A quantitative in vitro method to predict the adhesion lifetime of diamond-like carbon thin films on biomedical implants

A quantitative method using Rockwell C indentation was developed to study the adhesion of diamond-like carbon (DLC) protective coatings to the CoCrMo biomedical implant alloy when immersed in phosphate-buffered saline (PBS) solution at 37 °C. Two kinds of coatings with thicknesses ranging from 0.5 up to 16 microns were investigated, namely DLC and DLC/Si-DLC, where Si-DLC denotes a 90 nm thick DLC interlayer containing Si. The time-dependent delamination of the coating around the indentation was quantified by means of optical investigations of the advancing crack front and calculations of the induced stress using the finite element method (FEM). The cause of delamination for both types of coatings was revealed to be stress-corrosion cracking (SCC) of the interface material. For the DLC coating a typical SCC behavior was observed, including a threshold region (60 J m^?2) and a “stage 1” crack propagation with a crack-growth exponent of 3.0, comparable to that found for ductile metals. The DLC/Si-DLC coating exhibits an SCC process with a crack-growth exponent of 3.3 and a threshold region at 470 J m^?2, indicating an adhesion in PBS at 37 °C that is about eight times better than that of the DLC coating. The SCC curves were fitted to the reaction controlled model typically used to explain the crack propagation in bulk soda lime glass. As this model falls short of accurately describing all the SCC curves, limitations of its application to the interface between a brittle coating and a ductile substrate are discussed.     

Hemocompatibility of surface-modified, silicon-incorporated, diamond-like carbon films

The hemocompatibility of plasma-treated, silicon-incorporated, diamond-like carbon (Si-DLC) films was investigated. Si-DLC films with a Si concentration of 2at.% were prepared on Si (100) or Nitinol substrates using a capacitively coupled radiofrequency plasma-assisted chemical vapor deposition method using a mixed gas of benzene (C(6)H(6)) and diluted silane (SiH(4):H(2)=10:90). The Si-DLC films were then treated with O(2), CF(4) or N(2) glow discharge for surface modification. The plasma treatment revealed an intimate relationship between the polar component of the surface energy and its hemocompatibility. All in vitro characterizations, i.e. protein absorption behavior, activated partial thromboplastin time measurement and platelet adhesion behavior, showed improved hemocompatibility of the N(2-)- or O(2)-plasma-treated surfaces where the polar component of the surface energy was significantly increased. Si-O or Si-N surface bonds played an important role in improving hemocompatibility, as observed in a model experiment. These results support the importance of a negatively charged polar component of the surface in inhibiting fibrinogen adsorption and platelet adhesion.     

Effect of nanofiber-coated surfaces on the proliferation and differentiation of osteoprogenitors in vitro

The osteoconductive property of titanium (Ti) surfaces is important in orthopedic and dental implant devices. Surface modifications of Ti have been proposed to further improve osseointegration. In this study, three different materials, silicon (Si), silicon oxide (SiO(2)), and titanium oxide (TiO(2)), were used to construct nanofibers for surface coating of Ti alloy Ti-6Al-4 V (Ti alloy). MC3T3-E1 osteoprogenitor cells were seeded on nanofiber-coated discs and cultured for 42 days. DNA, alkaline phosphatase, osteocalcin, and mineralization nodules were measured using PicoGreen, enzyme-linked immunosorbent assay, and calcein blue staining to detect the attachment, proliferation, differentiation, and mineralization of MC3T3-E1 cells, respectively. The results demonstrated that the initial cell attachments on nanofiber-coated discs were significantly lower, although cell proliferation on Si and SiO(2) nanofiber-coated discs was better than on Ti alloy surfaces. TiO(2) nanofibers facilitated a higher cellular differentiation capacity than Ti alloy and tissue culture-treated polystyrene surfaces. Thus, surface modification using nanofibers of various materials can alter the attachment, proliferation, and differentiation of osteoprogenitor cells in vitro.     

