不同表面处理方式对氧化锆基全瓷崩瓷树脂修补剪切强度的影响

目的：比较不同表面处理方式对氧化锆基底材料与复合树脂粘接剪切强度的影响。方法：将60个钇稳定氧化锆（Y-TZP）试件分为6组,分别接受酸蚀、喷砂、硅烷偶联剂、酸蚀＋硅烷偶联剂、喷砂＋硅烷偶联剂5种表面处理,未处理组作为对照。在处理面粘接复合树脂,经24 h水浴后测试剪切强度。扫描电子显微镜（SEM）观察处理面微观形态。结果：喷砂组（A）（33.45±3.46）MPa、喷砂＋硅烷偶联剂组（AS）（36.95±2.93）MPa两组剪切强度值明显高于其他组（P〈0.01）;未处理组（N）、8%HF酸蚀组（H）、硅烷偶联剂组（S）、8%HF酸蚀＋硅烷偶联剂组（HS）组间剪切强度无统计学差异。相同处理方式下,加入与不加人硅烷偶联剂组间剪切强度无统计学差异。SEM观察酸蚀处理对Y-TZP表面形貌无改变,喷砂处理明显粗化Y-TZP表面。结论：喷砂处理能够有效提高Y-TZP与复合树脂粘接强度;酸蚀及硅烷偶联剂对Y-TZP处理无效。     

Nd:YAG激光表面处理对树脂粘接剂与氧化锆粘接强度影响的meta分析

目的:试用Meta分析研究Nd:YAG激光表面处理对树脂粘接剂与氧化锆粘接强度的影响,为提高树脂粘接剂与氧化锆的粘接强度提供循证证据。方法:通过计算机检索PubMed、Cochran Library、EMbase、CNKI、维普、万方等数据库,查找Nd:YAG激光表面处理氧化锆的相关研究,采用RevMan5.2软件对纳入的研究进行Meta分析。结果:共纳入8个研究,合计290个样本。Meta分析结果显示:Nd:YAG激光表面处理组与对照组比较,剪切粘接强度（P=0.02）和粗糙度（P=0.0001）均高于对照组,差异有统计学意义;Nd:YAG激光表面处理组的剪切粘接强度与Al₂O₃喷砂组比较,差异无统计学意义（P=0.87）,Nd:YAG激光表面处理组的粗糙度高于Al₂O₃喷砂组,差异有统计学意义（P=0.02）。结论:Nd:YAG激光表面处理能增加树脂粘接剂与氧化锆的粘接强度,但目前尚不能认为Nd:YAG激光表面处理优于Al₂O₃喷砂处理。     

Er:YAG激光和Nd:YAG激光辅助的牙漂白对树脂充填体粘接强度和边缘微渗漏的影响

目的：评价Er:YAG激光和Nd:YAG激光辅助的牙漂白对釉质表面树脂充填体粘接强度和边缘微渗漏的影响。方法：将离体牙制备成釉质测试试件（n=64）后随机分为4组（n=16），包括对照组、传统漂白组、Er:YAG激光辅助的漂白组和Nd:YAG激光辅助的漂白组。4组试件分别处理后，检测其釉质表面树脂充填体的剪切粘接强度（n=8）和微渗漏深度（n=8），利用体视显微镜观察各组试件的断裂模式。采用SPSS 26.0软件包对数据进行统计学分析。结果：与对照组相比，传统漂白后釉质表面树脂充填体的粘接强度显著下降，边缘微渗漏显著增加(P<0.05);Er:YAG激光辅助的漂白后釉质表面充填体的剪切粘接强度和微渗漏深度与对照组相比无显著差异（P>0.05）,Nd:YAG激光辅助的漂白后树脂充填体的剪切粘接强度显著下降（P<0.05），但其边缘微渗漏深度与对照组相比无显著差异(P>0.05)。4组试件的粘接断裂模式主要为粘接界面断裂。结论：相比传统漂白方法，激光辅助的牙漂白对树脂充填体粘接强度和微渗漏的影响较小，具有一定的临床优势。     

