Microstructure and mechanical properties of plasma sprayed HA/YSZ/Ti-6Al-4V composite coatings

Plasma sprayed hydroxyapatite (HA) coatings on titanium alloy substrate have been used extensively due to their excellent biocompatibility and osteoconductivity. However, the erratic bond strength between HA and Ti alloy has raised concern over the long-term reliability of the implant. In this paper, HA/yttria stabilized zirconia (YSZ)/Ti-6Al-4V composite coatings that possess superior mechanical properties to conventional plasma sprayed HA coatings were developed. Ti-6Al-4V powders coated with fine YSZ and HA particles were prepared through a unique ceramic slurry mixing method. The so-formed composite powder was employed as feedstock for plasma spraying of the HA/YSZ/Ti-6Al-4V coatings. The influence of net plasma energy, plasma spray standoff distance, and post-spray heat treatment on microstructure, phase composition and mechanical properties were investigated. Results showed that coatings prepared with the optimum plasma sprayed condition showed a well-defined splat structure. HA/YSZ/Ti-6Al-4V solid solution was formed during plasma spraying which was beneficial for the improvement of mechanical properties. There was no evidence of Ti oxidation from the successful processing of YSZ and HA coated Ti-6Al-4V composite powders. Small amount of CaO apart from HA, ZrO(2) and Ti was present in the composite coatings. The microhardness, Young's modulus, fracture toughness, and bond strength increased significantly with the addition of YSZ. Post-spray heat treatment at 600 degrees C and 700 degrees C for up to 12h was found to further improve the mechanical properties of coatings. After the post-spray heat treatment, 17.6% increment in Young's modulus (E) and 16.3% increment in Vicker's hardness were achieved. The strengthening mechanisms of HA/YSZ/Ti-6Al-4V composite coatings were related to the dispersion strengthening by homogeneous distribution of YSZ particles in the matrix, the good mechanical properties of Ti-6Al-4V and the formation of solid solution among HA, Ti alloy and YSZ components.     

In vitro studies of plasma-sprayed hydroxyapatite/Ti-6Al-4V composite coatings in simulated body fluid (SBF)

The bioactivity of plasma-sprayed hydroxyapatite (HA)/Ti-6Al-4V composite coatings was studied by soaking the coatings in simulated body fluid (SBF) for up to 8 weeks. This investigation was aimed at elucidating the biological behaviour of plasma-sprayed HA/Ti-6Al-4V composite coatings by analyzing the changes in chemistry, and crystallinity of the composite coating in a body-analogous solution. Phase composition, microstructure and calcium ion concentration were analyzed before, and after immersion. The mechanical properties, such as tensile bond strength, microhardness and Young's modulus were appropriately measured. Results demonstrated that the tensile bond strength of the composite coating was significantly higher than that of pure HA coatings even after soaking in the SBF solution over an 8-weeks period. Dissolution of Ca-P phases in SBF was evident after 24h of soaking, and, a layer of carbonate-apatite covered the coating surface after 2 weeks of immersion. The mechanical properties were found to diminish with soaking duration. However, slight variation in mechanical properties was found after supersaturation of the calcium ions was attained with the precipitation of the calcium phosphate layers.     

In vitro behavior of sintered powder injection molded Ti-6Al-4V/HA

This article reports the morphology and mechanical properties of sintered powder injection molded Ti-6Al-4V/HA parts in a simulated physiological environment. Sintered Ti-6Al-4V/HA parts were immersed in a simulated body fluid (SBF) with ion concentrations that were comparable to those of human blood plasma for a total period of 12 weeks. At intervals of 2 weeks, the immersed Ti-6Al-4V/HA parts were analyzed with the use of scanning electron microscopy (SEM), X-ray diffractometry (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Mechanical properties such as flexural strength, flexural modulus, compressive strength, and compressive modulus were also evaluated. Results showed that complete dissolution of the more soluble phases such as tricalcium phosphate (TCP), tetracalcium phosphate (TTCP), and calcium oxide (CaO) were found after 2 weeks of immersion in SBF. ICP analysis showed that high calcium concentration release of around 200 ppm was observed in the SBF solution after 2-4 weeks of immersion, indicating that dissolution has taken place. Next, a gradual decrease in calcium concentration release in the SBF solution was observed after immersion for 4-6 weeks, with increasing amounts of calcium phosphate precipitates being observed on the Ti-6Al-4V/HA surface. Mechanical properties such as strength and modulus were found to deteriorate during 2-4 weeks of immersion, followed by gradual increment as the immersion period increased. This study also showed that parts sintered at 1150 C exhibited faster dissolution and precipitation rates than parts sintered at 1050 C in a physiological environment.     

