Fe–Doped TiO2–Carbonized Medium–Density Fiberboard for Photodegradation of Methylene Blue under Visible Light

Fe–doped titanium dioxide–carbonized medium–density fiberboard (Fe/TiO₂–cMDF) was evaluated for the photodegradation of methylene blue (MB) under a Blue (450 nm) light emitting diode (LED) module (6 W) and commercial LED (450 nm + 570 nm) bulbs (8 W, 12 W). Adsorption under daylight/dark conditions (three cycles each) and photodegradation (five cycles) were separately conducted. Photodegradation under Blue LED followed pseudo-second-order kinetics while photodegradation under commercial LED bulbs followed pseudo-first-order kinetics. Photodegradation rate constants were corrected by subtracting the adsorption rate constant except on the Blue LED experiment due to their difference in kinetics. For 8 W LED, the rate constants remained consistent at ~11.0 × 10⁻³/h. For 12 W LED, the rate constant for the first cycle was found to have the fastest photodegradation performance at 41.4 × 10⁻³/h. After the first cycle, the rate constants for the second to fifth cycle remained consistent at ~28.5 × 10⁻³/h. The energy supplied by Blue LED or commercial LEDs was sufficient for the bandgap energy requirement of Fe/TiO₂–cMDF at 2.60 eV. Consequently, Fe/TiO₂–cMDF was considered as a potential wood-based composite for the continuous treatment of dye wastewater under visible light.     

Effects of TiO2 Nanoparticle Addition on Microstructure and Selected Properties of Ag–xTiO2 Composites

The paper presents the results of a study of the microstructure and selected properties of silver-based composites reinforced with TiO₂ nanoparticles, produced by the powder metallurgy method. Pure silver powders were mixed with TiO₂ reinforcement (5 and 10 wt%) and 5 mm steel balls (100Cr6) for 270 min in a Turbula T2F mixer to produce a homogeneous mixture. The composites were made in a rigid die with a single-action compaction press under a pressure of 400 MPa and 500 MPa and then sintered under nitrogen atmosphere at 900 °C. Additionally, to improve the density and mechanical properties of the obtained sinters, double pressing and double sintering operations were conducted. As a result, compacts with a density of 90–94% were obtained. The microstructure of the sintered compacts consists of uniform grains, and the TiO₂ reinforcement phase particles are located on the grain boundaries. There were no discontinuities at the Ag–TiO₂ contact boundary, which was confirmed by SEM and TEM analysis. The use of a higher pressure had a positive effect on the hardness and flexural strength of the tested materials. It was found that the composites with 5 wt% TiO₂ pressed under 500 MPa are characterized by the highest level of mechanical properties. The hardness of these composites is 57 HB, while the flexural strength is 163 MPa.     

Microstructure and Mechanical Properties of TiN–TiB2–hBN Composites Fabricated by Reactive Hot Pressing Using TiN–B Mixture

In this study, TiN–TiB₂–hBN composite ceramics were prepared via reactive hot pressing using TiN and amorphous B powders as raw materials. Different sintering temperatures and composition ratios were studied. The results show that the 70 vol% TiN–17.6 vol% TiB₂–12.4 vol% hBN ceramic composites obtained ideal comprehensive properties at 1600 °C. The relative density, Vickers hardness, bending strength, and fracture toughness were 99%, 11 GPa, 521 MPa, and 4.22 MPa·m^1/2, respectively. Densification was promoted by the highly active reaction product TiB₂, and the structural defects formed in the grains. Meanwhile, the good interfacial bonding between TiN and TiB₂ grains and the uniform dispersion of ultrafine hBN in the matrix contributed to the excellent bending strength. Moreover, the toughening mechanism of crack deflection and grain pull-out improved the fracture toughness.     