瓷面处理对金属托槽与瓷面粘接性能的影响

目的　研究瓷表面不同处理方法对金属托槽与瓷修复体的粘接强度及去粘接后瓷面完整性的影响。方 法　根据使用粘接剂和表面处理方法的不同,将80个瓷面随机分为8组,每组10个瓷面。分别用京津釉质粘接剂 和光固化复合树脂粘接,表面处理分别行37%磷酸酸蚀、9·6%氢氟酸酸蚀、打磨去釉、瓷面涂硅烷偶联剂4种表面 处理法。试件粘接托槽后经37℃恒温水浴24 h后测定抗剪切强度,记录去粘接后的瓷面破裂情况。对磷酸酸蚀, 氢氟酸酸蚀、打磨去釉的瓷面进行扫描电镜观察。结果　采用氢氟酸酸蚀、打磨去釉、硅烷偶联剂组的粘接抗剪切 强度明显高于磷酸酸蚀组(P<0·01)。打磨去釉后用光固化复合树脂粘接及氢氟酸酸蚀或瓷表面涂硅烷处理后使 用任意一种粘接材料粘接均取得有效的粘接强度。各组去粘接后的瓷破裂率无显著性差异(P>0·05)。结论　氢 氟酸酸蚀、打磨去釉、瓷面涂硅烷偶联剂均可以明显增加金属托槽与瓷面之间的粘接抗剪切强度。瓷面涂硅烷偶 联剂是金属托槽与瓷面粘接时良好的表面处理剂。     

Nd:YAG激光对水门汀与牙本质剪切强度的影响

目的:评价脉冲Nd:YAG激光对水门汀与牙本质间剪切强度的影响,并观察激光照射前后的牙本质表面结构变化。方法:取人前磨牙30个,暴露牙本质粘接面形成60个测试样本,随机分为激光组和对照组。激光组以0.8W、10Hz脉冲Nd:YAG激光照射牙本质表面25sec,联合3种水门汀充填;对照组直接使用3种水门汀充填于牙本质表面,置于37℃生理盐水24h后,测试剪切强度,并进行统计学分析,在根管显微镜下观察断裂模式并分类。扫描电镜观察激光照射前后的牙本质表面形态。结果:聚羧酸锌组、玻璃离子组和树脂加强玻璃离子组在Nd:YAG激光照射前(后)的剪切强度分别为4.63±1.39(4.77±0.97)MPa、5.15±0.67(5.26±1.21)MPa和0.92±0.46(0.99±0.35)MPa,激光照射前后的差别均无统计学意义(P>0.05)。扫描电镜观察,0.8W、10Hz的Nd:YAG激光照射会使牙本质表面熔融,玷污层基本去除,大部分牙本质小管封闭,且在局部会出现裂纹。结论:Nd:YAG激光(0.8W、10Hz)处理牙本质,对聚羧酸锌和玻璃离子水门汀与牙本质间的粘接强度无影响。     

Nd: YAG激光对3种树脂水门汀与牙本质粘接强度的影响

目的观察Nd: YAG激光照射前后树脂水门汀-牙本质粘接界面的微观形貌特征,评价Nd: YAG激光对3种树脂水门汀与牙本质间粘接强度的影响。方法选择人离体前磨牙30颗,分为颊、舌两部分,将试件随机分为激光组和对照组。激光组以0.8 W、10 Hz脉冲Nd: YAG激光作用于牙本质表面25 s,联合3种树脂水门汀RelyX ARC、Panavia F和RelyX Unicem充填;对照组直接使用树脂水门汀充填。然后测试剪切强度,在根管显微镜下观察断裂模式并分类。另选人离体前磨牙6颗,按照标准的牙本质粘接面预备后,使用Nd: YAG激光照射3颗牙牙本质表面,并联合充填不同的树脂水门汀,用扫描电镜观察Nd: YAG激光照射前后树脂水门汀-牙本质界面的微观形貌变化。结果
激光照射可以提高自酸蚀树脂水门汀Panavia F和自粘接树脂水门汀RelyX Unicem与牙本质之间的剪切强度（P＜0.05）。激光会降低全酸蚀树脂水门汀RelyX ARC与牙本质间的剪切强度（P＜0.05）。根管显微镜下观察可见：试件断裂大部分发生在树脂水门汀-牙本质界面。扫描电镜观察可见：Nd: YAG激光照射后,全酸蚀亚组和自酸蚀亚组的混合层变薄、树脂突变短且少;自粘接亚组变化不明显,未见树脂突。结论Nd: YAG激光照射后,可提高Panavia F和RelyX Unicem与牙本质的剪切强度,建议临床联合应用。     

