Poly(3‐hexylthiophene)‐block‐poly(2‐ethyl‐2‐oxazoline) amphiphilic rod–coil diblock copolymers have been synthesized by a combination of Grignard metathesis (GRIM) and ring‐opening cationic polymerization. Diblock copolymers containing 5, 15, and 30 mol‐% poly(2‐ethyl‐2‐oxazoline) have been synthesized and characterized. The synthesized rod–coil block copolymers display nanofibrillar morphology where the density of the nanofibrills is dependent on the concentration of the poly(2‐ethyl‐2‐oxazoline) coil segment. The conductivity of the diblock copolymers was lowered from 200 to 35 S · cm?1 with an increase in the content of the insulating poly(2‐ethyl‐2‐oxazoline) block. By contrast, the field‐effect mobility decreased by 2–3 orders of magnitude upon the incorporation of the poly(2‐ethyl‐2‐oxazoline) insulating segment.
Two new donor/acceptor copolymers PBDTPhBT1 and PBDTPhBT2 with alternating benzodithiophene ( BDT ) and bisthiophene‐phthalimide ( PhBT ) units were synthesized by Stille coupling reaction. The copolymers showed identical optical bandgaps of 1.98 eV. The HOMO energy levels are ?5.35 and ?5.32 eV for PBDTPhBT1 and PBDTPhBT2 , respectively. The bulk heterojunction solar cell devices based on these copolymers as donors and PC71BM as acceptor displayed high open‐circuit voltages of 0.90–0.93 V and achieved power conversion efficiency of 1.54% under the illumination of AM 1.5, 100 mW · cm?2.
Biodegradable and photocurable block copolymers of ε‐caprolactone and L ‐lactide were synthesized by polycondensation of PLLA diol ( = 10 000 g · mol?1), PCL diol ( = 10 000 g · mol?1), and a chain extender bearing a coumarin group. The effect of copolymer composition on the thermal and mechanical properties of the photocured copolymers was studied by means of DSC and cyclic tensile tests. An increase in Young's modulus and a decrease in the tensile strain with increasing PLLA content was observed for the block copolymers. Block copolymers with high PCL content showed good to excellent shape‐memory properties. Random copolymers exhibited Rf and Rr values above 90% at 45 °C for an extremely large tensile strain of 1 000%.
Cyclopentyl‐ and cyclohexyl‐substituted polysiloxanes terminated with amino groups were prepared. Initially, the cycloalkene and dichlorosilane were reacted at high pressure (approx. 250 psi) and high temperature (120 °C) to yield the cycloaliphatic dichlorosilane in a two‐step process. Both the mono‐ and disubstituted chlorosilane monomers underwent an oligomerization to produce cyclic oligomers of low molecular weight (≈2 000 g · mol?1). Amine‐terminated polysiloxanes were produced via a base‐catalyzed ring‐opening polymerization of the cyclic oligomers with 1,3‐bis(3‐aminopropyl)tetramethyldisiloxane to yield low molecular weight polysiloxanes (≈9 000 g · mol?1, amine equivalent weight = ≈4 300 g · equiv.?1). The polysiloxanes were characterized by 1H and 29Si NMR, and Fourier transform‐infrared spectroscopy (FT‐IR). The amine‐terminated polysiloxane was mixed with a cycloaliphatic epoxy‐functionalized cycloaliphatic polysiloxane in order to produce crosslinked epoxy–amine films. The mechanical and physical properties of the film were evaluated and afford a glass transition of the material was 29.5 ± 0.7 °C for the cyclopentyl‐substituted polysiloxane and 38.6 ± 0.7 °C for the cyclohexyl‐substituted polysiloxane. Evaluation of pull‐off adhesion indicated that 0.5 MPa of normal force was required to remove the epoxy/amine film from an aluminum substrate.