Effect of Bimetallic-Activated Carbon Impregnation on Adsorption–Desorption Performance for Hydrogen Sulfide (H2S) Capture

This study reports on the impregnation of bi-metallic adsorbents based on commercial coconut activated carbon (CAC), surface-modified with metal acetate (ZnAc₂), metal oxide (ZnO and TiO₂), and the basic compound potassium hydroxide (KOH). The morphology of the adsorbents was then characterized with SEM-EDX, the microporosity was determined using Brunauer–Emmett–Teller (BET) analysis, the thermal stability was investigated via thermogravity analysis (TGA), and functional group analysis was undertaken with Fourier-transform infrared (FTIR) spectroscopy. These modified adsorbents were subjected to a real adsorption test for H₂S capture using a 1 L adsorber with 5000 ppm H₂S balanced for N₂, with temperature and pressure maintained at an ambient condition. Adsorption–desorption was carried out in three cycles with the blower temperature varied from 50 °C to 150 °C as the desorption condition. Characterization results revealed that the impregnated solution homogeneously covered the adsorbent surface, effecting the morphology and properties. Based on this study, it was found that ZnAc₂/TiO₂/CAC_DCM showed a significant increase in adsorption capacity with the different temperatures applied for the desorption in the second cycle: 1.67 mg H₂S/g at 50 °C, 1.84 mg H₂S/g at 100 °C, and 1.96 mg H₂S/g at 150 °C. ZnAc₂/ZnO/CAC_DCM seemed to produce the lowest percentage of degradation in the three cycles for all the temperatures used in the adsorption–desorption process. Therefore, ZnAc₂/ZnO/CAC_DCM has the potential to be used and commercialized for biogas purification for H₂S removal.     

Characteristics of Doped TiO2 Nanoparticle Photocatalysts Prepared by the Rotten Egg White

In this study, expired egg white was used as a template, and a sol–gel method was employed to prepare pure-phase TiO₂ nano-powder and mixed-phase powders doped with NaF and NaI. The influences of different calcination temperatures, doping elements, and doping amounts during the preparation process on the photocatalytic performance and activity of the prepared TiO₂ powders were studied. The results of the experiments showed that the F-doped TiO₂ had the highest photocatalytic activity when the doping amount was 1.2%, as examined by EDS, where the sintering temperature was 500 °C. F-doped TiO₂ nanoparticles were also synthesized by the sol–gel method using tetrabutyl titanate and NaF mixed with expired egg white protein as the precursor. The F-TiO₂ photocatalyst was characterized using FE-SEM, HR-TEM, EDS, XPS, and UV-Vis, and the photocatalytic activity was evaluated by photodegradation of methylene blue under visible light. The results showed that doping with F reduced the energy band gap (3.04 eV) of TiO₂, thereby increasing the photocatalytic activity in the visible-light region. The visible-light wavelength range and photocatalytic activity of the catalyst were also affected by the doping amount.     

Closed-Surface Multifunctional Antireflective Coating Made from SiO2 with TiO2 Nanocomposites

An SiO₂-TiO₂ closed-surface antireflective coating was fabricated by the one-dipping method. TiO₂ nanoparticles were mixed with a nanocomposited silica sol, which was composed of acid-catalyzed nanosilica networks and silica hollow nanospheres (HNs). The microstructure of the sol-gel was characterized by transmission electron microscopy. The silica HNs were approximately 40–50 nm in diameter with a shell thickness of approximately 8–10 nm. The branched-chain structure resulting from acidic hydrolysis grew on these silica HNs, and TiO₂ was distributed inside this network. The surface morphology of the coating was measured by field emission scanning electron microscopy and atomic force microscopy. After optimization, transmittance of up to 94.03% was obtained on photovoltaic (PV) glass with a single side coated by this antireflective coating, whose refractive index was around 1.30. The short-circuit current gain of PV module was around 2.14–2.32%, as shown by the current-voltage (IV) curve measurements and external quantum efficiency (EQE) tests. This thin film also exhibited high photocatalytic activity. Due to the lack of voids on its surface, the antireflective coating in this study possessed excellent long-term reliability and robustness in both high-moisture and high-temperature environments. Combined with its self-cleaning function, this antireflective coating has great potential to be implemented in windows and photovoltaic modules.     