Wear-corrosion performance of Si-DLC coatings on Ti-6Al-4V substrate

Si-incorporated diamond-like carbon (Si-DLC) coatings ranging from 0 to 2 at % Si were deposited on Ti-alloy substrate by means of radio frequency plasma-assisted chemical vapor deposition (r.f. PACVD) technique, using a mixture of benzene (C(6)H(6)) and silane (SiH(4)) as the reaction gas. The synergy in wear and corrosion of Si-DLC coatings was investigated by tribological and electrochemical techniques. The electrolyte used in this test to simulate the corrosive environment of body fluid was a 0.89 wt % NaCl solution of pH 7.4 at 37 degrees C. This study provides quantitative data for the assessment of the effect of Si incorporation on the synergistic effect between wear and corrosion in the simulated body fluid environment. In conclusion, tribological and electrochemical measurements showed that the Si-DLC films could improve wear-corrosion resistance in the simulated body fluid environment owing to the lower friction coefficient, corrosion rate, delamination area, and water uptake.     

Abrasive waterjet peening: a new method of surface preparation for metal orthopedic implants

Abrasive waterjet (AWJ) peening is a new mechanical surface treatment process envisioned for use on metal orthopedic implants. The process utilizes an abrasive waterjet to simultaneously texture and work harden the surface of a metal substrate through controlled hydrodynamic erosion. In this study, a titanium alloy (Ti6Al4V) was subjected to AWJ peening over a range of parametric conditions. The textured surfaces were quantified in terms of the apparent interdigitation volume (V(i)), the effective stress concentration factor (K(t)) posed by the surface topography, and the magnitude of residual stress (sigma(r) ). Topographical features of the prepared surfaces were determined using contact profilometry, and X-ray diffraction was used in evaluating the in-plane residual stress. It was found that a large range in V(i) (9.4-43.8 microm(3)/microm(2)) and K(t) (1.3-2.7) are available through selection of the AWJ peening process parameters. Furthermore, a compressive residual stress (-409 +/- sigma(r) +/- -33) was found to result within the surface of the Ti6Al4V substrates regardless of treatment conditions. When compared to a titanium plasma spray coating used for cementless fixation, the AWJ peened Ti6Al4V exhibited a surface topography with significantly lower effective stress concentration and higher compressive residual stress. Based on results from this study, AWJ peening may serve as a new method of surface treatment for metal orthopedic implants, which supports the development of stable primary fixation and simultaneously enhances the component fatigue strength.     

Electrophoretic deposition of bioactive silica-calcium phosphate nanocomposite on Ti-6Al-4V orthopedic implant

Bioactive silica-calcium phosphate nanocomposite (SCPC) has been coated on Ti-6Al-4V implant employing an electrophoretic deposition (EPD) technique. The effects of composition and pH of the suspending medium on the zeta potential of three different SCPC formulations; SCPC25, SCPC50 and SCPC75 were analyzed. The average zeta potential of SCPC50 in pure ethanol was more negative than that of SCPC25 or SCPC75; however, the difference was not statistically significant. Discs of Ti-6Al-4V were passivated, coated with SCPC50 (200 nm-10 μm) and thermally treated at 600-800°C to produce a coating thickness in the range of 43.1 ± 5.7 to 30.1 ± 4.6 μm. After treatment at 600, 700, and 800°C, the adhesion strength at the SCPC50/Ti-6Al-4V interface was 42.6 ± 3.6, 44.7 ± 8.7, and 47.2 ± 4.3 MPa, respectively. SEM-EDX analyses of SCPC50-coated Ti-6Al-4V preimmersed in PBS for 7 days showed the formation of a Ca-deficient hydroxyapatite surface layer. ICP-OES analyses of the immersing solution (n = 6) showed an increase in the ionic concentration of Si from 3.3 ± 0.9 to 5.0 ± 1.2 ppm between days 1 and 4; after which no significant change in the Si concentration was measured. Bone marrow mesenchymal stem cells attached to the SCPC50-coated implants expressed significantly higher (p < 0.05) alkaline phosphatase activity (82.4 ± 25.6 nmoles p-NP/mg protein/min) than that expressed by cells attached to HA-coated or uncoated implants. Results of the study suggest that bioactive SCPC50 can efficiently be coated on Ti-6Al-4V using EPD. The SCPC50 coating has the potential to enhance bone integration with the orthopedic implant.     

