline mechanical properties of polyamide thermoplastic polymers used in the fabrication of prosthetic dental appliances and the effects of nonaldehyde disinfectants on the mechanical properties of these polymers are unclear.Purpose
The purpose of this in vitro study was to compare the flexural and impact strengths of 2 flexible denture materials (Valplast and Sunflex) and evaluate the effect of 24-hour immersion in nonaldehyde disinfectant (Perform) on their flexural and impact strengths.Material and methods
Of 48 specimens of Valplast and Sunflex, half were immersed in nonaldehyde disinfectant solution containing the active ingredient 2% peroxymonosulfate for 24 hours. Flexural and impact strengths were measured using a universal testing machine. The Student t test with Bonferroni correction was used (α=.008).Results
For the Valplast group, the mean ±standard deviation flexural strength was 27.8 ±0.57 MPa, and the impact strength was 3.5 ±0.98 kJ/m2. For the Sunflex group, the mean flexural strength was 57.4 ±4.09 MPa, and the impact strength was 6.0 ±3.11 kJ/m2. Sunflex showed greater flexural strength (P≤.001) and impact strength (P=.001) than Valplast. A significant increase in the impact strength (P≤.001) but not in the flexural strength of Valplast was observed after exposure to the disinfectant solution. Immersion disinfection had no significant effect on the strength of Sunflex.Conclusions
The flexural and impact strengths of Sunflex were significantly greater than those of Valplast. Immersion disinfection with peroxymonosulfate had no significant effect on Sunflex but increased the impact strength of Valplast. 相似文献8.
Wenhao Li Jingming Liu Su Chen Yao Wang Zhenting Zhang 《The Journal of prosthetic dentistry》2017,117(1):48-54
Statement of problem
Gastroesophageal reflux disease (GERD) is typically diagnosed based on symptoms of regurgitation and heartburn, although it may also manifest as asthma-like symptoms, laryngitis, or dental erosion.Purpose
The purpose of this prospective, cross-sectional study was to assess the prevalence of dental erosion in people with GERD and to evaluate the association between GERD and dental erosion.Material and methods
The presence, severity, and pattern of dental erosion was assessed in 51 participants with GERD and 50 participants without GERD using the Smith and Knight tooth wear index. Medical, dietary, and dental histories were collected by questionnaire. Factors potentially related to dental erosion, including GERD, were evaluated by logistic regression.Results
Dental erosion was observed in 31 (60.8%) participants with GERD and 14 (28%) participants without GERD. Bivariate analysis revealed that participants with GERD were more likely to experience dental erosion (crude odds ratio [cOR]: 2.74; 95% CI: 1.19, 6.32) than participants without GERD. Multivariate analysis also revealed that participants with GERD had a higher risk of dental erosion (adjusted odds ratio [aOR]: 3.97; 95% CI: 1.45, 10.89). Consumption of grains and legumes, the most frequently consumed foods in China, did not correlate with dental erosion. However, carbonated beverage consumption was significantly associated with GERD and dental erosion (aOR: 3.34; 95% CI: 1.01, 11.04; P=.04).Conclusions
GERD was positively correlated with dental erosion. Carbonated beverage consumption can increase the risk of both GERD and dental erosion. 相似文献9.
目的 研究不同热凝义齿基托树脂对基托表面亲水性及力学性能的影响,以提高义齿基托的表面特性及弯曲特性的新思路和新方法。方法 选择平均分子量及平均粒径不同的4种粉剂：D-100M(甲基丙烯酸甲酯聚合物粉）,聚甲基丙烯酸甲酯聚合(D-250M）,聚甲基丙烯酸甲酯/丙烯酸乙酯共聚物(D-300）,聚甲基丙烯酸乙酯聚合物(D-250E）,作为研究对象,将各组粉剂和4种单体(MMA,i-BMA,EHMA,HEMA）分别配对聚合成15种不同材料的试件,进行周期性浸泡,随后置于恒温干燥箱0、14、30、90、180、360天后,测定表面接触角及弯曲性能。结果 浸泡前各组试件之间的差异有统计学意义(P<0.05）。浸泡后各材料之间的接触角变化显著不同;弯曲强度及弯曲弹性模量的差异有统计学意义(P<0.05）。随着时间推移,甲基丙烯酸甲酯组(MMA）的弯曲强度显著高于其他组(P<0.05）;单体MMA和EHMA+HEMA组浸泡至360天时弯曲强度无显著变化;其余组的样本浸泡至30天后弯曲强度明显上升。结论 适当组成成分的搭配对热凝义齿基托的表面亲水性、弯曲强度及弯曲弹性模量有很大影响,恰当的组合能改进热凝义齿基托的表面特性及力学性能。 相似文献
10.