TEM and STEM analysis on heat-treated and in vitro plasma-sprayed hydroxyapatite/Ti-6Al-4V composite coatings

A cogent understanding of the microstructure, and indeed nano-structure, of hydroxyapatite (HA) and the interface between Ti-6Al-4V and HA is crucial to its appropriateness as a biomaterials. This paper reports the analysis of plasma-sprayed HA/Ti-6Al-4V composites by transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) to elucidate the intricate nature of the materials following plasma spray processing and in vitro evaluation. The novel Ti-6Al-4V/HA composite coating, with approximately 48 wt% HA, had demonstrated attractive tensile adhesion strength (approximately 28 MPa) and improved Young's modulus (approximately 55 GPa). Experimental results demonstrated that amorphous calcium phosphate and fine HA grains were formed during rapid splat solidification in the as-sprayed composite coatings. Small Ti-6Al-4V grains were observed adjacent to the amorphous calcium phosphate. The coatings were further heat treated at 600 degrees C for 6 h, and significant crystallisation of the amorphous calcium phosphate phase took place. However, complete crystallisation was not achieved at this temperature, as the coatings invariably contained a small amount of amorphous calcium phosphate phase in some local regions. After immersion in simulated body fluid for 2 weeks and 10 weeks, TEM and STEM confirmed that the interfaces inside the coating maintained good microstructural integrity.     

Activity of plasma sprayed yttria stabilized zirconia reinforced hydroxyapatite/Ti-6Al-4V composite coatings in simulated body fluid

Hydroxyapatite (HA)/yttria stabilized zirconia/Ti-6Al-4V bio-composite coatings deposited onto Ti-6Al-4V substrate through a plasma spray technique were immersed in simulated body fluid (SBF) to investigate their behavior in vitro. Surface morphologies and structural changes in the coatings were analyzed by scanning electron microscopy, thin-film X-ray diffractometer, and X-ray photoelectron spectroscopy. The tensile bond strength of the coatings after immersion was also conducted through the ASTM C-633 standard for thermal sprayed coatings. Results showed that carbonate-containing hydroxyapatite (CHA) layer formed on the surface of composite coatings after 4 weeks immersion in SBF solution, indicating the composite coating possessed excellent bioactivity. The mechanical properties were found to decrease with immersion duration of maximum 56 days. However, minimal variation in mechanical properties was found subsequent to achieving supersaturation of the calcium ions, which was attained with the precipitation of the calcium phosphate layers. The mechanical properties of the composite coating were found to be significantly higher than those of pure HA coatings even after immersion in the SBF solution, indicating the enhanced mechanical properties of the composite coatings.     

Structure and immersion behavior of plasma-sprayed apatite-matrix coatings

The microstructure and properties of a series of plasma-sprayed coatings from sinter-granulated powders fabricated from SiO2, CaO, P2O5 and Na2O-containing HA composite powders on Ti-6Al-4V substrate were reported. The immersion behavior of these coatings in a simulated body fluid (SBF) was also investigated. The results showed that sinter-granulated apatite-matrix powders were irregularly shaped and appeared quite similar. XRD patterns showed that during fabrication of the powders, P2O5 and SiO2 enhanced the decomposition of HA structure, while CaO and Na2O did not. Reasonably high bond strengths (45-50 MPa) were obtained from all coatings. The plasma spray process itself enhanced the decomposition of apatite and chemical reactions among different phases. When immersed in SBF, the intensities of such phases as alpha- and beta-TCP in all coatings decreased with immersion time and an apatite precipitation took place on all coating surfaces. The immersed SiO2- and CaO-containing HA (HSC) coating had the highest rate of apatite precipitation among all coatings. The variations in calcium ion concentration in simulated body fluid indicated that the HSC-immersed solution reached its maximal Ca concentration the earliest, while the HSCP (HA, SiO2, CaO and P2O5)-immersed solution reached its maximum the latest.     