The effect of non-specific interactions on cellular adhesion using model surfaces

The contribution of non-specific interactions between cells and model functional surfaces was measured using a spinning disc apparatus. These model functional surfaces were created using self-assembled monolayers (SAM) of alkylsilanes terminated with epoxide, carboxyl (COOH), amine (NH(2)), and methyl (CH(3)) groups. These SAMs were characterized using ellipsometry, atomic force microscopy, contact angle goniometry, and X-ray photoelectron spectroscopy to confirm the presence of well-formed monolayers of expected physicochemical characteristics. All substrates also demonstrated excellent stability under prolonged exposure (up to 18 h) to aqueous conditions. The adhesion strength of K100 erythroleukemia cells to the functional substrates followed the trend: CH(3) < COOH approximately epoxide < NH(2). The NH(2) SAM surface exhibited nearly an order of magnitude greater adhesion strength than the other SAMs and this non-specific effect exceeded the adhesion measured when RGD tri-peptides were also immobilized on the surface. These findings illustrate the importance of substrate selection in quantitative studies of peptide-mediated cellular adhesion.     

Effect of hydrogen peroxide on titanium surfaces: in situ imaging and step-polarization impedance spectroscopy of commercially pure titanium and titanium, 6-aluminum, 4-vanadium

To analyze titanium's response to representative surgical wound environments, a study was conducted on commercially pure titanium (CPTi) and titanium, 6-aluminum, 4-vanadium (Ti-6Al-4V) exposed to phosphate-buffered saline (PBS) with 30 mM of hydrogen peroxide (H(2)O(2)) added. The study was characterized by simultaneous electrochemical atomic force microscopy (EC AFM) and step-polarization impedance spectroscopy (SPIS). Surfaces were covered with protective oxide domes that indicated topography changes with potential and time of immersion. Less oxide dome coarsening was noted on surfaces treated with PBS containing H(2)O(2) than on surfaces exposed to pure PBS. Electrical data deduced from current transients collected while stepping voltage between 0 V and 1 V indicated that charge transfer in hydrogen peroxide solutions was an order of magnitude larger than it was in pure PBS. Oxide (early) resistances of CPTi samples were higher than were Ti-6Al-4V oxide resistances in both types of solutions, but CPTi oxide resistance was lower in the hydrogen peroxide solution compared to pure PBS. Capacitance data suggest that CPTi oxide films thicken in hydrogen peroxide solution more than they do in pure PBS. Differences in electrical properties between CPTi and Ti-6Al-4V surfaces suggest that CPTi, but not Ti-6Al-4V, has catalytic activity on H(2)O(2) and that the catalytic activity of CPTi oxide affects its ability to grow TiO(2). Differences in electrical properties are related to catalytic and oxidative mechanisms that take place directly on the titanium oxide surface and in wound environments. The study provides a foundation and theoretic basis for the porous oxide model on commercially pure titanium exposed to hydrogen peroxide.     

The MTT assays of bovine retinal pericytes and human microvascular endothelial cells on DLC and Si-DLC-coated TCPS

MTT (Tetrazolium)-assay suggests that diamond-like carbon (DLC) and silicon-doped DLC (Si-DLC) films obtained under appropriate deposition parameters are not toxic to bovine retinal pericytes, and human microvascular endothelial cells (HMEC). The observed frequency distributions of the optical density (OD) values indicative of cell viability are near Gaussian-normal distribution. One-way ANOVA indicates that at 0.05 levels the population means are not significantly different for the coated and control samples. The observed OD values depend on the cell line (cell growth/metabolic rate), possibly cell cycle stage, the deposition parameters-bias voltage, ion energy, pressure, argon precleaning, and the dopant. For colored thin films like DLC with room temperature photoconductivity and photoelectric effects, it is important to account for the OD contribution from the coating itself. MTT assay, not surprisingly, seems not to be highly sensitive to interfacial cellular interaction resulting from the change in the film's nanostructure, because the tetrazolium metabolism is mainly intracellular and not interfacial. The thin films were synthesized by 13.56 MHz RF-PECVD using argon and acetylene as source gases, with tetramethylsilane (TMS) vapor introduced for silicon doping. This study could be relevant to biomedical application of the films in the eye, peri-vascular, vascular compartments, and for cell-tissue engineering.     