Nd:YAG激光根管清理对纤维桩粘接效果的影响

目的：利用钕钇铝石榴石（Nd:YAG）激光进行根管清理，探讨其对纤维桩粘接效果的影响。方法：36颗完整离体单根管牙，统一截冠后进行根管预备，依据不同的处理方法分为对照组、Nd-Ⅰ期组及Nd-Ⅰ+Ⅱ期组，对照组进行常规根管预备，Nd-Ⅰ期组与Nd-Ⅰ+Ⅱ期组采用Nd:YAG激光处理根管，其余同对照组。各组行根管充填，随后对照组及Nd-Ⅰ期组行常规桩道预备，Nd-Ⅰ+Ⅱ期组桩道预备后再次进行Nd:YAG激光处理，扫描电镜下观察处理后根管牙本质表面形貌。3组样本经纤维桩粘接后制备1.0 mm厚的横切薄片，行推出实验并记录各组样本的纤维桩剪切粘接强度，并通过扫面电镜观察粘接界面。结果：Nd:YAG激光可有效去除根管内玷污层，促进牙本质小管开放。Nd-Ⅰ期组及Nd-Ⅰ+Ⅱ期组进入牙本质小管内的树脂突的数目和深度优于对照组，桩剪切粘接强度也显著高于对照组（P<0.01），但Nd-Ⅰ期组及Nd-Ⅰ+Ⅱ期组桩粘接强度未见显著性差异（P>0.05）。结论：根管治疗过程中采用Nd:YAG激光清理根管，可取得较好的牙本质清洁效果，有利于提高纤维桩的粘接强度。     

2种激光对硬化牙本质粘接强度影响的实验研究

目的比较2种不同激光对硬化牙本质与复合树脂粘接强度的影响。方法选择牙本质视觉分级3级以上牙面磨损的后牙30颗,按照随机数字表法随机分为Er,Cr:YSGG激光处理组(E组)、Nd:YAG激光处理组(N组)和对照组,联合Adper Prompt L-Pop处理、Z350复合树脂充填,置于37℃生理盐水中24 h,制作微拉伸试件并进行微拉伸粘接强度测试。采用SPSS13.0软件对微拉伸粘接强度值进行单因素方差分析。结果 E组粘接强度(24.71±3.13)MPa,N组粘接强度(21.72±2.36)MPa,对照组粘接强度(18.61±2.01)MPa。E组的粘接强度最高,3组之间相比较差异均有统计学意义(P<0.05)。体视显微镜观察结果发现断裂多发生于牙本质-树脂粘接界面。结论 Er,Cr:YSGG激光和Nd:YAG激光均能够提高硬化牙本质与复合树脂的粘接强度,且Er,Cr:YSGG激光处理后获得的粘接强度更高。     

脉冲Nd:YAG激光影响复合树脂修补烤瓷粘接强度实验研究

目的：评价激光进行瓷面处理对复合树脂修补烤瓷的粘接效果。方法：分别用８％氢氟酸及３组能量参数的脉冲Ｎｄ：ＹＡＧ激光（１５Ｈｚ、４０ｍＪ、０．６Ｗ;１５Ｈｚ、６０ｍＪ、０．９Ｗ;１５Ｈｚ、８０ｍＪ、１．２Ｗ）对烤瓷牙粘接表面进行照射,照射时间均为１ｍｉｎ,涂硅烷液及活化剂后,粘接复合树脂。应用电子万能试验机测试复合树脂－烤瓷的抗剪切粘接强度。采用扫描电镜观察瓷处理面的形貌特征。结果：激光０．６Ｗ组、０．９Ｗ组、１．２Ｗ组及酸蚀组的抗剪切粘接强度分别为８．６１、１４．０７、１１．２２及１３．４７ＭＰａ,激光０．６Ｗ组明显低于酸蚀组,两者具有统计学差异,而０．９Ｗ组及１．２Ｗ组与酸蚀组则无显著性差异。扫描电镜显示经激光处理的瓷面粗糙不平,呈浅凹状及火山口状结构。结论：在适当能量参数下,脉冲Ｎｄ：ＹＡＧ激光可代替酸蚀进     