Study of Construction and Performance on Photoelectric Devices of Cs–Pb–Br Perovskite Quantum Dot

White LEDs were encapsulated using Cs₄PbBr₆ quantum dots and Gd₂O₃:Eu red phosphor as lamp powder. Under the excitation of a GaN chip, the color coordinates of the W-LED were (0.33, 0.34), and the color temperature was 5752 K, which is close to the color coordinate and color temperature range of standard sunlight. The electric current stability was excellent with an increase in the electric current, voltage, and luminescence intensity of the quantum dots and phosphors by more than 10 times. However, the stability of the quantum dots was slightly insufficient over long working periods. The photocatalytic devices were constructed using TiO₂, CsPbBr₃, and NiO as an electron transport layer, light absorption layer, and catalyst, respectively. The Cs–Pb–Br-based perovskite quantum dot photocatalytic devices were constructed using a two-step spin coating method, one-step spin coating method, and full PLD technology. In order to improve the water stability of the device, a hydrophobic carbon paste and carbon film were selected as the hole transport layer. The TiO₂ layer and perovskite layer with different thicknesses and film forming qualities were obtained by changing the spin coating speed. The influence of the spin coating speed on the device’s performance was explored through SEM and a J–V curve to find the best spin coating process. The device constructed by the two-step spin coating method had a higher current density but no obvious increase in the current density under light, while the other two methods could obtain a more obvious light response, but the current density was very low.     

Synthesis of Si-Based High-Efficiency and High-Durability Superhydrophilic-Underwater Superoleophobic Membrane of Oil–Water Separation

Oil pollution is caused by the frequent discharge of contaminated industrial wastewater and accidental oil spills and is a severe environmental and health concern. Therefore, efficient materials and processes for effective oil–water separation are being developed. Herein, SiO₂-Na₂SiO₃-coated stainless steel fibers (SSF) with underwater superoleophobic and low-adhesion properties were successfully prepared via a one-step hydrothermal process. The modified surfaces were characterized with scanning electron microscopy (SEM), and contact angle measurements to observe the surface morphology, confirm the successful incorporation of SiO₂, and evaluate the wettability, as well as with X-ray diffraction (XRD). The results revealed that SiO₂ nanoparticles were successfully grown on the stainless-steel fiber surface through the facile hydrothermal synthesis, and the formation of sodium silicate was detected with XRD. The SiO₂-Na₂SiO₃-coated SSF surface exhibited superior underwater superoleophobic properties (153–162°), super-hydrophilicity and high separation efficiency for dichloromethane–water, n-hexane–water, tetrachloromethane–water, paroline–water, and hexadecane–water mixtures. In addition, the as-prepared SiO₂-Na₂SiO₃-coated SSF demonstrated superior wear resistance, long-term stability, and re-usability. We suggest that the improved durability may be due to the presence of sodium silicate that enhanced the membrane strength. The SiO₂-Na₂SiO₃-coated SSF also exhibited desirable corrosion resistance in salty and acidic environments; however, further optimization is needed for their use in basic media. The current study presents a novel approach to fabricate high-performance oil–water separation membranes.     

Effect of Particle Size on the Mechanical Properties of TiO2–Epoxy Nanocomposites

This study investigated the effects of the packing density and particle size distribution of TiO₂ nanoparticles on the mechanical properties of TiO₂–epoxy nanocomposites (NCs). The uniform dispersion and good interfacial bonding of TiO₂ in the epoxy resin resulted in improved mechanical properties with the addition of nanoparticles. Reinforcement nano-TiO₂ particles dispersed in deionized water produced by three different ultrasonic dispersion methods were used; the ultrasonication effects were then compared. The nano-TiO₂ suspension was added at 0.5–5.0 wt.%, and the mechanical and thermal properties of TiO₂–epoxy NCs were compared using a universal testing machine, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), and differential scanning calorimetry (DSC). The tensile strength of the NCs was improved by the dispersion strengthening effect of the TiO₂ nanoparticles, and focused sonication improved the tensile strength the most when nano-TiO₂ suspensions with a particle size of 100 nm or smaller were used. Thus, the reinforcing effect of TiO₂ nanoparticles on the epoxy resin was observed, and the nano-TiO₂ suspension produced by focused sonication showed a more distinct reinforcing effect.     