Microstructures and mechanical properties of powder injection molded Ti-6Al-4V/HA powder

Taguchi method with an L9 orthogonal array was employed to investigate the sintered properties of Ti-6Al-4V/HA tensile bars produced by powder injection molding. The effects of sintering factors at the 90% significance level: sintering temperature (1050 degrees C, 1100 degrees C and 1150 degrees C), heating rate (5 degrees C/min, 7.5 degrees C/min and 10 degrees C/min), holding time (30, 45 and 60 min) and cooling rate (5 degrees C/min, 20 degrees C/min and 40 degrees C/min) were investigated. Results showed that sintering temperature, heating rate and cooling rate have significant effects on sintered properties, whereas the influence of holding time was insignificant. It was found that a sintering temperature of 1100 degrees C, a heating rate of 7.5 degrees C/min and a cooling rate of 5 degrees C/min increased the relative density, Vicker's microhardness, flexural strength and flexural modulus. However, a further increment of sintering temperature to 1150 degrees C did not show any discernable improvement in the relative density and Vicker's microhardness, but there was a slight increase of 0.6% and 0.9% in the flexural strength and flexural modulus, respectively. Mechanically strong Ti-6Al-4V/HA parts with an open porosity of around 50% were developed.     

In vitro and in vivo studies of alkali- and heat-treated Ti-6Al-7Nb and Ti-5Al-2Nb-1Ta alloys for orthopedic implants

In vitro studies of Ti-6Al-7Nb and Ti-5Al-2Nb-1Ta alloys were carried out by treating the specimens with 10 M NaOH at 60 degrees C for 24 h and subsequently heat-treated at 600 degrees C for 1 h. After the alkali and heat treatments, and on subsequent soaking in simulated body fluid (SBF), the morphological and compositional changes on the surface of the specimens were examined using scanning electron microscope attached with an energy-dispersive electron probe X-ray analyzer. The results revealed a dense and uniform bonelike apatite layer on the surface of treated substrates immersed in SBF solution. In vivo studies were carried out in rats to evaluate osteoconduction of Ti-6Al-7Nb and Ti-5Al-2Nb-1Ta alloys surface after alkali and heat treatments compared with untreated titanium alloys as the control. The following titanium implants were prepared from these species: (1) control without implant; (2) untreated titanium implant; (3) alkali- and heat-treated implant--the implants were immersed in 10 M NaOH solution at 60 degrees C for 24 h and subsequently heated at 600 degrees C for 1 h. The specimens were inserted into the medial side of each tibia of rats. Histologically, direct bone contact with the implant surface was significantly higher in the alkali heat-treated implants than the untreated titanium implants.     

植入用Ti-6Al-4V合金模拟体液浸泡后高频和超高周疲劳性能

目的为预测植入用Ti-6Al-4V钛合金的使用寿命,研究其在模拟体液浸泡后,107周次以后的超高周疲劳性能。方法将Ti-6Al-4V钛合金试样在模拟体液中分别浸泡2 d和6 d;利用超声疲劳实验技术,在室温下分别对这两组试样进行超高周疲劳性能测试;利用电子显微镜观察疲劳断口并对裂纹源进行X射线能谱分析,研究其裂纹萌生机理,并与未经浸泡的同种材料的超声疲劳性能进行对比分析。结果模拟体液浸泡后的材料的S-N曲线与未经浸泡时的趋势相近,在104～108周次范围内的疲劳寿命都呈连续下降状态,在107～108周次循环范围内曲线下降趋势有所变慢;模拟体液浸泡后的试样在107周次之前寿命下降更快,107周次之后模拟体液浸泡过的试样寿命比未处理的试样寿命低;浸泡6 d后的试样的寿命和浸泡2 d后的相差不大。疲劳循环超过107周次后,仍然发生疲劳断裂,并不存在传统意义上的疲劳极限。疲劳寿命108周次以后的试样疲劳裂纹在内部萌生,一般为铝元素聚集区;疲劳寿命107周次以前裂纹一般萌生于试件表面,有些试件出现了多处裂纹源。结论模拟体液浸泡会降低Ti-6Al-4V钛合金的超高周疲劳性能;随着循环周次的增加,裂纹萌生由试件表面向其内部转换。     

In vitro stability of plasma-sprayed hydroxyapatite coatings on Ti-6Al-4V implants under cyclic loading

