Effect of Different Cooling Strategies on Surface Quality and Power Consumption in Finishing End Milling of Stainless Steel 316

In this paper, an experimental investigation into the machinability of AISI 316 alloy during finishing end milling operation under different cooling conditions and with varying process parameters is presented. Three environmental-friendly cooling strategies were utilized, namely, dry, minimal quantity lubrication (MQL) and MQL with nanoparticles (Al₂O₃), and the variable process parameters were cutting speed and feed rate. Power consumption and surface quality were utilized as the machining responses to characterize the process performance. Surface quality was examined by evaluating the final surface roughness and surface integrity of the machined surface. The results revealed a reduction in power consumption when MQL and MQL + Al₂O₃ strategies were applied compared to the dry case by averages of 4.7% and 8.6%, respectively. Besides, a considerable reduction in the surface roughness was noticed with average values of 40% and 44% for MQL and MQL + Al₂O₃ strategies, respectively, when compared to the dry condition. At the same time, the reduction in generated surface roughness obtained by using MQL + Al₂O₃ condition was marginal (5.9%) compared with using MQL condition. Moreover, the results showed that the improvement obtained in the surface quality when using MQL and MQL + Al₂O₃ coolants increased at higher cutting speed and feed rate, and thus, higher productivity can be achieved without deteriorating final surface quality, compared to dry conditions. From scanning electron microscope (SEM) analysis, debris, furrows, plastic deformation irregular friction marks, and bores were found in the surface texture when machining under dry conditions. A slight smoother surface with a nano-polishing effect was found in the case of MQL + Al₂O₃ compared to the MQL and dry cooling strategies. This proves the effectiveness of lubricant with nanoparticles in reducing the friction and thermal damages on the machined surface as the friction marks were still observed when machining with MQL comparable with the case of MQL + Al₂O₃.     

Corrosion Resistance and Surface Bioactivity of Ti6Al4V Alloy after Finish Turning under Ecological Cutting Conditions

The influence of cooling conditions and surface topography after finish turning of Ti6Al4V titanium alloy on corrosion resistance and surface bioactivity was analyzed. The samples were machined under dry and minimum quantity lubrication (MQL) conditions to obtain different surface roughness. The surface topographies of the processed samples were assessed and measured using an optical profilometer. The produced samples were subjected to electrochemical impedance spectroscopy (EIS) and corrosion potential tests (E_corr) in the presence of simulated body fluid (SBF). The surface bioactivity of the samples was assessed on the basis of images from scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analysis. The inspection of the surfaces of samples after turning under dry and MQL conditions revealed unevenly distributed precipitation of hydroxyapatite compounds (Ca/P) with a molar ratio in the range of 1.73–1.97. Regardless of the cutting conditions and surface roughness, the highest values of E_corr ~0 mV were recorded on day 7 of immersion in the SBF solution. The impedance characteristics showed that, compared to the MQL conditions, surfaces machined under dry conditions were characterized by greater resistance and the presence of a passive layer on the processed surface. The main novelty of the paper is the study of the effect of ecological machining conditions, namely, dry and MQL cutting on the corrosion resistance and surface bioactivity of Ti6Al4V titanium alloy after finish turning. The obtained research results have practical significance. They can be used by engineers during the development of technological processes for medical devices made of Ti6Al4V alloy to obtain favorable functional properties of these devices.     

Surface Integrity and Tool Wear Analysis on Turning of Copper-Nickel 70/30 ASTM B122 Alloy under Low Initial Lubrication

Traditional flood lubrication in machining processes is considered an unsustainable technique. In this paper, the low initial lubrication (LIL) technique is analysed during turning of cupronickel 70/30 alloy, in terms of surface roughness. A tribological analysis has been developed on a pin-on-disk tribometer comparing different lubrication systems, obtaining comparative results of friction and tool wear. It has been found that the tool wear is 73% lower in comparison to flood lubrication. LIL technique shows the ability to reduce the friction coefficient compared to dry machining and leads to improve tool wear in comparison with flood lubrication. The surface integrity evaluation of machined parts finds that the LIL technique can improve the surface roughness under specific machining conditions.     