Effect of Al2TiO5 Content and Sintering Temperature on the Microstructure and Residual Stress of Al2O3–Al2TiO5 Ceramic Composites

A series of Al₂O₃–Al₂TiO₅ ceramic composites with different Al₂TiO₅ contents (10 and 40 vol.%) fabricated at different sintering temperatures (1450 and 1550 °C) was studied in the present work. The microstructure, crystallite structure, and through-thickness residual stress of these composites were investigated by scanning electron microscopy, X-ray diffraction, time-of-flight neutron diffraction, and Rietveld analysis. Lattice parameter variations and individual peak shifts were analyzed to calculate the mean phase stresses in the Al₂O₃ matrix and Al₂TiO₅ particulates as well as the peak-specific residual stresses for different hkl reflections of each phase. The results showed that the microstructure of the composites was affected by the Al₂TiO₅ content and sintering temperature. Moreover, as the Al₂TiO₅ grain size increased, microcracking occurred, resulting in decreased flexure strength. The sintering temperatures at 1450 and 1550 °C ensured the complete formation of Al₂TiO₅ during the reaction sintering and the subsequent cooling of Al₂O₃–Al₂TiO₅ composites. Some decomposition of AT occurred at the sintering temperature of 1550 °C. The mean phase residual stresses in Al₂TiO₅ particulates are tensile, and those in the Al₂O₃ matrix are compressive, with virtually flat through-thickness residual stress profiles in bulk samples. Owing to the thermal expansion anisotropy in the individual phase, the sign and magnitude of peak-specific residual stress values highly depend on individual hkl reflection. Both mean phase and peak-specific residual stresses were found to be dependent on the Al₂TiO₅ content and sintering temperature of Al₂O₃–Al₂TiO₅ composites, since the different developed microstructures can produce stress-relief microcracks. The present work is beneficial for developing Al₂O₃–Al₂TiO₅ composites with controlled microstructure and residual stress, which are crucial for achieving the desired thermal and mechanical properties.     

Performance of Sprayed PVDF-Al2O3 Composite Coating for Industrial and Civil Applications

Because of their great water repellency, Superhydrophobic coatings have a major impact on a variety of industrial applications. The current study’s key originality is the development of low-cost, stable, superhydrophobic, and corrosion-resistant composite coatings. In the present work, polyvinylidene fluoride (PVDF)/Al₂O₃ composite coatings were produced using the spray technique to investigate the wettability and corrosion behavior of the coated materials for industrial and civil applications. PVDF was mixed with various concentrations of Al₂O₃ nanoparticles, and the mixture was sprayed onto steel, aluminum, and glass substrates. The wettability and morphology of the coated surfaces were investigated using the sessile droplet method and scanning electron microscopy, respectively. The corrosion resistance of bare substrates was compared to that of those coated with PVDF alone and those coated with PVDF/Al₂O₃ nanoparticles using Tafel polarization techniques. The force of adhesion between the coat and the substrates was measured in pounds per square inch. A nanoindentation test was also used to measure the hardness of the coating layer. The PVDF/Al₂O₃ coated steel showed a significantly higher water contact angle and lower contact angle hysteresis, reaching 157 ± 2° and 7 ± 1°, respectively, compared to the coated aluminum and glass substrates. Corrosion test results showed that the superhydrophobic PVDF/Al₂O₃ coatings had a much higher corrosion protection efficiency for steel and aluminum than that of the PVDF ones. The PVDF/Al₂O₃ coated substrates showed moderate but still acceptable adhesion between the coating layer and the substrates. Moreover, the PVDF/Al₂O₃ coatings had much better mechanical properties than the PVDF only coatings. Such type of coating could be a promising candidate for possible industrial and civil applications.     

