In vitro inactivation of endodontic pathogens with Nd:YAG and Er:YAG lasers

Both Nd:YAG and Er:YAG lasers have been suggested as root canal disinfection aids. The aim of this in vitro study is to compare both wavelengths in terms of irradiation dose required for microbial inactivation, to quantify these irradiation doses and to investigate the influence of certain (laser) parameters on the antimicrobial efficacy. Agar plates containing a uniform layer of Enterococcus faecalis, Candida albicans or Propionibacterium acnes were mounted perpendicularly underneath the laser handpieces (5?mm spot). The Er:YAG laser was operated in single-pulse mode. Pulse energies of 40–400?mJ and pulse lengths of 100, 300, 600, and 1,000?μs were tested. After incubation at 37°C for 48?h, growth on the plates was scored. The pulse energy yielding complete absence of growth over the entire spot area was taken as the total inhibition threshold (TIT). TITs were determined for every species and pulse length. The Nd:YAG laser was operated with pulse trains because single pulses were ineffective. Output power was 15?W and frequency was 100?Hz. Spots were irradiated for 5–120?s. After incubation, the diameters of the inhibition zones were measured. For the Er:YAG laser, TITs varied between 100 and 210?mJ, and differed significantly between species and pulse lengths. Using Nd:YAG irradiation, TITs were around 5,300?J/cm² for C. albicans and 7,100?J/cm² for P. acnes. No inhibition was observed for E. faecalis. Er:YAG irradiation was superior to Nd:YAG in inactivating microorganisms on agar surfaces.     

Comparison of dentin root canal permeability and morphology after irradiation with Nd:YAG, Er:YAG, and diode lasers

The aim of this study was to compare the effects of Nd:YAG, Er:YAG, and diode lasers on the morphology and permeability of root canal walls. The three laser wavelengths mentioned interact differently with dentin and therefore it is possible that the permeability changes caused will determine different indications during endodontic treatment. Twenty-eight human single-rooted teeth were instrumented up to ISO 40 and divided into four groups: group C, control (GC), non-laser irradiated; group N (GN), irradiated with Nd:YAG laser; group E (GE), with Er:YAG laser and group D (GD) with diode laser. After that, the roots were filled with a 2% methylene blue dye, divided into two halves and then photographed. The images were analyzed using Image J software and the percentage of dye penetration in the cervical, middle, and apical root thirds were calculated. Additional scanning electron microscopy (SEM) analyses were also performed. The analysis of variance (ANOVA) showed significant permeability differences between all groups in the middle and cervical thirds (p < 0.05). The Tukey test showed that in the cervical third, GN presented means of dye penetration statistically significantly lower than all of the other groups. In the middle third, GE and GD showed statistically higher dye penetration means than GC and GN. SEM analysis showed melted surfaces for GN, clean wall surfaces with open dentinal tubules for GE, and mostly obliterated dentinal tubules for GD. Er:YAG (2,094 nm) laser and diode laser (808 nm) root canal irradiation increase dentinal permeability and Nd:YAG (1,064 nm) laser decreases dentin permeability, within the studied parameters.     

Effect of Er:YAG and Nd:YAG lasers on the mineral content of root canal dentin

Lasers in Medical Science - The aim of this study was to assess the effect of two different laser systems on the mineral content of root canal dentin. Thirty-six single canal-extracted mandibular...     

Laser reduction of specific microorganisms in the periodontal pocket using Er:YAG and Nd:YAG lasers: a randomized controlled clinical study