Initial responses of human osteoblasts to sol-gel modified titanium with hydroxyapatite and titania composition

Sol-gel thin films of hydroxyapatite (HA) and titania (TiO(2)) have received a great deal of attention in the area of bioactive surface modification of titanium (Ti) implants. Sol-gel coatings were developed on Ti substrates of pure HA and TiO(2) and two composite forms, HA+10% TiO(2) and HA+20% TiO(2), and the biological properties of the coatings were evaluated. All the coating layers exhibited thin and homogeneous structures and phase-pure compositions (either HA or TiO(2)). Primary human osteoblast cells showed good attachment, spreading and proliferation on all the sol-gel coated surfaces, with enhanced cell numbers on all the coated surfaces relative to uncoated Ti control at day 1, as observed by MTT assay and scanning electron microscopy. Cell attachment rates were also enhanced on the pure HA coating relative to control Ti. The pure HA and HA+10% TiO(2) composite coating furthermore enhanced proliferation of osteoblasts at 4 days. Moreover, the gene expression level of several osteogenic markers including bone sialoprotein and osteopontin, as measured by RT-PCR at 24h, was shown to vary according to coating composition. These findings suggest that human primary bone cells show marked and rapid early functional changes in response to HA and TiO(2) sol-gel coatings on Ti.     

Effect of wettability and surface functional groups on protein adsorption and cell adhesion using well-defined mixed self-assembled monolayers

Self-assembled monolayers (SAMs) of alkanethiols, which can provide flat and chemically well-defined surfaces, were employed as model surfaces to understand cellular interaction with artificial materials. SAMs presenting a wide range of wettabilities were prepared by mixing two kinds of alkanethiols carrying terminal methyl (CH(3)), hydroxyl (OH), carboxylic acid (COOH), or amino (NH(2)) groups. Adhesion behavior of human umbilical vein endothelial cells (HUVECs) and HeLa cells on these mixed SAMs were examined. The number of adhered HUVECs reached a maximum on CH(3)/OH mixed SAMs with a water contact angle of 40 degrees , while cell adhesion increased with decreasing water contact angle up to 60-70 degrees and then leveled off on CH(3)/COOH and CH(3)/NH(2) mixed SAMs. Numbers of adhered HeLa cells showed a maximum on CH(3)/OH and CH(3)/COOH mixed SAMs with a water contact angle of 50 degrees . These facts suggest that cell adhesion is mainly determined by surface wettability, but is also affected by the surface functional group, its surface density, and the kinds of cells. The effect of exchange of adsorbed proteins on cell adhesion was also examined. HUVECs were cultured on the mixed SAMs preadsorbed with albumin. Cell adhesion was effectively prohibited on hydrophobic SAMs pretreated with albumin. Albumin strongly adsorbed and resisted replacement by cell adhesive proteins on hydrophobic SAMs. On the other hand, cells adhered to albumin-adsorbed hydrophilic SAMs. Displacement of preadsorbed albumin with cell adhesive proteins effectively occurs on these hydrophilic SAMs. This effect contributes to induce SAMs with moderate wettability to give suitable surfaces for cell adhesion.     