Precipitation Hardening at Elevated Temperatures above 400 °C and Subsequent Natural Age Hardening of Commercial Al–Si–Cu Alloy

The precipitation of intermetallic phases and the associated hardening by artificial aging treatments at elevated temperatures above 400 °C were systematically investigated in the commercially available AC2B alloy with a nominal composition of Al–6Si–3Cu (mass%). The natural age hardening of the artificially aged samples at various temperatures was also examined. A slight increase in hardness (approximately 5 HV) of the AC2B alloy was observed at an elevated temperature of 480 °C. The hardness change is attributed to the precipitation of metastable phases associated with the α-Al₁₅(Fe, Mn)₃Si₂ phase containing a large amount of impurity elements (Fe and Mn). At a lower temperature of 400 °C, a slight artificial-age hardening appeared. Subsequently, the hardness decreased moderately. This phenomenon was attributed to the precipitation of stable θ-Al₂Cu and Q-Al₄Cu₂Mg₈Si₆ phases and their coarsening after a long duration. The precipitation sequence was rationalized by thermodynamic calculations for the Al–Si–Cu–Fe–Mn–Mg system. The natural age-hardening behavior significantly varied depending on the prior artificial aging temperatures ranging from 400 °C to 500 °C. The natural age-hardening was found to strongly depend on the solute contents of Cu and Si in the Al matrix. This study provides fundamental insights into controlling the strength level of commercial Al–Si–Cu cast alloys with impurity elements using the cooling process after solution treatment at elevated temperatures above 400 °C.     

Functionally Graded Al2O3–CTZ Ceramics Fabricated by Spark Plasma Sintering

We studied the fabrication of functionally graded Al₂O₃–CeO₂-stabilized-ZrO₂ (CTZ) ceramics by spark plasma sintering. The ceramic composite exhibits a gradual change in terms of composition and porosity in the axial direction. The composition gradient was created by layering starting powders with different Al₂O₃ to CTZ ratios, whereas the porosity gradient was established with a large temperature difference, which was induced by an asymmetric graphite tool configuration during sintering. SEM investigations confirmed the development of a porosity gradient from the top toward the bottom side of the Al₂O₃–CTZ ceramic and the relative pore volume distributed in a wide range from 0.02 to 100 µm for the samples sintered in asymmetric configuration (ASY), while for the reference samples (STD), the size of pores was limited in the nanometer scale. The microhardness test exhibited a gradual change along the axis of the ASY samples, reaching 10 GPa difference between the two opposite sides of the Al₂O₃–CTZ ceramics without any sign of delamination or cracks between the layers. The flexural strength of the samples for both series showed an increasing tendency with higher sintering temperatures. However, the ASY samples achieved higher strength due to their lower total porosity and the newly formed elongated CeAl₁₁O₁₈ particles.     

Effect of Cr Content on Corrosion Resistance of Ni–xCr–Mo Laser-Cladding Coatings under H2S-Induced High-Temperature Corrosion Atmosphere

Ni–xCr–Mo laser-cladding coatings with varying Cr content of 10, 15, 20, 25, and 30 wt.% were fabricated using a self-assembled coaxial laser-cladding device. The H₂S-induced high-temperature corrosion tests under reductive atmosphere were conducted at 500, 550, and 600 °C. Subsequently, the influence of Cr content on the microstructural evolution and corrosion resistance of the Ni–xCr–Mo coatings was investigated. The experimental results revealed that 30 wt.% Cr is the limited maximum content that forms the suitable morphology of coatings without large prominent pores and cracks during the fabrication process, and 15 wt.% Cr corresponds to the critical minimum content for excellent corrosion resistance, as implied from the variation tendency of the corrosion weight-gain curves. Moreover, a two-layer structure of the corrosion scales was observed in the Ni–xCr–Mo laser-cladding coatings, which was primarily caused by the selective corrosion between the Ni and S and Cr/Mo and O.     