The objective of this study was to evaluate the microbiological and clinical outcomes following nonsurgical treatment by either scaling and root planing, combination of Nd:YAG and Er:YAG lasers, or by Er:YAG laser treatment alone. The study involved 60 patients with generalized chronic periodontitis, randomly assigned into one of three treatment groups of 20 patients. The first group received scaling and root planing by hand instruments (SRP group), the second group received Er:YAG laser treatment alone (Er group), and the third group received combined treatment with Nd:YAG and Er:YAG lasers (NdErNd group). Microbiological samples, taken from the periodontal pockets at baseline and 6 months after treatments, were assessed with PET Plus tests. The combined NdErNd laser (93.0%), followed closely by Er:YAG laser (84.9%), treatment resulted in the highest reduction of all bacteria count after 6 months, whereas SRP (46.2%) failed to reduce Treponema denticola, Peptostreptococcus micros, and Capnocytophaga gingivalis. Full-mouth plaque and bleeding on probing scores dropped after 6 months and were the lowest in both laser groups. The combination of NdErNd resulted in higher probing pocket depth reduction and gain of clinical attachment level (1.99?±?0.23 mm) compared to SRP (0.86?±?0.13 mm) or Er:YAG laser alone (0.93?±?0.20 mm) in 4–6 mm-deep pockets. Within their limits, the present results provide support for the combination of Nd:YAG and Er:YAG lasers to additionally improve the microbiological and clinical outcomes of nonsurgical periodontal therapy in patients with moderate to severe chronic periodontitis.     

Nd:YAG laser-induced interstitial hyperthermia using a long frosted contact probe

The heating potential of a closed loop interstitial hyperthermia system employing 1,064 nm laser light in conjunction with a long frosted contact probe was investigated in hind limb muscle of anesthetized dogs. The laser system was an Nd:YAG surgical laser modified with a single channel thermometry unit, a computer, a printer, and a computer-controlled laser exposure shutter. The long frosted laser probe was implanted into the muscle, and 3.12-5.00 Watts of laser power was delivered interstitially. Temperature distribution was measured in three dimensions around the frosted probe. The temperature distributions generated by this technique were satisfactory for producing desired hyperthermia temperatures in an approximately 3.5 cm3 cylindrical tissue volume. A multiple laser delivery system is needed to induce interstitial hyperthermia in large tumors. A significant potential for the long frosted contact probe may be its use in combining interstitial hyperthermia and interstitial photodynamic therapy. Using this technique, both modalities may be delivered while employing the same treatment setup.     

The effect of Nd:YAG and Er,Cr:YSGG lasers on the microhardness of human dentin

The current investigation determined the microhardness of dentin tissue irradiated with erbium, chromium-doped yttrium scandium gallium garnet (Er,Cr:YSGG) and neodymium-doped yttrium–aluminum garnet (Nd:YAG) lasers. Thirty non-carious human molars were used in this study. Dentin disks were prepared by horizontal sectioning of one third of the occlusal surface. Halves of dentin specimens were irradiated with 3.5- and 4.5-W Er,Cr:YSGG lasers and with a 2-W Nd:YAG laser. The remaining halves served as controls. The microhardness measurements were recorded with a Vickers surface microhardness tester. The results were statistically evaluated by paired t test and one-way ANOVA (p?=?0.05). Laser irradiation has significantly reduced the microhardness of dentin within each group compared to its control. Moreover, statistically significant differences were observed among the different groups (p?<?0.05). The 3.5-W Er,Cr:YSGG laser produced the greatest reduction in microhardness of dentin followed by 4.5 W and Nd:YAG laser. The differences between all the groups were statistically significant. It was concluded that both laser devices used in this study have resulted in significant thermal damage and subsequent reduction in dentin microhardness values.     

Effects of Er:YAG and Nd:YAG laser irradiation on radicular dentine permeability using different irrigating solutions

BACKGROUND AND OBJECTIVES: To evaluate the effect of Er:YAG and Nd:YAG laser on radicular dentine permeability when using distilled and deionized water and 1% NaClO as irrigating solutions. STUDY DESIGN/MATERIALS AND METHODS: Thirty human maxillary canines were divided randomly into six groups. The root canals were instrumented with K files and the step-back technique. Group I, irrigation with distilled and deionized water; Group II, irrigation with 1% NaClO; Group III, irrigation with distilled and deionized water and Er:YAG laser application (140 mJ input, 61 mJ output 15 Hz, 300 pulses, and 42 J); Group IV, irrigation with 1% NaClO and Er:YAG laser application (same parameters as Group III); Group V, irrigation with distilled and deionized water and Nd:YAG laser application (150 mJ, 15 Hz, 2,25 W); Group VI, irrigation with 1% NaClO and Nd:YAG laser application (same parameters as Group V). During laser application the teeth were always filled with the irrigating solution. The tip was withdrawn gently in helicoidal movement from the apex to the cervical portion. The teeth were processed for histochemical evaluation. RESULTS: The Tukey test showed that the cervical and middle thirds were statistically similar (P > 0.05) and significantly greater than the apical third (P < 0.05). The Scheffé test showed significantly greater dentine permeability in root canals in which water and Er:YAG laser were used and were significantly different from the other treatments (P < 0.05). CONCLUSIONS: The use of distilled and deionized water and Er:YAG laser showed the greater increase of dentine permeability. The use of 1% NaClO with Nd:YAG laser, distilled, and deionized water with Nd:YAG laser and the use of water increased dentine permeability less than the other groups. The use of 1% NaClO with and without Er:YAG laser application were positioned intermediately among the treatments.     