The success of hydroxyapatite (HA)-coated Ti-6Al-4V implants relies on the long-term stability of HA coatings. In this study, the mechanical stability of plasma-sprayed HA coatings on Ti-6Al-4V implants under four-point cyclic bending was systematically investigated in both air and simulated body fluid (SBF) environments at room temperature. To have a clear view of the microscale damage evolution, the surface morphology change of HA coatings during cyclic loading was carefully examined by scanning electron microscopy at the same locations on the coating surfaces after four-point bending for 4, 6.5, 8.5, and 10 million cycles. Also, possible changes of other characteristics such as thickness, weight, crystallinity, and residual stress of HA coatings were measured as a function of loading cycles. Up to 10 million cycles of bending in air and SBF, we found no significant microcracking or coating spalling on the surface of coatings, and no significant changes in thickness, weight, crystallinity, or residual stress of the plasma-sprayed HA coatings. The experiment results indicate that thickness and crystallinity had no effects on the stability of the HA coatings. HA coating resistance to the cyclic four-point bending might result from the stress shielding effects of preexisting microcracks in the coatings.     

Bond strength determination of hydroxyapatite coatings on Ti-6Al-4V substrates using the LAser Shock Adhesion Test (LASAT)

An adhesion test procedure applied to plasma-sprayed hydroxyapatite (HA) coatings to measure the "LASAT threshold" (LAser Shock Adhesion test) is described. The good repeatability and minimal discrepancy of the laser-driven adhesion test data were ascertained for conventional plasma sprayed HA coatings. As a further demonstration, the procedure was applied to HA coatings with diverse characteristics on the ceramic/metal interface. Different preheating and grit blasting conditions and the presence of a thick plasma-sprayed Ti sublayer or a thin TiO(2) layer prepared by oxidation were investigated through LASAT. It was assessed that a rough surface can significantly improve the coating's bond strength. However, it was also demonstrated that a thin TiO(2) layer on a smooth Ti-6Al-4V substrate can have a major influence on adhesion as well. Preheating up to 270°C just prior to the first HA spraying pass had no effect on the adhesion strength. Further development of the procedure was done to achieve an in situ LASAT with in vitro conditions applied on HA coatings. To that end, different crystalline HA contents were soaked in simulated body fluid (SBF). Beyond the demonstration of the capability of this laser-driven adhesion test devoted to HA coatings in dry or liquid environment, the present study provided empirical information on pertinent processing characteristics that could strengthen or weaken the HA/Ti-6Al-4V bond.     

Bond strength of plasma-sprayed hydroxyapatite/Ti composite coatings

One of the most important clinical applications of hydroxyapatite (HA) is as a coating on metal implants, especially plasma-sprayed HA coating applied on Ti alloy substrate. However, the poor bonding strength between HA and Ti alloy has been of concern to orthopedists. In this paper, an attempt has been made to enhance the bonding strength of HA coating by forming a composite coating with Ti. The bioactivity of the coating has also been studied. HA/Ti composite coatings were prepared via atmospheric plasma spraying on Ti-6Al-4V alloy substrates. The bond strength evaluation of HA/Ti composite coatings was performed according to ASTM C-633 test method. X-ray diffractometer and scanning electron microscopy were applied to identify the phases and the morphologies of the coatings. The bioactivity of HA/Ti composite coating was qualified by immersion of coating in simulated body fluid (SBF). The obtained results revealed that the addition of Ti to HA improved the bonding strength of coating significantly. In the SBF test, the coating surface was covered by carbonate-apatite, which was testified by X-ray photoelectron spectroscope, indicating good bioactivity for HA/Ti composite coating. The bioactivity of the coating has not been reduced by the addition of Ti.     

Early bone apposition in vivo on plasma-sprayed and electrochemically deposited hydroxyapatite coatings on titanium alloy

Three different implants, bare Ti-6Al-4V alloy, Ti-6Al-4V alloy coated with plasma-sprayed hydroxyapatite (PSHA), and Ti-6Al-4V alloy coated with electrochemically deposited hydroxyapatite (EDHA), were implanted into canine trabecular bone for 6 h, 7, and 14 days, respectively. Environmental scanning electron microscopy study showed that PSHA coatings had higher bone apposition ratios than those exhibited by bare Ti-6Al-4V and EDHA coatings after 7 days; however, at 14 days after implantation, EDHA and PSHA coatings exhibited similar bone apposition ratios, much higher than that for bare Ti-6Al-4V. The ultrastructure of the bone/implant interface observed by transmission electron microscope showed that the earliest mineralization (6 h-7 days) was in the form of nano-ribbon cluster mineral deposits with a Ca/P atomic ratio lower than that of hydroxyapatite. Later-stage mineralization (7-14 days) resulted in bone-like tissue with the characteristic templating of self-assembled collagen fibrils by HA platelets. Though adhesion of EDHA coatings to Ti-6Al-4V substrate proved problematical and clearly needs to be addressed through appropriate manipulation of electrodepositon parameters, the finely textured microstructure of EDHA coatings appears to provide significant advantage for the integration of mineralized bone tissue into the coatings.     