Experimental Study on High-Speed Milling of SiCf/SiC Composites with PCD and CVD Diamond Tools

Silicon carbide fiber reinforced silicon carbide ceramic matrix composite (SiC_f/SiC composite) is characterized by a high strength-to-density ratio, high hardness, and high temperature resistance. However, due to the brittleness of the matrix material and the anisotropy of the reinforcing phase, it is a huge challenge for machining of the material. The milling method has advantages of a high material removal rate and applicability to complex surface geometry. However, no published literature on milling of SiC_f/SiC composite has been found up to now. In this paper, high-speed milling of SiC_f/SiC composites was carried out under dry conditions and cryogenic cooling using liquid nitrogen, respectively. Polycrystalline diamond (PCD) and chemical vapor deposition (CVD) diamond cutting tools were used for the milling work. The cutting performance of the two kinds of tools in high-speed milling of SiC_f/SiC composites was studied. Tool failure modes and mechanisms were analyzed. The effects of the cooling approach on tool wear and machined surface quality were also investigated. The experimental results showed that under identical cutting parameters and cooling approaches, the PCD tool yielded better cutting performance in terms of a longer tool life and better surface quality than that of the CVD diamond tool. In dry machining, the failure modes of the CVD diamond tool were a large area of spalling on the rake face, edge chipping and severe tool nose fracture, whereas for the PCD tool, only a small area of spalling around the tool nose took place. Compared to the dry machining, the wear magnitudes of both PCD and CVD diamond tools were decreased in cryogenic machining. Additionally, the surface quality also showed significant improvements. This study indicates that the PCD tool is highly suitable for machining of SiC_f/SiC composite, and that the cryogenic method can improve machining efficiency and surface quality.     

Performance Assessment of Minimum Quantity Castor-Palm Oil Mixtures in Hard-Milling Operation

The necessity to progress towards sustainability has inspired modern researchers to examine the lubrication and cooling effects of vegetable oils on conventional metal cutting operations. Consequently, as an eco-friendly vegetable product, castor oil can be the right choice as Minimum quantity lubrication (MQL) base fluid. Nonetheless, the high viscosity of castor oil limits its flowability and restricts its industrial application. Conversely, palm oil possesses superior lubricity, as well as flowability characteristics. Hence, an attempt has been made to improve the lubrication behavior of castor oil. Here, six castor-palm mixtures (varying from 1:0.5–1:3) were utilized as MQL-fluid, and the values of machining responses viz. average surface roughness, specific cutting energy, and tool wear were evaluated. Furthermore, an integrated Shannon’s Entropy-based Technique for order preference by similarity to ideal solution (TOPSIS) framework was employed for selecting the most suitable volume ratio of castor-palm oil mixture. The rank provided by the TOPSIS method confirmed that 1:2 was the best volume ratio for castor-palm oil mixture. Afterward, a comparative analysis demonstrated that the best castor-palm volume fraction resulted in 8.262 and 16.146% lowering of surface roughness, 5.459 and 7.971% decrement of specific cutting energy, 2.445 and 3.155% drop in tool wear compared to that of castor and palm oil medium, respectively.     