Statement of problem
Studies of the color stability, relative translucency, and surface roughness of newly introduced computer-assisted design and computer-assisted manufacturing (CAD-CAM) prepolymerized poly(methyl methacrylate) (PMMA) denture base materials are lacking.Purpose
The purpose of this in vitro study was to evaluate the color stability, relative translucency, and surface roughness of conventional and different prepolymerized CAD-CAM PMMA denture base materials after coffee thermocycling (CTC).Material and methods
Six disk-shaped specimens (10×2 mm) were prepared from 3 different brands of prepolymerized CAD-CAM PMMA and a conventional heat-polymerized PMMA denture base material (N=24). Specimens were polished conventionally in 2 stages. The specimens were subjected to 5000 coffee thermocycles. The surface roughness (Ra) of each specimen was measured 3 times before and after CTC, using a contact profilometer, and the mean roughness (Ra) values were calculated. The color coordinates of the specimens were determined by using a noncontact spectroradiometer, and color differences and relative translucency parameter (RTP) values were calculated by using CIEDE2000 color difference and RTPCIEDE2000 formulas. ANOVA was used to analyze surface roughness values, CIEDE2000 color differences, and RTP values (α=.05).Results
CTC did not change the color of the tested materials. However, with regard to relative translucency, 2-way ANOVA revealed a significant interaction between the material and CTC (P=.011). Also, although CTC increased the surface roughness of all tested materials (P=.031), Ra values were lower than the plaque accumulation threshold of Ra=0.2 μm.Conclusions
Mean color changes in all materials were clinically imperceptible after 5000 coffee thermocycles. One tested material had significantly lower relative translucency than other materials before and after CTC. The surface roughness values of all tested denture base materials were below the plaque accumulation threshold. 相似文献11.
Statement of problem
In addition to the original abutments provided by implant companies, compatible computer-aided design and computer-aided manufacturing (CAD-CAM) abutments are also available from different manufacturers. However, the combination of abutments and implant systems from different manufacturers may lead to mechanical problems between components. Little has been reported on the clinical performance of this treatment option.Purpose
The purpose of this retrospective case series was to evaluate the outcome of compatible CAD-CAM titanium abutments (TiAs) for posterior single-implant tooth replacement (PSITR) up to 6 years after insertion.Material and methods
Eighty-one patients (34 men, 47 women) who received PSITR restored with compatible CAD-CAM TiAs and had a final recall examination between May 2014 and April 2015 were included in this study. Clinical and radiographic examinations were documented. Retrospective evaluation of the patient records was also performed. Correlations between bone-level changes and variables were calculated using the Spearman correlation.Results
Implant and prosthesis survival rates were 100%. Twenty technical complications were observed, including 9 decementations of the crown, 6 screw loosenings, and 5 ceramic fractures. Periimplant mucositis was diagnosed in 36 patients (44.4%) and periimplantitis in 6 patients (7.4%). Correlation analysis showed a significant effect of the extent of periodontal bone loss of the remaining teeth on the marginal bone-level changes around implants (r=0.548, P<.001).Conclusions
Compatible CAD-CAM TiAs provide a viable treatment option for PSITR. However, in light of relatively high screw-loosening and decementation rates, choosing appropriate cements and abutment manufacturers is essential to improve the clinical performance of this treatment option. 相似文献12.