Microstructure and corrosion behavior of porous coatings on titanium alloy by vacuum-brazed method

The microstructural evolution and electrochemical characteristics of brazed porous-coated Ti-6Al-4V alloy were analyzed and compared with respect to the conventionally 1300 degrees C sintering method. The titanium filler metal of low-melting-point (934 degrees C) Ti-15Cu-15Ni was used to braze commercially pure (CP) titanium beads onto the substrate of Ti-6Al-4V alloy at 970 degrees C for 2 and 8 h. Optical microscopy, scanning and transmission electron microscopy, and X-ray diffractometry (XRD) were used to characterize the microstructure and phase of the brazed metal; also, the potentiostat was used for corrosion study. Experimental results indicate that the bead/substrate contact interface of the 970 degrees C brazed specimens show larger contact area and higher radius curvature in comparison with 1300 degrees C sintering method. The microstructure of brazed specimens shows the Widmanst?tten structure in the brazed zone and equiaxed alpha plus intergranular beta in the Ti-6Al-4V substrate. The intermetallic Ti2Ni phase existing in the prior filler metal diminishes, while the Ti2Cu phase can be identified for the substrate at 970 for 2 h, but the latter phase decrease with time. In Hank's solution at 37 degrees C, the corrosion rates of the 1300 degrees C sintering and the 970 degrees C brazed samples are similar at corrosion potential (E(corr)) in potentiodynamic test, and the value of E(corr) for the brazed sample is noble to the sintering samples. The current densities of the brazed specimens do not exceed 100 microA/cm2 at 3.5 V (SCE). These results suggest that the vacuum-brazed method exhibits the potentiality to manufacture the porous-coated specimens for biomedical application.     

Synthesis of biomimetic Ca-hydroxyapatite powders at 37 degrees C in synthetic body fluids

An important inorganic phase for synthetic bone applications, calcium hydroxyapatite (HA, Ca10(PO4)6(OH)2), was prepared as a nano-sized (approximately 50 nm), homogeneous and high-purity ceramic powder from calcium nitrate tetrahydrate and diammonium hydrogen phosphate salts dissolved in modified synthetic body fluid (SBF) solutions at 37 degrees C and pH of 7.4 using a novel chemical precipitation technique. The synthesized precursors were found to easily reach a phase purity >99% after 6 h of calcination in air atmosphere at 90 degrees C, following oven drying at 80 degrees C. There was observed, surprisingly, no decomposition of HA into the undesired beta-TCP phase even after heating at 1,600 degrees C in air for 6 h. This observation showed the superior high-temperature stability of such 'biomimetic' HA powders as compared to those reported in previous studies. The former powders were also found to contain trace amounts of Na and Mg ions, originating from the use of SBF solutions instead of pure water during their synthesis. Characterization and chemical analysis of the synthesized powders were performed by X-ray powder diffraction, energy-dispersive X-ray spectroscopy, Fourier-transform infra-red spectroscopy, scanning electron microscopy, and inductively coupled plasma atomic emission spectroscopy.     

Bioactive calcium phosphate invert glass-ceramic coating on beta-type Ti-29Nb-13Ta-4.6Zr alloy

A fine, strong coating consisting of a bioactive calcium phosphate invert glass-ceramic can be prepared easily by reaction of the glassy phase with an oxide layer formed on a new beta-type titanium alloy, Ti-29Nb-13Ta-4.6Zr, when the metal, on which the mother glass powders with a composition of 60CaO-30P(2)O(5)-7Na(2)O-3TiO(2) in mol% are placed, is heated at 800 degrees C in air. A compositionally gradient layer is developed on the titanium alloy during the heating. Tensile bonding strength of the coating to the metal is significantly higher than those of the coatings to conventional metals such as Ti-6Al-4V alloy or pure titanium. The oxidized layer on Ti-29Nb-13Ta-4.6Zr alloy is relatively thinner than that on Ti-6Al-4V alloy even with heat treatment in air; large tensile stresses are not generated in the layer.     