Optimization of the Dry Turning Process of Ti48Al2Cr2Nb Aluminide Based on the Cutting Tool Configuration

Titanium aluminides are one of the most promising materials in aeronautical and automotive applications. However, their low machinability makes the processing of these alloys quite difficult under sustainability conditions, specially without lubrication. The current study focuses on the turning process of the Ti48Al2Cr2Nb gamma titanium aluminide under dry conditions. As far as we are aware, dry cutting is the most sustainable feature, although it has not been traditionally applied on titanium aluminides due to the accelerated tool wear that the material promotes. The main novelty of this work consists of providing a simple solution for reducing the tool wear based on the inclination of the cutting insert, what is evaluated in terms of tool wear and tool life, cutting forces, cutting temperature, surface integrity of the machined part, as well as its microhardness and microstructural effects. The results shown here clearly point out a better performance of the machining process. This fact could be understood if we take into consideration that an increment of the clearance angle from 6.3° to 11.6° and 15° increases the tool life by five and six times, respectively, using efficient cutting speeds, whose values have increased by 50% with respect to the original cutting conditions. This improvement is explained according to the reduction in the cutting temperature and friction forces in the flank face of the tool. In addition, the use of uncoated carbide inserts may lead to a better behaviour than the coated ones, considering the results obtained for a PVD TiAlN + AlCr₂O₃ coated insert herein researched.     

Hybrid nano-fluid-minimum quantity lubrication strategy for machining austempered ductile iron (ADI)

The use of austempered ductile iron (ADI) is rapidly increasing in many engineering applications such as automotive due to its unique and promising characteristics, for example; high strength to weight ratio, high wear and corrosion resistance, high yield stress, and high toughness. However, other properties such as low thermal conductivity undesirably affects ADI machinability and accelerate cutting tool failure. Additionally, other issues associated with cutting ADI are the high cutting temperature, high pressure and dynamic loads, and tendency of chip to adhere to cutting tool face. To overcome such issues, a proper coolant should be applied. However, flood coolant has sufficient effects in reducing the generated cutting heat, further alternatives are still required to decease its environmental and health impacts. Minimum quantity lubrication (MQL) serves as the best alternative to flood cooling from an environmental perspective as it minimizes the amount of cutting fluid; however, its heat capacity is lower than the traditional flood coolant. To improve the cooling and lubricating efficiency of MQL, aluminum oxide (\(\hbox {Al}_{2}\hbox {O}_{3}\)) gamma nanoparticles are used in this work and its effect on the tool wear behavior during cutting of ADI is investigated. The combination of MQL-nanofluid at cutting speed of 120 m/min and feed rate of 0.2 mm/rev showed the best tool life, while test 3 which has been performed at cutting speed of 240 m/min and feed rate of 0.2 mm/rev using classical MQL provided the worst flank wear value.     

Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid

The enormous use of cutting fluid in machining leads to an increase in machining costs, along with different health hazards. Cutting fluid can be used efficiently using the MQL (minimum quantity lubrication) method, which aids in improving the machining performance. This paper contains multiple responses, namely, force, surface roughness, and temperature, so there arises a need for a multicriteria optimization technique. Therefore, in this paper, multiobjective optimization based on ratio analysis (MOORA), VIseKriterijumska Optimizacija I Kompromisno Resenje (VIKOR), and technique for order of preference by similarity to ideal solution (TOPSIS) are used to solve different multiobjective problems, and response surface methodology is also used for optimization and to validate the results obtained by multicriterion decision-making technique (MCDM) techniques. The design of the experiment is based on the Box–Behnken technique, which used four input parameters: feed rate, depth of cut, cutting speed, and nanofluid concentration, respectively. The experiments were performed on AISI 304 steel in turning with minimum quantity lubrication (MQL) and found that the use of hybrid nanofluid (Alumina–Graphene) reduces response parameters by approximately 13% in forces, 31% in surface roughness, and 14% in temperature, as compared to Alumina nanofluid. The response parameters are analyzed using analysis of variance (ANOVA), where the depth of cut and feed rate showed a major impact on response parameters. After using all three MCDM techniques, it was found that, at fixed weight factor with each MCDM technique, a similar process parameter was achieved (velocity of 90 m/min, feed of 0.08 mm/min, depth of cut of 0.6 mm, and nanoparticle concentration of 1.5%, respectively) for optimum response. The above stated multicriterion techniques employed in this work aid decision makers in selecting optimum parameters depending upon the desired targets. Thus, this work is a novel approach to studying the effectiveness of hybrid nanofluids in the machining of AISI 304 steel using MCDM techniques.     