Young S. Kang Frederick Rueggeberg Van Ramos 《The Journal of prosthetic dentistry》2017,117(2):266-270
Statement of problem
Polyvinyl siloxane (PVS) impression materials must be cold disinfected before cast pouring to prevent cross-contamination among personnel and patients. However, disinfection may affect the ability of PVS impression materials to provide bubble-free stone surfaces because of the removal of surfactants.Purpose
The purpose of this in vitro study was to compare the water contact angles of a PVS impression material treated with either a quaternary ammonium-based (QAB) (DisCide Ultra) or a chlorine-based (CLB) (Dispatch) disinfectant for various exposure times. No disinfection and acetone-immersed (total surfactant removal) specimens were used as positive and negative controls. An additional purpose was to measure changes in the contact angles of the disinfected PVS impression material after applying a topical wetting agent.Material and methods
Flat and disk-shaped PVS specimens (n=5/test condition) were fabricated and subsequently exposed to disinfectants for different times (1 minute, 5 minutes, 30 minutes, 6 hours, and 24 hours). After disinfection, the contact angle with distilled water was determined over a 3-minute period using dynamic contact analysis. The same contact angle measurements were repeated after a wetting agent was applied to the previously disinfected specimens. Contact angles were statistically compared using 2-way ANOVA. The Sidak post hoc test was used to perform pairwise simple contrast and effect comparisons (α=.05).Results
The contact angle increased directly with disinfectant contact time. For the CLB product, the contact angle after 30-minute disinfection was not significantly different from that of 1 minute disinfection (P>.05). For the QAB product, exceeding 5-minutes of disinfection resulted in a significantly greater contact angle (P<.001). The application of a wetting agent made the disinfected PVS specimens less hydrophobic.Conclusions
A QAB disinfectant product is more effective at removing surfactant than a CLB disinfectant product. Therefore, a CLB disinfectant provides more working time and control. A wetting agent can reduce the hydrophobicity of a disinfected impression material if the duration of cold disinfection is less than 6 hours. 相似文献13.
Yanning Chen Chenmin Yao Cui Huang Yake Wang 《The Journal of prosthetic dentistry》2019,121(3):549.e1-549.e7
Statement of problem
Although newly developed photoinitiators can make up for the limitations of camphorquinone, their absorption spectra are different. However, little attention has been paid to the compatibility of available wavelength spectra of light-polymerization units (LPUs) and photoinitiators within resin cements.Purpose
The purpose of this in vitro study was to evaluate the effect of monowave and polywave light-emitting diode (LED) units on the adhesion of dual-polymerizing self-adhesive resin cements to monolithic zirconia.Material and methods
Monowave LPUs and polywave LPUs were chosen to polymerize 2 dual-polymerizing self-adhesive resin cements. Ninety-six zirconia disks were randomly divided into 4 groups as different combinations of LPUs and resin cements, namely ES-U200, BS-U200, ES-SC, and BS-SC. Resin cements were adhered to zirconia disks, and the microshear bond strength (μSBS) test was conducted after 24 hours of H2O storage (24 h) and 10?000 thermocycles (10k/TC). Failure modes were examined by stereomicroscopy and scanning electron microscopy (SEM). The degree of conversion (DC) was tested both immediately and 24 hours later. In statistical analyses, 2-way ANOVA and the Tukey honestly significant difference post hoc test were performed for μSBS and DC results, and chi-square test was performed for failure mode analysis (α=.05 for all tests).Results
The 2-way ANOVA demonstrated that different combinations of LPUs and resin cements, as well as different artificial aging levels, significantly influenced microshear bond strength values (P<.001). The interactions between 2 factors were also significant (P<.001). The BS-SC group possessed relatively high bond strength in both 24-hour and 10k/TC aging levels. For the same resin cement, no significant difference was found in the immediate DC (P=.405 for U200 and P=.708 for SC). At 24 hours, DC and BS-U200 values were significantly higher than ES-U200 values (P=.002), whereas BS-SC values were not significantly different from ES-SC values (P=.284).Conclusions
Within the limitation of this in vitro study, the emission spectra of LED units significantly influenced the bond strengths, DC, and failure mode of dual-polymerizing self-adhesive resin cements to zirconia at both immediate and artificial aging levels. The LPU should provide light energy to match the absorption wavelengths of photoinitiators in the resin cements. 相似文献14.