Immersion behavior of RF magnetron-assisted sputtered hydroxyapatite/titanium coatings in simulated body fluid.

The focus of the present study was on the dissolution/degradation behavior of a series of magnetron-sputtered, single-layered HA/Ti coatings on Ti-6Al-4V substrate immersed in SBF. Changes in coating morphology, crystal structure, and adhesion strength with immersion time are characterized. XRD, FTIR, and LVSEM results consistently indicate that highly crystalline monolithic HA coating is very dissolvable in SBF. The monolithic HA coating is largely delaminated in 3 weeks and entirely peeled off the substrate in 7 weeks. The dissolution is even greater for 95HA/5Ti coating, which severely disintegrated in only 1 week. The amorphous-like coatings sputtered from targets comprising 10 vol % or more Ti, however, appeared almost intact, and their adhesion strengths, which were all higher than 60 MPa, did not change much (within 10%) even after 14 weeks of immersion. The coatings from targets comprising roughly 10-50 vol % Ti combine advantages of high and nondeclining adhesion strength, high resistance to SBF attack, and possibly much higher bioactivity (with large amounts of Ca, P, etc., dissolved in the coatings) than that of Ti.     

Effect of thermal oxidation on corrosion and corrosion-wear behaviour of a Ti-6Al-4V alloy

In this study, comparative investigation of thermal oxidation treatment for Ti-6Al-4V was carried out to determine the optimum oxidation conditions for further evaluation of corrosion-wear performance. Characterization of modified surface layers was made by means of microscopic examinations, hardness measurements and X-ray diffraction analysis. Optimum oxidation condition was determined according to the results of accelerated corrosion tests made in 5m HCl solution The examined Ti-6Al-4V alloy exhibited excellent resistance to corrosion after oxidation at 600 degrees C for 60 h. This oxidation condition achieved 25 times higher wear resistance than the untreated alloy during reciprocating wear test conducted in a 0.9% NaCl solution.     

Elastic and plastic behavior of plasma-sprayed hydroxyapatite coatings on a Ti-6Al-4V substrate

A novel approach that combines the indentation tests with nonlinear finite element modeling (FEM) is proposed to estimate the elastic/plastic constitutive relation of plasma-sprayed hydroxyapatite (HA) coatings on a Ti-6Al-4V substrate. The Ramberg-Osgood constitutive equation can well describe the deformation behavior of plasma-sprayed HA coating on Ti-6Al-4V. A reasonable estimation for the elastic modulus of the HA coatings is given, based on the fact that the coating consists of a crystalline phase, an amorphous phase and pores. The Ramberg-Osgood equations of the coatings indicate that the post-treatment increases both resistance to elastic and plastic deformation, but no effect on strain hardening behavior. The post-treatment, however, could reduce the resistance to coating/substrate separation. The influence of titanium substrate becomes more significant with decreasing coating thickness and increasing indentation load because the plasma-sprayed HA coatings exhibit much less resistance to indentation deformation than does Ti-6Al-4V.     

Bone formation at the surface of low modulus Ti-7.5Mo implants in rabbit femur

The biocompatibility of the Ti-7.5Mo alloy was examined, because the alloy has a high-strength/modulus ratio and thus is a potential candidate for orthopedic applications. Cell viability assay using 3T3 cells revealed that the Ti-7.5Mo did not induce apparent cell death, when the cells were grown on disks made of the alloy or incubated with the alloy-conditioned medium at 37 or 72 degrees C for 24-72h. The Ti-6Al-4V alloy was used as a control and did not cause apparent cell death either. Moreover, pins of 6mm long and 2mm in diameter of Ti-7.5Mo and Ti-6Al-4V were implanted into the left and right rabbit femurs, respectively, for 6, 12 and 26 weeks. New bone tissue grew to surround the pins, which spanned cortical and marrow regions, as shown by toluidine blue-stained bone sections of the three time points. Strikingly, the amount of new bone encircling the Ti-7.5Mo implant was approximate two-folds of that at Ti-6Al-4V by 26 weeks post-implantation. This facilitation of bone formation could be associated with the unique properties, such as a low modulus and the composition of Mo, of the Ti-7.5Mo.