Laser-Assisted High Speed Machining of 316 Stainless Steel: The Effect of Water-Soluble Sago Starch Based Cutting Fluid on Surface Roughness and Tool Wear

Laser-assisted high speed milling is a subtractive machining method that employs a laser to thermally soften a difficult-to-cut material’s surface in order to enhance machinability at a high material removal rate with improved surface finish and tool life. However, this machining with high speed leads to high friction between workpiece and tool, and can result in high temperatures, impairing the surface quality. Use of conventional cutting fluid may not effectively control the heat generation. Besides, vegetable-based cutting fluids are invariably a major source of food insecurity of edible oils which is traditionally used as a staple food in many countries. Thus, the primary objective of this study is to experimentally investigate the effects of water-soluble sago starch-based cutting fluid on surface roughness and tool’s flank wear using response surface methodology (RSM) while machining of 316 stainless steel. In order to observe the comparison, the experiments with same machining parameters are conducted with conventional cutting fluid. The prepared water-soluble sago starch based cutting fluid showed excellent cooling and lubricating performance. Therefore, in comparison to the machining using conventional cutting fluid, a decrease of 48.23% in surface roughness and 38.41% in flank wear were noted using presented approach. Furthermore, using the extreme learning machine (ELM), the obtained data is modeled to predict surface roughness and flank wear and showed good agreement between observations and predictions.     

Low and High Speed Orthogonal Cutting of AA6061-T6 under Dry and Flood-Coolant Modes: Tool Wear and Residual Stress Measurements and Predictions

The present research work aimed to study the effects of cutting environments and conditions on tool wear and residual stresses induced by orthogonal cutting of AA6061-T6. Cutting environments included dry- and flood-coolant modes and cutting conditions consisted of cutting speed and feed rate. A 2D finite element (FE) model was developed to predict tool wear and residual stresses and was validated by experimental measurements including machining forces, tool wear, and residual stresses. This was obtained by exploring various magnitudes of the shear friction factor and heat transfer coefficient and choosing proper coefficients using the calibration of the predicted results with the measured ones. The experimental results showed that the effect of cutting environment including dry and flood-coolant modes was negligible on machining forces. The experimental investigation also demonstrated that increasing feed rate raised machining forces, tool wear and residual stresses in both cutting environments. Low Speed Cutting (LSC) led to the highest value of tool wear and High Speed Cutting (HSC) provided the lowest values of resultant machining forces and residual stresses in both modes. Flood-coolant mode reduced tool wear and slightly decreased tensile residual stresses in comparison with dry mode. As a result, low feed rate and high-speed cutting under flood-coolant mode were proposed in order to improve tool wear and residual stress in orthogonal cutting of AA6061-T6.     

Progressing towards Sustainable Machining of Steels: A Detailed Review

Machining operations are very common for the production of auto parts, i.e., connecting rods, crankshafts, etc. In machining, the use of cutting oil is very necessary, but it leads to higher machining costs and environmental problems. About 17% of the cost of any product is associated with cutting fluid, and about 80% of skin diseases are due to mist and fumes generated by cutting oils. Environmental legislation and operators’ safety demand the minimal use of cutting fluid and proper disposal of used cutting oil. The disposal cost is huge, about two times higher than the machining cost. To improve occupational health and safety and the reduction of product costs, companies are moving towards sustainable manufacturing. Therefore, this review article emphasizes the sustainable machining aspects of steel by employing techniques that require the minimal use of cutting oils, i.e., minimum quantity lubrication, and other efficient techniques like cryogenic cooling, dry cutting, solid lubricants, air/vapor/gas cooling, and cryogenic treatment. Cryogenic treatment on tools and the use of vegetable oils or biodegradable oils instead of mineral oils are used as primary techniques to enhance the overall part quality, which leads to longer tool life with no negative impacts on the environment. To further help the manufacturing community in progressing towards industry 4.0 and obtaining net-zero emissions, in this paper, we present a comprehensive review of the recent, state of the art sustainable techniques used for machining steel materials/components by which the industry can massively improve their product quality and production.     