不同表面处理方法对纳米复合陶瓷与树脂水门汀粘接强度的影响

目的 评估不同表面处理对纳米复合陶瓷与树脂水门汀剪切粘接强度的影响。方法 将纳米复合陶瓷用计算机辅助设计/计算机辅助制作（CAD/CAM）技术切割成大小为10 mm×10 mm×3 mm的试件150块,并根据表面处理方法不同将试件按随机数字表的方法随机分为5组（n=30）：对照组、喷砂组、喷砂+硅烷组、酸蚀组和酸蚀+硅烷组。各组试件经过相应表面处理后,使用Single Bond Universal通用粘接剂+RelyX ^TM Ultimate Cliker ^TM树脂水门汀将树脂试件粘接于纳米复合陶瓷试件上,37 ℃蒸馏水中水浴24 h和30 d,万能试验机进行剪切粘接强度测试。结果 不同表面处理方法、不同的水浴时间都会影响到剪切粘接强度。喷砂+硅烷组的剪切粘接强度最大,与其他各组间差异均具有统计学意义（P<0.05）;对照组和酸蚀组间差异无统计学意义,但两组与其他组间差异具有统计学意义（P<0.05）;喷砂组和酸蚀+硅烷组之间差异无统计学意义（P>0.05）,但两组与其他组间差异具有统计学意义（P<0.05）。结论 喷砂、喷砂+硅烷、酸蚀+硅烷对纳米复合陶瓷表面处理,均可提高其与树脂水门汀的剪切粘接强度,喷砂+硅烷处理后剪切粘接强度最佳。     

Er:YAG激光照射对牙本质粘结强度的影响

目的探讨Er:YAG激光照射对牙本质粘结强度的影响。方法选取离体磨牙或前磨牙40颗,随机分为4组:A:酸蚀(35%磷酸)组;B:Er:YAG激光组;C:Er:YAG激光+磷酸酸蚀组;D:空白对照组。每组随机选取2颗制备成3 mm厚的牙本质盘,相应预处理后扫描电镜观察;每组剩余8颗牙制备统一标准粘结面,相应预处理后与树脂粘结测量剪切粘结强度。结果扫描电镜结果显示牙本质面经相应预处理后发生明显改变;统计分析结果显示A组剪切粘结强度最大(16.03±6.56)MPa,其次为C组(13.21±6.08)MPa,两组间差异无统计学意义(P>0.05);D组剪切粘结强度最低(4.52±1.02)MPa,与B组(7.91±4.56)MPa比较差异无统计学意义(P>0.05),与A、C组比较差异有统计学意义(P<0.05)。结论 Er:YAG激光照射联合磷酸酸蚀较单纯Er:YAG激光照射可提高牙本质剪切粘结强度。     

Shear bond strength of a new self-adhering flowable composite resin for lithium disilicate-reinforced CAD/CAM ceramic material

PURPOSE

The purpose of this study was to evaluate and compare the effects of different surface pretreatment techniques on the surface roughness and shear bond strength of a new self-adhering flowable composite resin for use with lithium disilicate-reinforced CAD/CAM ceramic material.

MATERIALS AND METHODS

A total of one hundred thirty lithium disilicate CAD/CAM ceramic plates with dimensions of 6 mm × 4 mm and 3 mm thick were prepared. Specimens were then assigned into five groups (n=26) as follows: untreated control, coating with 30 µm silica oxide particles (Cojet™ Sand), 9.6% hydrofluoric acid etching, Er:YAG laser irradiation, and grinding with a high-speed fine diamond bur. A self-adhering flowable composite resin (Vertise Flow) was applied onto the pre-treated ceramic plates using the Ultradent shear bond Teflon mold system. Surface roughness was measured by atomic force microscopy. Shear bond strength test were performed using a universal testing machine at a crosshead speed of 1 mm/min. Surface roughness data were analyzed by one-way ANOVA and the Tukey HSD tests. Shear bond strength test values were analyzed by Kruskal-Wallis and Mann-Whitney U tests at α=.05.