In Situ Observation of the Tensile Deformation and Fracture Behavior of Ti–5Al–5Mo–5V–1Cr–1Fe Alloy with Different Microstructures

The plastic deformation processes and fracture behavior of a Ti–5Al–5Mo–5V–1Cr–1Fe alloy with bimodal and lamellar microstructures were studied by room-temperature tensile tests with in situ scanning electron microscopy (SEM) observations. The results indicate that a bimodal microstructure has a lower strength but higher ductility than a lamellar microstructure. For the bimodal microstructure, parallel, deep slip bands (SBs) are first noticed in the primary α (α_p) phase lying at an angle of about 45° to the direction of the applied tension, while they are first observed in the coarse lath α (α_L) phase or its interface at grain boundaries (GBs) for the lamellar microstructure. The β matrix undergoes larger plastic deformation than the α_L phase in the bimodal microstructure before fracture. Microcracks are prone to nucleate at the α_p/β interface and interconnect, finally causing the fracture of the bimodal microstructure. The plastic deformation is mainly restricted to within the coarse α_L phase at GBs, which promotes the formation of microcracks and the intergranular fracture of the lamellar microstructure.     

The Effect of Heat Treatment on the Tribological Properties and Room Temperature Corrosion Behavior of Fe–Cr–Al-Based OPH Alloy

The microstructure, mechanical, tribological, and corrosion properties of Fe–Cr–Al–Y-based oxide-precipitation-hardened (OPH) alloy at room temperature are presented. Two OPH alloys with a composition of 0.72Fe–0.15Cr–0.06Al–0.03Mo–0.01Ta–0.02Y₂O₃ and 0.03Y₂O₃ (wt.%) were prepared by mechanical alloying with different milling times. After consolidation by hot rolling, the alloys presented a very fine microstructure with a grain size of approximately 180 nm. Such a structure is relatively brittle, and its mechanical properties are enhanced by heat treatment. Annealing was performed at three temperatures (1000 °C, 1100 °C, and 1200 °C), with a holding time from 1 to 20 h. Tensile testing, wear testing, and corrosion testing were performed to evaluate the effect of heat treatment on the behavior and microstructural properties. The grain size increased almost 10 times by heat treatment, which influenced the mechanical properties. The ultimate tensile strength increased up to 300% more compared to the initial state. On the other hand, heat treatment has a negative effect on corrosion and wear resistance.     

Drop–Dry Deposition of Ni(OH)2 Precursors for Fabrication of NiO Thin Films

Drop–dry deposition (DDD) is a method of depositing thin films by heating and drying the deposition solution dropped on a substrate. We prepared Ni(OH)₂ precursor thin films by DDD and annealed them in air to prepare NiO thin films. The appropriate deposition conditions were found by changing the number of drop–dry cycles and the concentrations of chemicals in the solution, and the Ni(OH)₂ precursor film with a thickness of 0.3 μm and optical transmittance of more than 95% was successfully deposited. Raman and X-ray diffraction measurements were performed, and it was found that the NiO film was successfully fabricated after annealing at 400 °C. The p-type conductivity of the annealed film was confirmed by photoelectrochemical measurements. In addition, we prepared n-type ZnO by electrochemical deposition on NiO thin films. The current–voltage measurement results show that the ZnO/NiO heterojunction had rectification properties.     

Effect of Al2Ca Addition and Heat Treatment on the Microstructure Modification and Tensile Properties of Hypo-Eutectic Al–Mg–Si Alloys