Surface Finish and Residual Stresses Induced by Orthogonal Dry Machining of AA7075-T651

The surface finish was extensively studied in usual machining processes (turning, milling, and drilling). For these processes, the surface finish is strongly influenced by the cutting feed and the tool nose radius. However, a basic understanding of tool/surface finish interaction and residual stress generation has been lacking. This paper aims to investigate the surface finish and residual stresses under the orthogonal cutting since it can provide this information by avoiding the effect of the tool nose radius. The orthogonal machining of AA7075-T651 alloy through a series of cutting experiments was performed under dry conditions. Surface finish was studied using height and amplitude distribution roughness parameters. SEM and EDS were used to analyze surface damage and built-up edge (BUE) formation. An analysis of the surface topography showed that the surface roughness was sensitive to changes in cutting parameters. It was found that the formation of BUE and the interaction between the tool edge and the iron-rich intermetallic particles play a determinant role in controlling the surface finish during dry orthogonal machining of the AA7075-T651 alloy. Hoop stress was predominantly compressive on the surface and tended to be tensile with increased cutting speed. The reverse occurred for the surface axial stress. The smaller the cutting feed, the greater is the effect of cutting speed on both axial and hoop stresses. By controlling the cutting speed and feed, it is possible to generate a benchmark residual stress state and good surface finish using dry machining.     

Anomalies in the Geometric Surface Structure of Shaped Elements Composed of Inconel 718 Alloy

This paper presents the results of investigation that was performed on shafts composed of Inconel 718. Tests were performed in dry and wet conditions. Cutting parameters, such as feed and depth of cut, were constant. The cutting speed was changed. The investigation was performed for various shaft shapes: cylindrical, taper 30°, taper 45°, and sphere. For that reason, the value of the angle between the machined surface and the cutting edge changed. The lowest values of the roughness parameters, Ra and Rz, were obtained for a larger value of the angle between the machined surface and cutting edge. The investigation showed that cutting speed, machining conditions (dry and wet machining), and the variable angle between the machined surface and the cutting edge influenced the surface roughness. Application of a higher cutting speed resulted in lower roughness values. Lower values of roughness parameters were obtained by wet machining.     

Geometry,Structure and Surface Quality of a Maraging Steel Milling Cutter Printed by Direct Metal Laser Melting

This article considers the use of additive manufacturing to produce cutting tools for various machining operations, especially turning, milling, and drilling. The right geometry and material of the tool as well as coatings applied on cutting edges are crucial as they improve the life and performance of the tool. The study described here focused on a four-flute end mill made of maraging steel 1.2709 using a Concept Laser M2 Cusing Direct Metal Laser Melting (DMLM) machine. Before the printed tool was first used, it was examined to determine its dimensional and geometric accuracy, surface roughness, and surface structure. The measurement data showed that the tool required machining, e.g., grinding, to improve its geometry because the total runout of the shank and the cutting edge radius were too high, amounting to 120 μm and 217 μm, respectively. The cutting edges were sharpened to obtain a fully functional cutting tool ready to perform milling operations. The study aimed to check the dimensional and geometric accuracy of the 3D printed milling cutter and determine the optimal machining allowance for its finishing.     