Two narrow bandgap copolymers derived from 6,6′,12,12′‐tetraoctyl‐indeno[1,2‐b]fluorene and bithiophene or thieno[3,2‐b]thiophene‐cored benzothiadiazole are synthesized and characterized. The copolymers show broad absorption in the range 350–700 nm. The application of the copolymers as photovoltaic cells with configurations ITO/PEDOT:PSS/blend/Al and ITO/PEDOT:PSS/blend/interlayer/Al is investigated. A power conversion efficiency (PCE) of approximately 3.0% is achieved under an AM 1.5G solar simulator (80 mW cm?2) for the cells with ITO/PEDOT:PSS/polymer:PC71BM([6,6]‐phenyl‐C71 butyric acid methyl ester) (1:4)/interlayer/Al.
Summary: Two types of bis(2,5‐diphenyl‐1,3,4‐oxadiazole)s, macrocyclic and acyclic, were prepared and evaluated as electron‐transporting and hole‐blocking materials in phosphorescent EL devices. Maximum efficiencies of ηext = 10.4% at J = 0.11 mA · cm−2 for the macrocycle and ηext = 14.1% at J = 3.01 mA · cm−2 for the acycle were observed. X‐ray crystallographic analysis and DSC measurements revealed a strong intermolecular interaction between the macrocycles and weaker intermolecular interactions between the acycles. The EL characteristics depend on the intermolecular interactions.
The two types of bis(2,5‐diphenyl‐1,3,4‐oxadiazole)s used in the study. 相似文献
pH‐sensitive micelles formed by interchain hydrogen bonding of poly(methacrylic acid)‐block‐poly(ethylene oxide) copolymers were prepared and investigated at pH < 5. Both and Rh of the micelles increase with decreasing pH of the solution, displaying an asymptotic tendency at low pH values. The observed micelles are well‐defined nanoparticles with narrow size distributions (polydispersity ΔRh/Rh ≤ 0.05) comparable with regular diblock copolymer micelles. The CMCs occur slightly below c = 1 × 10?4 g · mL?1. The micelles are negatively charged and their time stability is lower than that of regular copolymer micelles based purely on hydrophobic interactions.
New polyurethanes containing Y‐shaped chromophores, symmetrical derivatives of 4‐(dicyanomethylene)‐2‐methyl‐6‐[p‐(dimethylamino)styryl]‐4H‐pyran, have been prepared. The polymers show high glass transition temperatures (Tg) and a good thermal stability. SHG measurements on poled polymer films of the synthesized polymers have been carried out and a maximum d33 of 15 pm · V?1 has been found at 1 368 nm fundamental wavelength. Time stability measurements on the most active polymer have shown that after the initial fast relaxation, the d33 value remains constant at 80 °C for 60 d.
The high‐pressure melt‐crystallization behaviors of poly(p‐phenylene sulfide) (PPS) were investigated using WAXD, DSC, TEM and SEM. PPS extended‐chain crystals with c‐axis thickness exceeding 4.5 µm were formed at high pressure. The DSC results showed that the melting temperature and melting enthalpy of high‐pressure crystallized PPS samples were up to 327.53 °C and 94.96 J · g?1, respectively, which were higher than the values of ideal PPS perfect crystals used by some researchers, and the melting enthalpy of the samples fluctuated regularly during the thickening growth of the PPS crystals. Other characteristic morphologies obtained at high pressure, i.e. spherulites and rod‐like crystals, were also presented with the SEM measurements.
Poly(3‐hexylthiophene)‐block‐poly(tetrahydrofuran) was synthesized by cationic ring‐opening polymerization of tetrahydrofuran (THF) using a poly(3‐hexylthiophene) macroinitiator. Poly(3‐hexylthiophene) macroinitiator used for the ring‐opening polymerization of THF was synthesized by reacting the hydroxypropyl end‐group with trifluoromethanesulfonic anhydride in the presence of 2,6‐di‐tert‐butylpyridine. 1H NMR spectroscopy and SEC data confirmed the formation of the di‐block copolymers. Field‐effect mobility of poly(3‐hexylthiophene)‐block‐poly(tetrahydrofuran) was measured in a thin‐film transistor configuration and was found to be 0.009 cm2 · V?1 · s?1.
