Three‐dimensional flow‐independent balanced steady‐state free precession vessel wall MRI of the popliteal artery: Preliminary experience and comparison with flow‐dependent black‐blood techniques

Purpose:

To examine the feasibility of flow‐independent T2‐prepared inversion recovery (T2IR) black‐blood (BB) magnetization preparation for three‐dimensional (3D) balanced steady‐state free precession (SSFP) vessel wall MRI of the popliteal artery, and to evaluate its performance relative to flow‐dependent double inversion recovery (DIR), spatial presaturation (SPSAT), and motion‐sensitizing magnetization preparation (MSPREP) BB techniques in healthy volunteers.

Materials and Methods:

Eleven subjects underwent 3D MRI at 1.5 Tesla with four techniques performed in a randomized order. Wall and lumen signal‐to‐noise ratio (SNR), wall‐to‐lumen contrast‐to‐noise ratio (CNR), vessel wall area, and lumen area were measured at proximal, middle, and distal locations of the imaged popliteal artery. Image quality scores based on wall visualization and degree of intraluminal artifacts were also obtained.

Results:

In the proximal region, DIR and SPSAT had higher wall SNR and wall‐to‐lumen CNR than both MSPREP and T2IR. In the middle and distal regions, DIR and SPSAT failed to provide effective blood suppression, whereas MSPREP and T2IR provided adequate black blood contrast with comparable wall‐to‐lumen CNR and image quality.

Conclusion:

The feasibility of 3D SSFP imaging of the popliteal vessel wall using flow‐independent T2IR was demonstrated with effective blood suppression and good vessel wall visualization. Although DIR and SPSAT are effective for thin slab imaging, MSPREP and T2IR are better suited for 3D thick slab imaging. J. Magn. Reson. Imaging 2011;. © 2011 Wiley‐Liss, Inc.     

3D flow‐independent peripheral vessel wall imaging using T2‐prepared phase‐sensitive inversion‐recovery steady‐state free precession

Purpose:

To develop a 3D flow‐independent peripheral vessel wall imaging method using T₂‐prepared phase‐sensitive inversion‐recovery (T₂PSIR) steady‐state free precession (SSFP).

Materials and Methods:

A 3D T₂‐prepared and nonselective inversion‐recovery SSFP sequence was designed to achieve flow‐independent blood suppression for vessel wall imaging based on T₁ and T₂ properties of the vessel wall and blood. To maximize image contrast and reduce its dependence on the inversion time (TI), phase‐sensitive reconstruction was used to restore the true signal difference between vessel wall and blood. The feasibility of this technique for peripheral artery wall imaging was tested in 13 healthy subjects. Image signal‐to‐noise ratio (SNR), wall/lumen contrast‐to‐noise ratio (CNR), and scan efficiency were compared between this technique and conventional 2D double inversion recovery – turbo spin echo (DIR‐TSE) in eight subjects.

Results:

3D T₂PSIR SSFP provided more efficient data acquisition (32 slices and 64 mm in 4 minutes, 7.5 seconds per slice) than 2D DIR‐TSE (2–3 minutes per slice). SNR of the vessel wall and CNR between vessel wall and lumen were significantly increased as compared to those of DIR‐TSE (P < 0.001). Vessel wall and lumen areas of the two techniques are strongly correlated (intraclass correlation coefficients: 0.975 and 0.937, respectively; P < 0.001 for both). The lumen area of T₂PSIR SSFP is slightly larger than that of DIR‐TSE (P = 0.008). The difference in vessel wall area between the two techniques is not statistically significant.

Conclusion:

T₂PSIR SSFP is a promising technique for peripheral vessel wall imaging. It provides excellent blood signal suppression and vessel wall/lumen contrast. It can cover a 3D volume efficiently and is flow‐ and TI‐independent. J. Magn. Reson. Imaging 2010;32:399–408. © 2010 Wiley‐Liss, Inc.     