The current study investigated the microstructure modification in Al–6Mg–5Si–0.15Ti alloy (in mass %) through the minor addition of Ca using Mg + Al₂Ca master alloy and heat treatment to see their impact on mechanical properties. The microstructure of unmodified alloy (without Ca) consisted of primary Al, primary Mg₂Si, binary eutectic Al–Mg₂Si, ternary eutectic Al–Mg₂Si–Si, and iron-bearing phases. The addition of 0.05 wt% Ca resulted in significant microstructure refinement. In addition to refinement, lamellar to fibrous-type modification of binary eutectic Al–Mg₂Si phases was also achieved in Ca-added (modified) alloy. This modification was related to increasing Ca-based intermetallics/compounds in the modified alloy that acted as nucleation sites for binary eutectic Al–Mg₂Si phases. The dendritic refinement with Ca addition was related to the fact that it improves the efficacy of Ti-based particles (TiAl₃ and TiB₂) in the melt to act as nucleation sites. In contrast, the occupation of oxide bifilms by Ca-based phases is expected to force the iron-bearing phases (as iron-bearing phases nucleate at oxide films) to solidify at lower temperatures, thus reducing their size. The as-cast microstructure of these alloys was further modified by subjecting them to solution treatment at 540 °C for 6 h, which broke the eutectic structure and redistributed Mg₂Si and Si phases in Al-matrix. Subsequent aging treatment caused a dramatic increase in the tensile strength of these alloys, and tensile strength of 291 MPa (with El% of 0.45%) and 327 MPa (with El% of 0.76%) was achieved for the unmodified alloy and modified alloy, respectively. Higher tensile strength and elongation of the modified alloy than unmodified alloy was attributed to refined dendritic structure and modified second phases.     

Performance Comparison of Lattice-Matched AlInN/GaN/AlGaN/GaN Double-Channel Metal–Oxide–Semiconductor High-Electron Mobility Transistors with Planar Channel and Multiple-Mesa-Fin-Channel Array

In this work, Al_0.83In_0.17N/GaN/Al_0.18Ga_0.82N/GaN epitaxial layers used for the fabrication of double-channel metal–oxide–semiconductor high-electron mobility transistors (MOSHEMTs) were grown on silicon substrates using a metalorganic chemical vapor deposition system (MOCVD). A sheet electron density of 1.11 × 10¹³ cm⁻² and an electron mobility of 1770 cm²/V-s were obtained. Using a vapor cooling condensation system to deposit high insulating 30-nm-thick Ga₂O₃ film as a gate oxide layer, double-hump transconductance behaviors with associated double-hump maximum extrinsic transconductances (g_mmax) of 89.8 and 100.1 mS/mm were obtained in the double-channel planar MOSHEMTs. However, the double-channel devices with multiple-mesa-fin-channel array with a g_mmax of 148.9 mS/mm exhibited single-hump transconductance behaviors owing to the better gate control capability. Moreover, the extrinsic unit gain cutoff frequency and maximum oscillation frequency of the devices with planar channel and multiple-mesa-fin-channel array were 5.7 GHz and 10.5 GHz, and 6.5 GHz and 12.6 GHz, respectively. Hooge’s coefficients of 7.50 × 10⁻⁵ and 6.25 × 10⁻⁶ were obtained for the devices with planar channel and multiple-mesa-fin-channel array operating at a frequency of 10 Hz, drain–source voltage of 1 V, and gate–source voltage of 5 V, respectively.     

The Formation of 14H-LPSO in Mg–9Gd–2Y–2Zn–0.5Zr Alloy during Heat Treatment

There is a new long-period stacking ordered structure in Mg–RE–Zn magnesium alloys, namely the LPSO phase, which can effectively improve the yield strength, elongation, and corrosion resistance of Mg alloys. According to different types of Mg–RE–Zn alloy systems, two transformation modes are involved in the heat treatment transformation process. The first is the alloy without LPSO phase in the as-cast alloy, and the Mg_xRE phase changes to 14H-LPSO phase. The second is the alloy containing LPSO phase in the as-cast state, and the 14H-LPSO phase is obtained by the transformations of 6H, 18R, and 24R. The effects of different solution parameters on the second phase of Mg–9Gd–2Y–2Zn–0.5Zr alloy were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The precipitation mechanism of 14H-LPSO phase during solution treatment was further clarified. At a solution time of 13 h, the grain size increased rapidly initially and then decreased slightly with increasing solution temperature. The analysis of the volume fraction of the second phase and lattice constant showed that Gd and Y elements in the alloy precipitated from the matrix and formed 14H-LPSO phase after solution treatment at 490 °C for 13 h. At this time, the hardness of the alloy reached the maximum of 74.6 HV. After solution treatment at 500 °C for 13 h, the solid solution degree of the alloy increases, and the grain size and hardness of the alloy remain basically unchanged.