Theoretical limits to soft-tissue damage by Er:YAG and Ho:YAG lasers

A significant advantage of Er:YAG and Ho:YAG laser radiation is that it can be transmitted efficiently by fibre, unlike that of the CO2 laser. The important characteristic of excisions made by these mid-infrared-beam lasers is the depth of coagulation beneath the excised surface. Intuitive physical arguments are developed to predict the coagulation depths, which are estimated to be 12mand 650 m for Er:YAG and Ho:YAG lesions respectively. These values are in agreement with derivations using more sophisticated physics by the same author elsewhere.     

Effect of dental surface treatment with Nd:YAG and Er:YAG lasers on bond strength of resin composite to recently bleached enamel

The aim of this work is to evaluate the effect of surface treatment with Er:YAG and Nd:YAG lasers on resin composite bond strength to recently bleached enamel. In this study, 120 bovine incisors were distributed into two groups: group C: without bleaching treatment; group B: bleached with 35% hydrogen peroxide. Each group was divided into three subgroups: subgroup N: without laser treatment; subgroup Nd: irradiation with Nd:YAG laser; subgroup Er: irradiation with Er:YAG laser. The adhesive system (Adper Single Bond 2) was then applied and composite buildups were constructed with Filtek Supreme composite. The teeth were sectioned to obtain enamel-resin sticks (1 × 1 mm) and submitted to microtensile bond testing. The data were statistically analyzed by the ANOVA and Tukey tests. The bond strength values in the bleached control group (5.57 MPa) presented a significant difference in comparison to the group bleached and irradiated with Er:YAG laser (13.18 MPa) or Nd:YAG (25.67 MPa). The non-bleached control group presented mean values of 30.92 MPa, with statistical difference of all the others groups. The use of Nd:YAG and Er:YAG lasers on bleached specimens was able to improve the bond strengths of them.     

Ablation of polymethylmethacrylate by Ho:YAG,Nd:YAG,and Erb:YAG lasers

Ho:YAG, Nd:YAG, and Erb:YAG laser ablation of Polymethylmethacrylate (PMMA) was investigated under in vitro and simulated clinical conditions. Ablation rates were measured for all lasers and after ablation, macroscopic and microscopic appearance of the ablation site was investigated. The mean ablation rates of the Erb:YAG, Ho:YAG, and Nd:YAG laser increased from 8 μm per pulse at 100 mJ to 44 μm per pulse at 300 mJ from 100 μm per pulse at 200 mJ to 222 μm per pulse at 800 mJ and from 28 μm per pulse at 100 mJ to 189 μm per pulse at 800 mJ, respectively. Macroscopic investigation exhibited melting of bone cement for the Ho:YAG and Nd:YAG lasers and pulse-to-pulse vaporization for the Erb:YAG laser. The width of thermal alteration, however, was comparable for all lasers used. Removal of cement from bone specimens under simulated clinical conditions showed good detachment of cement when the fiber was used parallel; in case of perpendicular use, remainders of cement and carbonization of bone could be observed upon histological investigation. © 1993 Wiley-Liss, Inc.     