Black-blood steady-state free precession (SSFP) coronary wall MRI for cardiac allografts: a feasibility study

Purpose:

To assess the hypothesis that steady‐state free procession (SSFP) allows for imaging of the coronary wall under the conditions of fast heart rate in heart transplantation (HTx) patients.

Materials and Methods:

With the approval of our Institutional Review Board, 28 HTx patients were scanned with a 1.5T scanner. Cross‐sectional black‐blood images of the proximal portions of the left main artery, left anterior descending artery, and right coronary artery were acquired with both a 2D, double inversion recovery (DIR) prepared turbo (fast) spin echo (TSE) sequence and a 2D DIR SSFP sequence. Image quality (scored 0–3), vessel wall area, thickness, signal‐to‐noise ratio (SNR, vessel wall), and contrast‐to‐noise ratio (CNR, wall‐lumen) were compared between TSE and SSFP.

Results:

The overall image quality of SSFP was higher than TSE (1.23 ± 0.95 vs. 0.88 ± 0.69, P < 0.001). SSFP had a higher coronary wall SNR (20.1 ± 8.5 vs. 14.9 ± 4.8, P < 0.001) and wall‐lumen CNR (8.2 ± 4.6 vs. 6.8 ± 3.7, P = 0.005) than TSE.

Conclusion:

Black‐blood SSFP coronary wall MRI provides higher image quality, SNR, and CNR than traditional TSE does in HTx recipients. It has the potential to become an alternative means to noninvasive imaging of cardiac allografts. J. Magn. Reson. Imaging 2012;35:1210‐1215. © 2012 Wiley Periodicals, Inc.     

High-resolution proton density weighted three-dimensional fast spin echo (3D-FSE) of the knee with IDEAL at 1.5 Tesla: comparison with 3D-FSE and 2D-FSE--initial experience

Purpose:

To assess the feasibility of combining three‐dimensional fast spin echo (3D‐FSE) and Iterative‐decomposition‐of water‐and‐fat‐with‐echo asymmetry‐and‐least‐squares‐estimation (IDEAL) at 1.5 Tesla (T), generating a high‐resolution 3D isotropic proton density‐weighted image set with and without “fat‐suppression” (FS) in a single acquisition, and to compare with 2D‐FSE and 3D‐FSE (without IDEAL).

Materials and Methods:

Ten asymptomatic volunteers prospectively underwent sagittal 3D‐FSE‐IDEAL, 3D‐FSE, and 2D‐FSE sequences at 1.5T (slice thickness [ST]: 0.8 mm, 0.8 mm, and 3.5 mm, respectively). 3D‐FSE and 2D‐FSE were repeated with frequency‐selective FS. Fluid, cartilage, and muscle signal‐to‐noise ratio (SNR) and fluid‐cartilage contrast‐to‐noise ratio (CNR) were compared among sequences. Three blinded reviewers independently scored quality of menisci/cartilage depiction for all sequences. “Fat‐suppression” was qualitatively scored and compared among sequences.

Results:

3D‐FSE‐IDEAL fluid‐cartilage CNR was higher than in 2D‐FSE (P < 0.05), not different from 3D‐FSE (P = 0.31). There was no significant difference in fluid SNR among sequences. 2D‐FSE cartilage SNR was higher than in 3D FSE‐IDEAL (P < 0.05), not different to 3D‐FSE (P = 0.059). 2D‐FSE muscle SNR was higher than in 3D‐FSE‐IDEAL (P < 0.05) and 3D‐FSE (P < 0.05). Good or excellent depiction of menisci/cartilage was achieved using 3D‐FSE‐IDEAL in the acquired sagittal and reformatted planes. Excellent, homogeneous “fat‐suppression” was achieved using 3D‐FSE‐IDEAL, superior to FS‐3D‐FSE and FS‐2D‐FSE (P < 0.05).