Surface chemistry modulates fibronectin conformation and directs integrin binding and specificity to control cell adhesion

Integrin-mediated cell adhesion to proteins adsorbed onto synthetic surfaces anchors cells and triggers signals that direct cell function. In the case of fibronectin (Fn), adsorption onto substrates of varying properties alters its conformation/structure and its ability to support cell adhesion. In the present study, self-assembled monolayers (SAMs) of alkanethiols on gold were used as model surfaces to investigate the effects of surface chemistry on Fn adsorption, integrin binding, and cell adhesion. SAMs presenting terminal CH(3), OH, COOH, and NH(2) functionalities modulated adsorbed Fn conformation as determined through differences in the binding affinities of monoclonal antibodies raised against the central cell-binding domain (OH > COOH = NH(2) > CH(3)). Binding of alpha(5)beta(1) integrin to adsorbed Fn was controlled by SAM surface chemistry in a manner consistent with antibody binding (OH > COOH = NH(2) > CH(3)), whereas alpha(V) integrin binding followed the trend: COOH > OH = NH(2) = CH(3), demonstrating alpha(5)beta(1) integrin specificity for Fn adsorbed onto the NH(2) and OH SAMs. Cell adhesion strength to Fn-coated SAMs correlated with alpha(5)beta(1) integrin binding (OH > COOH = NH(2) > CH(3)), and experiments with function-perturbing antibodies demonstrated that this receptor provides the dominant adhesion mechanism in this cell model. This work establishes an experimental framework to analyze adhesive mechanisms controlling cell-surface interactions and provides a general strategy of surface-directed control of adsorbed protein activity to manipulate cell function in biomaterial and biotechnological applications.     

A rebreathing method for measuring lung volume, diffusing capacity and cardiac output in conscious small animals

We developed a multiple gas rebreathing technique for measuring lung diffusing capacity (DL(CO)), lung volume (V(L)) and cardiac output simultaneously in conscious spontaneously breathing small animals. Lung volume was measured from the dilution of methane (CH4) or sulfur hexafluoride (SF6) and verified independently by a helium washout technique. Cardiac output and DL(CO) were estimated from the uptake of acetylene and carbon monoxide, respectively. We tested guinea pigs at two levels of alveolar oxygen tension in order to estimate membrane diffusing capacity and pulmonary capillary blood volume by the Roughton-Forster technique. Results show that measured DL(CO) are consistent with reported values in anesthetized guinea pigs as well as with allometric comparison across species. Lung volume estimated from SF6 dilution agreed closely with that estimated independently from helium washout; however, lung volume estimated from CH4 dilution was systematically lower due to the addition of endogenously produced CH4 to the rebreathing system. We conclude that this technique can be used to measure resting lung function in conscious unsedated small animals.     

Protein adsorption and platelet attachment and activation, on TiN, TiC, and DLC coatings on titanium for cardiovascular applications

The hemocompatibility of a TiN/TiC/diamond-like carbon (DLC) multilayer structure, deposited on titanium substrates for use as coatings for a heart valve prosthesis, has been studied through the adsorption of blood proteins and the adhesion and attachment of blood platelets. All of the surfaces were characterized by stylus profilometry and water contact angles. The adsorption of albumin and fibrinogen to the surfaces was assessed using the Amido Black assay, whereas platelet attachment was studied by scanning electron microscopy and quantified using stereological techniques. The degree of platelet spreading on the surfaces was seen to correlate with differences in surface energy, indicated from contact angle measurements. The greatest spreading was seen on the more hydrophilic surfaces. When studying protein adsorption to the surfaces, no correlation could be determined between contact angle results and levels of adsorption, although the most hydrophilic surfaces did appear to promote greater amounts of fibrinogen adsorption. Thrombus formation was observed to some degree on all of the surfaces, with the exception of the DLC coating. This coating also promoted less spreading of platelets than the other surfaces. The good hemocompatibility of the DLC coating is attributed to its hydrophobicity and smooth surface, resulting in a higher ratio of albumin to fibrinogen than any of the other surfaces.     