Kanchan P. Dholam Jinesh A. Dugad Karthik M. Sadashiva 《The Journal of prosthetic dentistry》2017,117(4):559-562
Statement of problem
The treatment of oral cancers affects oral functions and quality of life (QOL). Dental rehabilitation is a major step toward enhancing quality of life after controlling the disease. The effects of the disease, treatment, and rehabilitation need to be evaluated to assess oral health-related QOL. The Liverpool Oral Rehabilitation Questionnaire version 3 (LORQv3) and Oral Health Impact Profile-14 (OHIP-14) are specific assessment questionnaires of oral rehabilitation.Purpose
The purpose of this study was to assess the impact of oral rehabilitation on patients with head and neck cancer by using the LORQv3 and OHIP-14 questionnaires and to discover and document specific patient-derived problems related to the issues of oral rehabilitation.Material and Methods
The LORQv3 and OHIP-14 questionnaires were administered to 60 participants with oral cancer, who were in need of oral rehabilitation. They were asked to rate their dental problems on a Likert scale before fabrication of their prostheses (baseline) and at the 3-month follow-up visit after prosthetic rehabilitation. Paired comparison was done using the Wilcoxon signed rank test according to the distribution, and Cronbach alpha was used to assess internal consistency. Subscale scores were determined by mean value (α=.05).Results
For the LORQv3 questionnaire, a 10% to 27% improvement was found in the domain of oral function, and a 20% improvement in orofacial appearance, with improvement in patient satisfaction with the prosthesis. Using the OHIP-14 questionnaire, a 45% to 67% improvement was generally seen in all domains.Conclusions
After assessment using the LORQv3 and OHIP-14 questionnaires, prosthetic rehabilitation was seen to contribute to the betterment of patients with head and neck cancer. 相似文献15.
Statement of problem
Selective laser melting (SLM) has become popular in prosthetic dentistry. However, only limited information is available for the internal adaptation of cobalt-chromium (Co-Cr) posts fabricated by SLM.Purpose
The purpose of this in vitro study was to investigate the internal adaptation of Co-Cr metal posts fabricated by SLM technique.Material and methods
Thirty-six Co-Cr metal posts were fabricated by conventional casting, subtractive computer-aided design and computer-aided manufacturing (CAD-CAM), and additive CAD-CAM, by making an impression from a standardized model of a tooth with a single root canal. Posts and the dies were bonded with cement. Specimens were then sectioned horizontally by using a grinding and polishing machine, and 3 different cross-sections of each post were chosen to represent the apical, middle, and coronal regions. The areas of cement were photographed by using a stereomicroscope at an original magnification of ×32 and measured using image-measuring software. From each group, 1 specimen was randomly selected and observed by using scanning electron microscopy. One-way ANOVA and Tukey honestly significant difference test were performed to identify differences among groups with regard to internal adaptation (α=.05).Result
The internal adaptation of the SLM group did not differ from that of the CAD-CAM milling group at 3 cross-section levels (P>.05). At the apical and coronal cross-section levels, the cement area of SLM group was smaller than that of the cast group (P<.05). However, at the middle cross-section level, the cement area of the cast group was significantly smaller than that of the SLM group (P<.05). Use of scanning electron microscopy showed both the SLM group and the CAD-CAM milling group exhibited homogeneous microstructures. However, the cast group showed a typical discontinuous dendritic solidification microstructure.Conclusions
The internal adaptation of SLM was not inferior to that of the CAD-CAM milling group or the cast group. The SLM technique seems a promising choice for fabricating dental posts. 相似文献16.