Conclusion:

3D FSE‐IDEAL is a feasible approach to acquire multiplanar images of diagnostic quality, both with and without homogeneous “fat‐suppression” from a single acquisition. J. Magn. Reson. Imaging 2012;361‐369. © 2011 Wiley Periodicals, Inc.     

Improved blood suppression in three‐dimensional (3D) fast spin‐echo (FSE) vessel wall imaging using a combination of double inversion‐recovery (DIR) and diffusion sensitizing gradient (DSG) preparations

Purpose:

To provide improved blood suppression in three‐dimensional inner‐volume fast spin‐echo (3D IV‐FSE) carotid vessel wall imaging by using a hybrid preparation consisting of double inversion‐recovery (DIR) and diffusion sensitizing gradients (DSG).

Materials and Methods:

Multicontrast black‐blood MRI is widely used for vessel wall imaging and characterization of atherosclerotic plaque composition. Blood suppression is difficult when using 3D volumetric imaging techniques. DIR approaches do not provide robust blood suppression due to incomplete replacement of blood spins, and DSG approaches compromise vessel wall signal, reducing the lumen‐wall contrast‐to‐noise ratio efficiency (CNR_eff). In this work a hybrid DIR+DSG preparation is developed and optimized for blood suppression, vessel wall signal preservation, and vessel‐wall contrast in 3D IV‐FSE imaging. Cardiac gated T₁‐weighted carotid vessel wall images were acquired in five volunteers with 0.5 × 0.5 × 2.5 mm³ spatial resolution in 80 seconds.

Results:

Data from healthy volunteers indicate that the proposed method yields a statistically significant (P < 0.01) improvement in blood suppression and lumen‐wall CNR_eff compared to standard DIR and standard DSG methods alone.

Conclusion:

A combination of DIR and DSG preparations can provide improved blood suppression and lumen‐wall CNR_eff for 3D IV‐FSE vessel wall imaging. J. Magn. Reson. Imaging 2010; 31: 398–405. © 2010 Wiley‐Liss, Inc.     

Cine cardiac imaging using black‐blood steady‐state free precession (BB‐SSFP) at 3T

Purpose

To propose a new black‐blood (BB) pulse sequence that provides BB cine cardiac images with high blood‐myocardium contrast. The proposed technique is based on the conventional steady‐state free precession (SSFP) sequence.

Materials and Methods

Numerical simulations of the Bloch equation were conducted to compare the resulting signal‐to‐noise ratio (SNR) to that of conventional BB imaging, including the effects of changing the imaging flip angle and heart rates. Simulation results were verified using a gel phantom experiment and five normal volunteers were scanned using the proposed technique.

Results

The new sequence showed higher SNR and contrast‐to‐noise ratio (CNR) (≈100%) compared to the conventional BB imaging. Also, the borders of the left ventricle (LV) and right ventricle (RV) appear more distinguishable than the conventional SSFP. We were also able to cover about 80% of the cardiac cycle with short breath‐hold time (≈10 cardiac cycles) and with reasonable SNR and CNR.

Conclusion

Based on an SSFP conventional sequence, the new sequence provides BB cines that cover most of the cardiac cycle and with higher SNR and CNR than the conventional BB sequences. J. Magn. Reson. Imaging 2009;30:94–103. © 2009 Wiley‐Liss, Inc.     

Enhanced image quality in black‐blood MRI using the improved motion‐sensitized driven‐equilibrium (iMSDE) sequence

Purpose

To propose an improved motion‐sensitized driven‐equilibrium (iMSDE) pulse sequence to enhance the tissue signal‐to‐noise ratio (SNR) while maintaining the same flow suppression capability in black‐blood carotid artery magnetic resonance imaging (MRI).

Materials and Methods

Compared to the traditional MSDE sequence, the iMSDE sequence uses an extra refocusing pulse and two extra gradients to achieve SNR improvement. Computer simulation and phantom studies were used to evaluate both eddy currents and local B₁ inhomogeneity effects on SNR behaviors on both MSDE and iMSDE images. To further assess the SNR improvements brought by iMSDE in vivo, five healthy volunteers were also scanned with both sequences. The paired t‐test was used for statistical comparison.