Experimental Investigation of Suitable Cutting Conditions of Dry Drilling into High-Strength Structural Steel

Dry machining is one of the main ways to reduce the environmental burden of the machining process and reduce the negative effect of the cutting fluid and aerosols on operators. In addition, dry machining can reduce overall machining costs and, in the case of large workpieces, reduce the extra work associated with removing residual cutting fluid from the workpiece and adjacent area. For high-strength structural steel products, it is typical to drill holes with larger diameters of around 20 mm. Therefore, this work is devoted to the investigation of the dry drilling process carried out on a workpiece made of S960QL steel with a helical drill with a diameter of 21 mm. The aim was to find suitable cutting conditions for dry drilling with regard to process stability and workpiece quality. An experiment performed with a coolant served as a comparison base. A dry drilling experiment was performed with cutting speeds from 30 to 70 m·min⁻¹ and feeds from 0.1 to 0.3 mm·rev⁻¹, and with the results of this experiment, the same experiment with flood cooling was performed. During the drilling process, spindle torque values were recorded using the indirect spindle current recording method. The macroscopic chip morphology was studied to understand the cutting process. The chip thickness ratio was measured, as well as the maximum diameter of spiral chips. On the final workpiece, the qualitative and dimensional parameters of the holes were evaluated, such as the diameter, cylindricity and surface roughness, depending on the change in the cutting conditions and cutting environment. Evaluation of the obtained data led to the following conclusions. When drilling the S960QL material, there is only a very small increase in the drilling torque during dry drilling compared to drilling with cutting fluid. The increase in friction demonstrated by the chip thickness coefficient is significant. The influence of the environment on the dimensional accuracy showed a tendency for a slight increase in the holes’ diameters during dry machining. In comparison, the cylindricity of the dry-drilled holes shows a lower deviation than the holes drilled with cutting fluid. The surface roughness of the holes after dry drilling is affected by the increased friction of the outgoing chips, despite the resulting parameters being very good due to the drilling technology standards. This work provides a comprehensive view of the dry drilling process under defined conditions, and the results represent suitable cutting conditions to achieve a stable cutting process and a suitable quality of drilled holes.     

An Experimental and Finite Element Approach for a Better Understanding of Ti-6Al-4V Behavior When Machining under Cryogenic Environment

Due to increasing demand in manufacturing industries, process optimization has become a major area of focus for researchers. This research optimizes the cryogenic machining of aerospace titanium alloy Ti-6Al-4V for industrial applications by studying the effect of varying the nozzle position using two parameters: the nozzle’s separation distance from the tool–chip interface and its inclination angle with respect to the tool rake face. A finite element model (FEM) and computational fluid dynamics (CFD) model are used to simulate the cryogenic impingement of cryogenic carbon dioxide on the tool–workpiece geometry. Experiments are conducted to evaluate cutting forces, tool wear, and surface roughness of the workpiece, and the results are related to the CFD and FEM analyses. The nozzle location is shown to have a significant impact on the cutting temperatures and forces, reducing them by up to 45% and 46%, respectively, while the dominant parameter affecting the results is shown to be the separation distance. Cryogenic machining is shown to decrease adhesion-diffusion wear as well as macroscopic brittle chipping of the cutting insert compared to dry turning, while the workpiece surface roughness is found to decrease by 44% in the case of cryogenic machining.     

The Influence of the Depth of Grinding on the Condition of the Surface Layer of 20MnCr5 Steel Ground with the Minimum Quantity Lubrication (MQL) Method

This paper describes the research on abrasive machining conditions and their influence on microhardness and residual stresses distribution in the technological surface layer of 20MnCr5 steel. The roughness of ground samples was also measured. Samples underwent a vacuum carburizing process (LPC) followed by high-pressure gas quenching (HPGQ) in a 4D quenching chamber. Processes were realized with a single-piece flow method. Then, the flat surfaces of samples were ground with a Vortex type IPA60EH20VTX alumina grinding wheel using a flat-surface grinder. The samples were ground to three depths of grinding (a_e = 0.01; 0.02; 0.03 mm) with grinding fluid supply using either flood method (WET) or minimum quantity lubrication (MQL) method. The condition of the technological surface layer was described using microhardness and residual stresses, as well as some selected parameters of surface roughness. The results obtained revealed that changes in microhardness as compared to microhardness of the material before grinding were lower in samples ground with grinding fluid supplied with MQL method. At the same time, the values of residual stresses were also better for samples ground using MQL method. Furthermore, the use of grinding fluid fed with MQL method produced lower values of surface roughness compared to the parameters obtained with WET method. It was concluded that for the tested scope of machining conditions, the MQL method can be a favourable alternative to the flood method of supplying grinding fluid into the grinding zone.     