Influence of the spatial beam profile on hard tissue ablation Part I: Multimode emitting Er:YAG lasers

Uniform dosimetry is a prerequisite for reproducible laser applications in research and practice. The light–tissue interaction is dependent on the absorbed energy (J) per unit of time () in the case of pulsed lasers, and on the absorbed power (W) per unit of volume (e.g. mm³) in the case of continuous-wave (cw) lasers, and thus directly dependent on the energy distribution within the laser beam. Consequently, precise knowledge of the spatial beam profile, and of the pulse duration and treatment time, is indispensable. The objective of this paper was a theoretical study of the impact of different mode profiles on energy distribution in the beam. Also examined was the question of the influence of changes in the laser parameters on the mode structure. Three erbium:YAG lasers (=2.94 m) were used for this purpose. The transversal mode structure of the lasers was observed by irradiating thermal paper and verified by means of calculations. The effect induced in the mode profile by changing the pulse energy and pulse repetition rate was investigated. The results of the tests show that changes in the laser parameters result in jumps in the transversal modes and associated energy distributions in the beam. The experiments confirm that simply changing the transversal modes has a substantial effect on the threshold energy required for the ablation of dental enamel (50 mJ with TEM₀₀, 22.6 mJ with TEM₃₁). In practice, inhomogeneity makes it impossible to determine the irradiated area in order to calculate the energy or power density. In addition, the energy distribution in the beam changes as a result of variation of the laser output energy and the pulse repetition rate. Consequently, simply measuring the beam diameter yields a totally incorrect result for the applied flux density when using a beam profile with a relatively high mode.     

Comparative evaluation of the effects of Nd:YAG and Er:YAG laser in dentin hypersensitivity treatment

Dentin hypersensitivity (DH) is one of the most common complications that affect patients after periodontal therapy. So far, many investigators have successfully used different types of laser on DH treatment. The aim of this study was to evaluate the comparative effect of Nd:YAG laser and Er:YAG laser on human teeth desensitization. A group of nine patients with a total of 63 chronic hypersensitive teeth were selected. Each one of them should at least have three hypersensitive teeth. These teeth were randomly allocated into three groups. Group 1, Nd:YAG laser (1 W, 15 Hz, 60 s, two times); group 2, Er:YAG laser (100 mJ, 3 Hz, 60 s, two times); and group 3 serves as control group without any treatment. Assessment of pain was performed by a visual analysing scale (VAS) after stimulation of sensitive tooth by using the sharp tip of an explorer. This test was performed before treatment, immediately after that and at 1-, 3- and 6-month intervals after treatment by one blinded examiner. Analysis of VAS score between the three groups at the time of treatment did not show any significant difference (p = 0.506). However, by using repeated-measurement analysis of variance test, significant differences were seen in the three groups between before-treatment VAS score and after treatment (p < 0.0005). This statistically significant difference in the control group demonstrated a placebo effect. However, the effect of using Nd:YAG and Er:YAG lasers was stronger than this placebo effect, so that after removing the effect of the placebo, differences immediately after, 1, 3 and 6 months post treatment between all three groups still were statistically highly significant (p < 0.0005). Compared to the Er:YAG laser group, using Nd:YAG laser resulted in a significant reduction of VAS score at each follow-up examination (p < 0.0005). Although using Nd:YAG and Er:YAG laser in desensitization of hypersensitive teeth showed a placebo effect limited to a short time, results of this study demonstrated that both of these lasers have an acceptable therapeutic effect. The observed effects seemed to last for at least 6 months. It was concluded that Nd:YAG laser is more effective than Er:YAG laser in reduction of patients’ pain.     