RESULTS

Hydrofluoric acid etching and grinding with high-speed fine diamond bur produced significantly higher surface roughness than the other pretreatment groups (P<.05). Hydrofluoric acid etching and silica coating yielded the highest shear bond strength values (P<.001).

CONCLUSION

Self-adhering flowable composite resin used as repair composite resin exhibited very low bond strength irrespective of the surface pretreatments used.     

Influence of water flow rate on shear bond strength of resin composite to Er:YAG cavity preparation

PURPOSE: To evaluate in vitro the influence of water flow rate on shear bond strength of a resin composite to enamel and dentin after Er:YAG cavity preparation. METHODS: Ten bovine incisors were selected and roots removed. Crowns were sectioned in four pieces, resulting in 40 samples that were individually embedded in polyester resin (n = 10), and ground to plane the enamel and expose the dentin. The bonding site was delimited and samples were randomly assigned according to cavity preparation: (1) Er:YAG/1.0 mL/minute; (2) Er:YAG/1.5 mL/minute; (3) Er:YAG/2.0 mL/minute and (4) High speed handpiece/bur (control group). Samples were fixed to a metallic device, where composite resin cylinders were prepared. Subsequently, they were stored for 24 hours and subjected to a shear bond strength test (500N at 0.5 mm/minute). RESULTS: Means (MPa) were: enamel: 1: 12.8; 2: 16.8; 3: 17.5; 4: 36.0 and Dentin: 1: 13.6; 2: 18.7; 3: 12.1; 4: 21.3. Data were submitted to ANOVA and Tukey's test. Adhesion to enamel was more efficient than for dentin. The cavities prepared with conventional bur (control) presented higher statistically significant bond strength values (P < 0.05) than for Er:YAG laser for both enamel and dentin. No significant differences were observed between water flow rates employed during enamel ablation. For dentin, the shear bond strength of 2.0 mL/minute water flow rate was lower than for 1.5 mL/minute and 1.0 mL/minute rates. The Er:YAG laser adversely affected shear bond strength of resin composite to both enamel and dentin, regardless of the water flow rate used.     

Influence of Different Surface Pretreatments of Zirconium Dioxide Reinforced Lithium Disilicate Ceramics on the Shear Bond Strength of Self-Adhesive Resin Cement

AimTo analyze the influence of different surface pretreatments of zirconium dioxide reinforced lithium disilicate ceramics on the shear bond strength of self-adhesive resin cement.Materials and methodsEighty-four zirconium reinforced lithium disilicate disc Vita suprinity (Vita Zahnfabrick, Bad Säckingen, Germany) 14x12x2 mm specimens were fabricated according to the manufacturer''s recommendations. The specimens were embedded in acrylic resin blocks and randomly divided in seven groups (n=12/each) accorrding to the treatment: Group 1- 10% hydrofluoric acid; Group 2- silane; Group 3- hydrofluoric and silane; Group 4- sandblasting with silane; Group 5- Er: YAG laser+ silane; Group 6- Nd: YAG laser + silane; and the control group, in which the specimens were not treated. Round shape composite discs (Filtek Bulk fill, 3M ESPE, St.Paul, Minnesota, USA) with 3.5 mm diameter, were made for shear bond strength testing, and then cemented to the ceramic sample surface using composite cement (RelyX U200 Automix, 3M ESPE, Neuss, Germany). After cementing the composite disc on the sample, the samples were subjected to shear bond strength test of 10 N with a “stress rate” of 1 MPa / s. To determine the nature of the fracture (adhesive, cohesive or adhesive-cohesive), the broken samples were examined under a stereomicroscope. The ANOVA test and the Tukey test were used to compare the values ​​of the bond strength characteristics between different types of materials. All tests were performed with a significance level of α = 0.05.ResultsThere was a significant difference in the shear bond strength of self-adhesive cement to dental lithium-disilicate ceramics reinforced with zirconium dioxide after different preparation protocols (p<0, 05). The treatment of lithium disilicate ceramics reinforced with zirconium dioxide by silanization, sandblasting + silanization, Nd: YAG + silanization resulted in significantly higher bond strength compared to the control group. There was statistically higher bond strength of self-adhesive cement after pretreatment of lithium disilicate ceramics Nd: YAG + silanization compared to Er: YAG + silanization (p <0.05). Adhesive fracture dominated in the control group, sandblasting + silanization group, and in the laser groups, while mixed fracture dominated in other groups.ConclusionUnder the limitations of this study, the Nd:YAG irradiation with silanization could be used as pretreatment for providing greater shear bond strength of self-adhesive resin cement to zirconium reinforced lithium disilicate.     