Tool Wear Effect on Surface Integrity in AISI 1045 Steel Dry Turning

In the present work, the surface integrity and flank wear of uncoated cermet inserts in dry turning of AISI 1045 steel were evaluated. Three-dimensional techniques were used to assess the surface roughness. Previously, finite element analysis was carried out to predict the cutting forces and heat distribution in the chip formation region. Cutting speed and feed were the parameters varied in the experiments. Feed is decisive in the final quality of the turned surface and cutting speed had little influence on this aspect. The surface was significantly damaged with the progression of the insert flank wear. Considering an average flank wear VB_B of 0.1 mm, a tool life of 35 min was achieved using a cutting speed of 175 m/min, and of 23 min for a cutting speed of 275 m/min. Abrasive wear was predominant during the experiments. No microstructure defects were observed, as well as crack propagation or accentuated deformations near the machined surface region. Therefore, the dry turning of 1045 steel with cermet inserts route has proven extremely viable from the standpoints of tool life, surface integrity, chip formation, and sustainability.     

Optimisation on the Performance of Bubble-Bursting Atomisation for Minimum Quantity Lubrication with Vegetable Oil Using Computational Fluid Dynamics Simulation

Sustainable and green machining technologies have become a welcomed topic in the manufacturing industries. One of the emerging sustainable technologies is minimum quantity lubrication (MQL). In this study, the optimisation and study of the bubble-bursting atomisation system applied to MQL machining is carried out through the computational fluid dynamics (CFD) simulation approach. Vegetable oil is selected as the cooling lubricant in this study. The performance of the bubble-bursting atomisation system is improved by alternating air inlet velocity and the gap distance between the inlets of bubble production. A velocity of 0.1 ms⁻¹ is suitable for the air at the inlets for the bubble production, whereas 10 ms⁻¹ is suitable for the velocity of the air at the inlet, where the droplets of vegetable oil are guided to the nozzle. Besides that, a 50 mm gap distance between the air inlets for the production of bubbles is able to avoid the occurrence of bubble coalescence. Under these conditions, optimal bubble sizes of 2–3 mm can be achieved, with a higher probability of nano-sized droplets being present in these ranges. Furthermore, a higher rate and smaller size of vegetable oil droplets escaping the atomisation chamber and reaching the machining zone will be generated. Thus, the performance of the MQL machining can be improved.     

Experimental Study on the Dry Drilling Nickel-Based Superalloy of CrAlYN Coated Carbide Bit

Nickel-based superalloy is regarded as one of the materials with the poorest cutting and drilling performance. Additionally, there is much less research on the drilling of it. This paper aims to study the drilling performance of dry drilling nickel-based superalloy with uncoated and CrAlYN coated carbide bit. First of all, the primary and secondary factors influencing the machining performance of dry drilling nickel-base superalloy uncoated carbide bit were explored through an orthogonal test. Secondly, the self-prepared CrAlYN coated carbide drills, and uncoated drills were compared and analyzed from perspectives of service life, drilling force, drilling temperature, drill surface topography, failure mechanism, and machining surface quality. The research results are as follows: the drilling temperature is the primary factor affecting the drilling performance under dry drilling conditions. CrAlYN coating can obviously prolong the service life of tools, reduce the drilling force and drilling temperature, and improve the machining surface quality at lower rotational speeds. Moreover, the coated cemented carbide bit has a similar failure mode to the uncoated cemented carbide bit after the CrAlYN coating falls off in the wear zone of cemented carbide bit, which is mainly bonding wear on the rear tool surface and the front tool surface.