Comparison of Er:YAG and 9.6-microm TE CO(2) lasers for ablation of skull tissue

BACKGROUND AND OBJECTIVE: Craniotomy by using a drill and saw frequently results in fragmentation of the skull plate. Lasers have the potential to remove the skull plate intact, simplifying the reconstructive surgery. STUDY DESIGN/MATERIALS AND METHODS: Transverse-excited CO(2) lasers operating at the peak absorption wavelength of bone (lambda = 9.6 microm) and with pulse durations of 5-8 microsec, approximately the thermal relaxation time in hard tissue, produced high ablation rates and minimal peripheral thermal damage. Both thick (2 mm) and thin (250 microm) bovine skull samples were perforated and the ablation rates calculated. Results were compared with Q-switched and free-running Er:YAG lasers (lambda = 2.94 microm, tau(p) = 0.5 microsec and 300 microsec). RESULTS: The CO(2) laser produced ablation rates of up to 60 and 15 microm per pulse for thin and thick sections, respectively, and perforated thin and thick sections with fluences of less than 1 J/cm(2) and 6 J/cm(2), respectively. There was no discernible thermal damage and no need for water irrigation during ablation. Pulse durations > or =20 microsec resulted in significant tissue charring, which increased with the pulse duration. Although the free-running Er:YAG laser produced ablation rates of up to 100 microm per pulse, fluences of 10 J/cm(2) and 30 J/cm(2) were required to perforate thin and thick samples, respectively, and peripheral thermal damage measured 25-40 microm. CONCLUSIONS: In summary, the novel 5- to 8-microsec pulse length of the TE CO(2) laser is long enough to avoid a marked reduction in the ablation rate due to plasma formation and short enough to avoid peripheral thermal damage through thermal diffusion during the laser pulse. Furthermore, in vivo animal studies with the TE CO(2) laser are warranted for potential clinical application in craniotomy and craniofacial procedures.     

Effects of Er:YAG and Er,Cr:YSGG lasers on dentine hypersensitivity. Short-term clinical evaluation

Dentine hypersensitivity (DH) is a painful condition and is a clinical challenge due to the different treatment strategies available. High-intensity lasers have been studied as a possible option. The aim of this randomized, controlled, double-blind clinical study was to evaluate the effects of Er:YAG and Er,Cr:YSGG lasers on DH. The study group comprised 28 subjects who met the inclusion criteria. A visual analogue scale was used to quantify sensitivity before treatment as baseline, immediately before and immediately after treatment, and 1 week and 1 month after treatment. Teeth were assigned to four groups: group 1 control (no treatment), group 2 Er:YAG laser treatment (2 Hz/32.4 mJ/5.9 J/cm(2)), group 3 Er,Cr:YSGG laser treatment (0.25 W/4.4 J/cm(2)), and group 4 Er,Cr:YSGG laser treatment (0.50 W/ 8.9 J/cm(2)). Data were collected and submitted to statistical analysis for both evaporative (air) and mechanical (probe) stimulation. For both the air and probe stimulation no differences were observed between the pretreatment sensitivities. With the evaporative stimulus, the pain level immediately after treatment was reduced; however, after this the values remained stable. Irradiation with the Er:YAG laser was associated with the lowest level of pain. With the mechanical stimulus, group 4 showed the most pronounced decrease in pain immediately after treatment; however, by the end of the study, pain levels had increased. Groups 1, 2 and 3 showed a reduction in pain that was significantly different from that in group 4 after the 4 weeks of clinical follow up. Based on the results and within the limits of this study, it can be concluded that none of the laser treatments studied was capable of completely eliminating pain, but the Er:YAG and Er,Cr:YSGG lasers are suitable for the treatment of DH.     

Nd:YAG laser-induced hyperthermia treatment of spontaneously occurring veterinary head and neck tumors

Conventional hyperthermia treatment of superficial tumors in the oral cavity is troublesome due to difficulty in accessing the lesion. A new hyperthermia technique employing near-infrared radiation delivered through a flexible silica optical fiber is described. The system consisted of an Nd:YAG laser for tissue heating, a He-Ne laser for aiming beam, a computer-controlled optical shutter, an interstitial thermometer, computer, and a printer. A 3-m-long 600-microns silica fiber delivered laser energy to the tumor via surface illumination. Using the aiming beam, the spot size was adjusted to include 5 mm of surrounding normal tissue. A thermocouple implanted in the tumor base provided temperature feedback to maintain desired hyperthermic temperature within the lesion. Three spontaneously occurring canine (two squamous cell carcinomas on the gum, one pigmented melanoma on the hard palate) and one feline tumor (squamous cell carcinoma on the nose) have been treated with Nd:YAG laser hyperthermia. Hyperthermia was delivered at 43.5 degrees C for 1 h. All animals received standard radiation treatment prior to hyperthermia. Nd:YAG laser hyperthermia allowed effective and efficient delivery of heat to veterinary nasal and oral lesions otherwise not treatable with conventional heating techniques.