不同参数激光处理根管对纤维桩粘结强度影响的实验研究

目的:研究不同参数Er:YAG激光处理根管壁牙本质对纤维桩粘结强度的影响,为激光临床应用提供参考。方法:收集60颗人类上颌中切牙,根据不同处理方法随机分为5组;空白对照组;3 W-50 μs Er:YAG激光组;3 W-100 μs Er:YAG 激光组;4.5 W-50 μs Er:YAG激光组;4.5 W-100 μs Er:YAG激光组,每组12颗。离体牙根管预备,充填,桩道预备后,Bisco树脂加强型纤维桩通过RelyX^TM Unicem粘结树脂水门汀粘固于根管内。流水状态下慢速锯将纤维桩外周平行片切,再垂直粘结面片于试件1 mm、4 mm、7 mm处切成三段1.0 mm×1.0 mm的长方形柱状试件,进行微拉伸强度测试。不同根管处理方法与牙根不同区域微拉伸强度均数采用两因素方差分析(α=0.05)。电镜下进行断裂类型分析,组件不同类型断裂率采用χ²检验(α=0.05)。 结果:3 W10-100 μs Er:YAG组拉伸强度值最高(5.55±0.97) MPa,与对照组(4.06±1.22) MPa相比较差异有显著性(P＜0.05) 。根管上部和中部粘结强度高于根管下部,差异有显著性(P＜0.05)。结论:Er:YAG激光处理牙本质表面对其与纤维桩粘结强度的影响与激光功率大小和脉冲持续时间有关,3 W-100 μs Er:YAG激光处理表面可以显著增强纤维桩与根管牙本质的粘结强度。     

Adhesion between glass fiber posts and resin cement: evaluation of bond strength after various pre-treatments

Purpose. To evaluate surface roughness and bond strength of glass fiber posts to a resin cement after various surface treatments. Materials and methods. Sixty individually formed glass fiber posts with a diameter of 1.5 mm and a length of 20 mm were used for this study. They were randomly assigned to six groups of pre-treatment (n = 10/group): Group C, untreated (control); Group SB, sandblasted; Group SC, silica coated; Group HF, hydrofluoric acid-etched; Group N, Nd:YAG laser irradiated; Group E, Er:YAG laser irradiated. Surface roughness of the posts was measured before and after pre-treatment. The posts were then bonded to resin cement and tensile bond strengths were determined in a universal testing machine. For statistical analysis, two-way ANOVA and post-hoc comparison tests (α = 0.05) were performed. Results. The highest bond strength value was observed in group HF, followed by group SC. There was a statistically significant difference in bond strength between group C and groups HF, SC and E (p < 0.001, p = 0.002 and p = 0.041, respectively). Posts of group SB and group N showed the highest surface roughness. Conclusions. The findings of the present study reveal that hydrofluoric acid-etching, silica coating and Er:YAG laser irradiation provided a significant increase in bond strength between glass fiber posts and resin cement.     

Er:YAG激光和酸蚀作用于牙釉质表面后剪切强度的比较研究

目的 探讨Er:YAG激光照射对牙釉质表面的蚀刻效果,并与酸蚀效果进行比较研究.方法 2010年4-7月在山西医科大学选取40颗完整的人离体双尖牙,随机分为4组(每组各10颗牙),即酸蚀组(35%的磷酸),Er:YAG激光组(5Hz,100 mJ,0.5W),酸蚀加Er:YAG激光组,Er:YAG激光加酸蚀组.分别在牙...