Retrospective lifetime estimation of failed and explanted diamond-like carbon coated hip joint balls

Diamond-like carbon (DLC) coatings are known to have extremely low wear in many technical applications. The application of DLC as a coating has aimed at lowering wear and to preventing wear particle-induced osteolysis in artificial hip joints. In a medical study femoral heads coated with diamond-like amorphous carbon, a subgroup of DLC, articulating against polyethylene cups were implanted between 1993 and 1995. Within 8.5 years about half of the hip joints had to be revised due to aseptic loosening. The explanted femoral heads showed many spots of local coating delamination. Several of these explanted coated TiAlV femoral heads have been analyzed to investigate the reason for this failure. Raman analysis and X-ray photoelectron spectroscopy (XPS) depth profiling showed that the coating consists of diamond-like amorphous carbon, several Si-doped layers and an adhesion-promoting Si interlayer. Focused ion beam (FIB) transverse cuts revealed that the delamination of the coatings is caused by in vivo corrosion of the Si interlayer. Using a delamination test set-up dissolution of the silicon adhesion-promoting interlayer at a speed of more than 100 μm year(-1) was measured in vitro in solutions containing proteins. Although proteins are not directly involved in the corrosion reactions, they can block existing small cracks and crevices under the coating, hindering the exchange of liquid. This results in a build-up of crevice corrosion conditions in the crack, causing a slow dissolution of the Si interlayer.     

Covalent surface modification of a titanium alloy with a phosphorylcholine-containing copolymer for reduced thrombogenicity in cardiovascular devices

Our objective was to develop a surface modification strategy for a titanium alloy (TiAl6V4) to provide thromboresistance for surfaces in rigorous blood-contacting cardiovascular applications, such as that found in ventricular assist devices. We hypothesized that this could be accomplished by the covalent attachment of a phospholipid polymer, poly(2-methacryloyloxyethylphosphorylcholine (MPC)-co-methacryl acid) (PMA). TiAl6V4 was H2O plasma treated by radio frequency glow discharge, silanated with 3-aminopropyltriethoxysilane (APS), and ammonia plasma treated to increase surface reactivity. The TiAl6V4 surface was then modified with PMA via a condensation reaction between the amino groups on the TiAl6V4 surface and the carboxyl groups on PMA. The surface composition was verified by X-ray photoelectron spectroscopy, confirming successful modification of the TiAl6V4 surfaces with APS and PMA as evidenced by increased Si and P. Plasma treatments with H2O and ammonia were effective at further increasing the surface reactivity of TiAl6V4 as evidenced by increased surface PMA. The adsorption of ovine fibrinogen onto PMA-modified surfaces was reduced relative to unmodified surfaces, and in vitro ovine blood contact through a rocking test revealed marked reductions in platelet deposition and bulk phase platelet activation relative to unmodified TiAl6V4 and polystyrene controls. The results indicate that the PMA-modification scheme for TiAl6V4 surfaces offers a potential pathway to improve the thromboresistance of the blood-contacting surfaces of cardiovascular devices.     

Corrosion behavior of cast Ti-6Al-4V alloyed with Cu

It has recently been found that alloying with copper improved the inherently poor grindability and wear resistance of titanium. This study characterized the corrosion behavior of cast Ti-6Al-4V alloyed with copper. Alloys (0.9 or 3.5 mass % Cu) were cast with the use of a magnesia-based investment in a centrifugal casting machine. Three specimen surfaces were tested: ground, sandblasted, and as cast. Commercially pure titanium and Ti-6Al-4V served as controls. Open-circuit potential measurement, linear polarization, and potentiodynamic cathodic polarization were performed in aerated (air + 10% CO(2)) modified Tani-Zucchi synthetic saliva at 37 degrees C. Potentiodynamic anodic polarization was conducted in the same medium deaerated by N(2) + 10% CO(2). Polarization resistance (R(p)), Tafel slopes, and corrosion current density (I(corr)) were determined. A passive region occurred for the alloy specimens with ground and sandblasted surfaces, as for CP Ti. However, no passivation was observed on the as-cast alloys or on CP Ti. There were significant differences among all metals tested for R(p) and I(corr) and significantly higher R(p) and lower I(corr) values for CP Ti compared to Ti-6Al-4V or the alloys with Cu. Alloying up to 3.5 mass % Cu to Ti-6Al-4V did not change the corrosion behavior. Specimens with ground or sandblasted surfaces were superior to specimens with as-cast surfaces.     