A series of three recently synthesised tetradentate chelated α‐diimine nickel complexes of the type [NiBr2(Ar‐BIAN)] (where Ar = 2‐(1‐R‐1H‐1,2,3‐triazol‐4‐yl)phenyl; R = benzyl 1 , 1‐phenylethyl 2 , phenyl 3 ) are used as precatalysts for the polymerisation of norbornene. When activated with MAO, 1 – 3 are highly active catalysts for the production of high molecular weight polynorbornene (e.g., 1.39 × 107 g PNB mol Ni?1 · h?1). The catalytic activity and polymer molecular weight increase markedly with the initial concentration of norbornene, but both parameters decrease with the reaction time. The characterisation of the polynorbornenes by NMR, GPC/SEC, X‐ray diffraction, and DSC/TGA leads to the assignment of a structure typical of a polynorbornene originated by a coordination vinyl addition mechanism.
Poly(ethylene oxide) of various molecular weights (Mn = 3 000, 5 200, 10 000, 16 500 g · mol?1) has been modified with terpyridine end groups as building blocks for water‐soluble metallo‐supramolecular polymers. Metallo‐supramolecular A–A homopolymers have been prepared and characterized by complexing the terpyridine units of one selected poly(ethylene oxide) (Mn = 3 000 g · mol?1) with the following transition metal ions in their 2+ oxidation state: Fe, Ru, Co, Ni, Cu, Zn, and Cd. In addition, the stability of the supramolecular connection with respect to pH variations has been investigated.
Schematic representation of the product of poly(ethylene oxide) modification with terpyridine end groups and the metal complexation. 相似文献
This work describes the effect of sulfuric acid protonation on the properties of SPOD‐DPE membranes using FT‐IR and impedance spectroscopic analyses. The IR spectra showed the protonation of nitrogen atoms from oxadiazole rings, with a broad band complex in the region 3 000–2 100 cm?1 with two centered peaks at 2 590 and 2 440 cm?1. The S?O characteristic absorption bands in SPOD‐DPE and sulfuric acid were specially studied in the region of 1 800–900 cm?1. The band shifts are associated to the interaction between acid groups and oxadiazole ring nitrogen atoms. The IR spectra evidenced the presence of three absorption species (HSO, SO and free H2SO4) depending on the sulfuric acid concentration. For the protonated SPOD‐DPE membranes, a proton conductivity around 10 mS · cm?1 was reached at 50 °C.
Long‐chain heteroatom‐containing telechelic diols with 29–32 atoms in the backbone were synthesized by a one‐step, free‐radical telomerization of 10‐undecene‐1‐ol with commercially available α,ω‐dithiols. The oxygen and sulfur atoms caused a decrease in the melting point and enthalpy of the diols, compared to the corresponding purely aliphatic diols. The heteroatom‐containing α,ω‐diols HO? (CH2)11? S? (CH2)2? X? (CH2)2? S? (CH2)11? OH, where X = CH2, O, or O? (CH2)2? O, were reacted in the melt with 1,6‐diisocyanatohexane O?C?N? (CH2)6? N?C?O, producing a series of polyurethanes containing an increasing amount of heteroatoms. Characterization by differential scanning calorimetry, infra‐red spectroscopy, thermogravimetric analysis, and wide angle x‐ray scattering of the m,n‐polyurethane series showed that, like the telechelic diols they were synthesized from, the heteroatoms caused a decrease in the melting point and enthalpy. However, they did not affect either the decomposition temperature or the crystal structure/packing.
Typical decomposition behavior of all the heteroatom‐containing m,6‐polyurethane. 相似文献
A novel AB2‐type blocked isocyanate monomer was synthesized which was de‐blocked to provide a hyperbranched poly(aryl ether urethane). Copolymerization of this monomer with a functionally similar AB monomer yielded polymers with molecular weights in the range 8.0–310 kDa with a DB of 41–59% that underwent two‐stage decomposition above 200 °C. The inherent viscosities of the polymers in DMF ranged from 0.09 to 1.10 dL · g?1. End‐group modification of hyperbranched poly(aryl ether urethane)s was carried out with PEG monomethyl ether and 1‐decanol and affected the thermal properties and solubilities of the polymers. Tg of the polymers was reduced significantly from 201 to 71 °C upon incorporation of AB monomer in the copolymerization.