Wafa’a R. Al-Magaleh Amal A. Swelem Mohamed H. Abdelnabi Abdulbaset Mofadhal 《The Journal of prosthetic dentistry》2019,121(3):440-446
Statement of problem
The effect of the neutral zone (NZ) technique on different functional aspects (masticatory performance, speech, and muscle activity) has been studied objectively. Subjectively, some studies reported that their participants felt that NZ dentures were more stable, retentive, and comfortable than conventionally fabricated dentures. These studies, however, lacked a measurable assessment scale or a specifically designed questionnaire.Purpose
The purpose of this within-subject, crossover clinical trial was to investigate patient satisfaction levels in edentulous patients after rehabilitation with dentures fabricated using the NZ concept as compared with conventional dentures using a specific, question-oriented patient satisfaction questionnaire.Material and methods
The clinical trial included 52 participants. Each received one set of conventional dentures and another fabricated based on the NZ concept with a 1-month wash-out period. Participants randomly chose 1 of 2 closed opaque envelopes with 2 denture sequences, either conventional then NZ or NZ then conventional. Hence, participants were blinded to the dentures they wore. Patient satisfaction with each denture type was assessed 6 weeks after insertion by a blinded staff member using a 5-scale questionnaire developed for the most important functional aspects (esthetics, masticatory ability, retention, stability, speech, and comfort). The Wilcoxon Signed Rank test was used to compare the satisfaction scores of the 2 denture types (α=.05).Results
Patient satisfaction scores were significantly higher with the NZ dentures than with the conventional dentures in all aspects; P=.001 for question 2 (opinion of denture appearance) and P<.001 for all other questions.Conclusions
NZ dentures offer significantly higher levels of patient satisfaction than conventional dentures in all functional aspects (retention, stability, masticatory ability, and speech) as well as in comfort and appearance. 相似文献17.
Junxin Zhu Qiguo Rong Xiaoyan Wang Xuejun Gao 《The Journal of prosthetic dentistry》2017,117(5):646-655
Statement of problem
How tooth preparation and material type affect the stress distribution of endodontically treated teeth restored with endocrowns remains unclear.Purpose
The purpose of this finite element (FE) study was to determine the influence of the quantity of remaining dental tissues and material type on stress distribution in endodontically treated maxillary premolars using 3-dimensional FE analysis.Material and methods
Five 3-dimensional FE models were constructed on the basis of the restorative methods used and the quantity of preserved tooth tissues: a sound maxillary premolar, an endodontically treated maxillary premolar restored with composite resin, and endodontically treated maxillary premolars restored with endocrowns with thicknesses of 1.0 mm, 2.0 mm, and 3.0 mm. The following endocrown materials were used: Paradigm MZ100, IPS Empress, IPS e.max CAD, and In-Ceram Zirconia. Stress distributions were analyzed under vertical and oblique loads.Results
As the quantity of preserved dental tissues increased, the von Mises stress in dentin decreased, and the peak von Mises strain value of the cement layer increased. When the elastic modulus of the endocrown material increased, the von Mises stress in endocrown and dentin increased, and the peak von Mises strain value of the cement layer decreased.Conclusions
Although the conservative preparation of teeth for endocrowns is likely to protect the residual tooth structure, it may cause future cohesive bonding failure. An increase in the elastic modulus of the material may benefit the durability of bonding between the endocrown and the abutment tooth; however, it may cause fracture of the residual tooth structure. 相似文献18.
19.
Kariem M. Elhelow Yasser E. Al-Thobaiti Abdurabu A. Gomawi 《The Journal of prosthetic dentistry》2018,119(5):848-851
Nonsurgical prosthetic interventions are often proposed after repeated grafts have failed to restore irradiated facial defects. This report describes a facial prosthetic reconstruction following ablative surgery for a sizable facial tumor by using a novel custom-made magnet-bearing substructure, which connected with an exposed part of the mandibular reconstruction plate. The defect involved the entire left lower part of the face and angle of the mentum. This reconstructive technique, together with an added surface texture with hair-like silicone strands, effectively addressed the cosmetic needs of the patient. Magnetic anchorage to an exposed reconstruction plate could be considered an option for retaining facial prostheses. The biomechanical aspects of loading and retention should be addressed before considering this prosthetic option. 相似文献
20.
Bundhit Jirajariyavej Peeraphorn Wanapirom Chuchai Anunmana 《The Journal of prosthetic dentistry》2018,119(5):819-825