Self-assembled monolayers with different terminating groups as model substrates for cell adhesion studies

Cell shapes induced by cell-substratum interactions are linked with proliferation, differentiation or apoptosis of cells. To clarify the relevance of specific surface characteristics, we applied self-assembled monolayers (SAM) of alkyl silanes exhibiting a variety of terminating functional groups. We first characterised the SAMs on glass or silicon wafers by measuring wettability, layer thickness and roughness. Water contact angle data revealed that methyl (CH(3)), bromine (Br), and vinyl (CH=CH(2)) groups lead to hydrophobic surfaces, while amine (NH(2)) and carboxyl (COOH) functions lead to moderately wettable surfaces, and polyethylene glycol (PEG) and hydroxyl (OH) groups created wettable substrata. The surfaces were found to be molecular smooth except for one type of NH(2) surface. The SDS-PAGE analysis of proteins adsorbed from bovine serum to the SAMs showed less protein adsorption to PEG and OH than to CH(3), NH(2) and COOH. Immunoblotting revealed that a key component of adsorbed proteins is vitronectin while fibronectin was not detectable. The interaction of human fibroblasts with CH(3), PEG and OH terminated SAMs was similarly weak while strong attachment, spreading, fibronectin matrix formation and growth were observed on COOH and NH(2). The strong interaction of fibroblasts with the latter SAMs was linked to an enhanced activity of integrins as observed after antibody-tagging of living cells.     

Titanium containing amorphous hydrogenated carbon films (a-C: H/Ti): surface analysis and evaluation of cellular reactions using bone marrow cell cultures in vitro

Amorphous hydrogenated carbon (a-C : H) coatings, also called diamond-like carbon (DLC), have many properties required for a protective coating material in biomedical applications. The purpose of this study is to evaluate a new surface coating for bone-related implants by combining the hardness and inertness of a-C : H films with the biological acceptance of titanium. For this purpose, different amounts of titanium were incorporated into a-C : H films by a combined radio frequency (rf) and magnetron sputtering set-up. The X-ray photoelectron spectroscopy (XPS) of air-exposed a-C : H/titanium (a-C : H/Ti) films revealed that the films were composed of TiO2 and TiC embedded in and connected to an a-C : H matrix. Cell culture tests using primary adult rat bone marrow cell cultures (BMC) were performed to determine effects on cell number and on osteoblast and osteoclast differentiation. By adding titanium to the carbon matrix, cellular reactions such as increased proliferation and reduced osteoclast-like cell activity could be obtained, while these reactions were not seen on pure a-C : H films and on glass control samples. In summary, a-C : H/Ti could be a valuable coating for bone implants, by supporting bone cell proliferation while reducing osteoclast-like cell activation.     

Human microvascular endothelial cellular interaction with atomic N-doped DLC compared with Si-doped DLC thin films

This article reports results of endothelial cell interaction with atom beam source N-doped a-C:H (diamond-like carbon, DLC) as it compares with that of Si-doped DLC thin films. The RF plasma source exhibits up to 40% N-dissociation and N-atomic fluxes of approximately 0.85 x 10(18) atoms/s, which ensures better atomic nitrogen incorporation. Two different types of nitrogen species (with and without the use of sweep plates to remove charged ions) were employed for nitrogen doping. The number of attached endothelial cells is highest on Si-DLC, followed by the N-DLC (where the sweep plates were used to remove ions), the N-DLC (without the use of sweep plates), undoped DLC, and finally the uncoated sample. The contact angle values for these films suggest that water contact angle is higher in the atomic nitrogen neutral films and Si-DLC films compared to the ionized-nitrogen specie doped films and undoped DLC thin films, suggesting that the more hydrophobic films, semiconducting films, and film with relieved stress have better interaction with human microvascular endothelial cells. It seems evident that N-doping increases the Raman I(D)/I(G) ratios, whereas N-neutral doping decreases it slightly and Si-doping decreases it even further. In this study, lower Raman I(D)/I(G) ratios are associated with increased sp(3)/sp(2) ratio, an increased H concentration, photoluminescence intensity, and a higher endothelial cellular adhesion. These investigations could be relevant to biocompatibility assessment of nanostructured biomaterials and tissue engineering.