Poly(4,4‐bis[(3,5‐diethoxybenzoyloxy)methyl]‐1,6‐heptadiyne) is synthesized via cyclopolymerization using modified Grubbs‐ and Schrock‐type initiators. Doping with either I2 or NO+ BF4? yields a conductive polymer with conductivity up to 1.4 × 10?2 S cm?1. The undoped amorphous conjugated polymer is spun into monofilament and multifilament fibers by a wet‐spinning process. Fibers are collected on bobbins with a draw down ratio of 12 resulting in fiber diameters under 60 μm, characterized by scanning electron microscopy. X‐ray diffraction data confirms that the amorphous structure of the polymer is preserved; no additional orientation of the polymer chains occurs during fiber spinning.
1,2,4‐triazole‐functional PGMA polymers have been synthesized and their anhydrous proton‐conducting properties were investigated after doping with phosphoric acid and triflic acid. PGMA was prepared by solution polymerization and then modified with 1H‐1,2,4‐triazole (Tri) and 3‐amino‐1,2,4‐triazole (ATri). FT‐IR, 13C NMR and elemental analysis verify the high immobilization of the triazoles in the polymer chain. Phosphoric‐acid‐doped polymers showed lower Tg and higher proton conductivities. PGMA‐Tri 4 H3PO4 showed a maximum water‐free proton conductivity of approximately 10?2 S · cm?1 while that of PGMA‐ATri 2 H3PO4 was 10?3 S · cm?1. The structure and dynamics of the polymers were explored by 1H MAS and 13C CP‐MAS solid‐state NMR.
Ozonolysis of unsaturated polymers produced useful telechelic oligomers that can form building blocks for networks and block copolymers. The unsaturated polymers can be prepared by semicontinuous emulsion polymerization with dienes, and here it is shown that the addition of cyclodextrins enhanced the incorporation of these comonomers. Both α‐ and β‐cyclodextrin provide copolymers with higher fractions of butadiene (BD) incorporated into the chain but α‐cyclodextrin had the highest levels of incorporation. Oxidative work up after ozonolysis produced latexes of carboxylic acid oligomers of different molar masses. A clear effect of polymer size on toxicity was observed with the oligomers with < 2 700 g · mol.?1 proving to have similar cytotoxic effects to lactic acid. However, oligomers with above 2 700 g · mol.?1 were cytocompatible and gave similar results to a polylactide control material.
A copper‐catalyzed Ullmann C–N coupling reaction was used for the preparation of a new carbazole‐based HPU in good yield with a high molecular weight through a facile “AB2 + A2 + B2”‐type approach. The HPU exhibited good solubility, high thermal stability with a Tg of 196 °C, as well as a suitable HOMO level for good hole injection and transporting properties. A two‐layer OLED device, using HPU as hole‐transporting layer (HTL) and Alq3 as the light‐emitting layer, was fabricated to investigate the hole‐transporting properties of HPU. The luminance efficiency reached 1.14 cd · A?1 at the maximum current density of 1 240 mA · cm?2, while the maximum luminance efficiency was 1.65 cd · A?1, indicating the high morphological and thermal stability of HPU.
A modular synthesis of short chain length and medium chain length poly(3‐hydroxyalkanoate)s‐b‐poly(ethylene glycol) (PHAs‐b‐PEG) diblock copolymers is described. First, length‐controlled oligomers of hydrophobic poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBHV), poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBHHx), and poly(3‐hydroxyoctanoate‐co‐hydroxyhexanoate) (PHOHHx) containing a carboxylic acid end group were obtained by thermal treatment, with molar masses ranging from 3 800 to 15 000 g · mol?1. After quantitative functionalization with propargylamine, ligation with azide‐terminated poly(ethylene glycol) of 5 000 g · mol?1 was accomplished using the copper (I) catalyzed azide alkyne cycloaddition (CuAAC). Well‐defined diblock copolymers were obtained up to 93% yield, with molar masses ranging from 9 900 to 23 100 g · mol?1. All products were fully characterized using 1H NMR, COSY, SEC, TGA, and DSC.