Results

Both simulations and phantom studies demonstrated that eddy currents and local B₁ inhomogeneity will cause image SNR reduction in the MSDE sequence, and that these factors can be partially compensated for with the iMSDE sequence. In vivo comparison showed that the iMSDE sequence significantly improved the tissue‐lumen contrast‐to‐noise ratio (CNR) and static tissue SNR (P < 0.001 for both), while maintaining low lumen SNR in carotid MRI.

Conclusion

Compared to the traditional MSDE sequence, the iMSDE sequence can achieve improved soft‐tissue SNR and CNR in carotid artery MRI without sacrificing flow suppression capability and time efficiency. J. Magn. Reson. Imaging 2010;31:1256–1263. © 2010 Wiley‐Liss, Inc.     

Flow‐independent T2‐prepared inversion recovery black‐blood MR imaging

Purpose:

To develop a magnetization preparation method to achieve robust, flow‐independent blood suppression for cardiac and vascular magnetic resonance imaging (MRI).

Materials and Methods:

T₂Prep‐IR sequence consists of a T₂ preparation followed by a nonselective adiabatic inversion pulse. T₂Prep separates the initial longitudinal magnetization of arterial wall from lumen blood. After the inversion recovery pulse the imaging acquisition is then delayed for a period that allows the blood signal to approach the zero‐crossing point. Compared to the conventional double inversion recovery (DIR) preparation, T₂Prep‐IR prepares all the spins regardless of their velocity and direction. T₂Prep‐IR was incorporated into the fast spin echo and fast gradient echo acquisition sequences and images in various planes were acquired in the carotid arteries, thoracic aorta, and heart of normal volunteers. Blood suppression and image quality were compared qualitatively between two different preparations.

Results:

For in‐plane flow carotid images, persistent flow‐related artifacts on the DIR images were removed with T₂Prep‐IR. For cardiac applications, T₂Prep‐IR provided robust blood suppression regardless of the flow direction and velocity, including the cardiac long‐axis views and the aorta that are often problematic with DIR.

Conclusion:

T₂Prep‐IR may overcome the flow dependence of DIR by providing robust flow‐independent black‐blood images. J. Magn. Reson. Imaging 2010;31:248–254. © 2009 Wiley‐Liss, Inc     

Pilot study of improved lesion characterization in breast MRI using a 3D radial balanced SSFP technique with isotropic resolution and efficient fat‐water separation

Purpose

To assess a 3D radial balanced steady‐state free precession (SSFP) technique that provides submillimeter isotropic resolution and inherently registered fat and water image volumes in comparison to conventional T2‐weighted RARE imaging for lesion characterization in breast magnetic resonance imaging (MRI).

Materials and Methods

3D projection SSFP (3DPR‐SSFP) combines a dual half‐echo radial k‐space trajectory with a linear combination fat/water separation technique (linear combination SSFP). A pilot study was performed in 20 patients to assess fat suppression and depiction of lesion morphology using 3DPR‐SSFP. For all patients fat suppression was measured for the 3DPR‐SSFP image volumes and depiction of lesion morphology was compared against corresponding T2‐weighted fast spin echo (FSE) datasets for 15 lesions in 11 patients.

Results

The isotropic 0.63 mm resolution of the 3DPR‐SSFP sequence demonstrated improved depiction of lesion morphology in comparison to FSE. The 3DPR‐SSFP fat and water datasets were available in a 5‐minute scan time while average fat suppression with 3DPR‐SSFP was 71% across all 20 patients.

Conclusion

3DPR‐SSFP has the potential to improve the lesion characterization information available in breast MRI, particularly in comparison to conventional FSE. A larger study is warranted to quantify the effect of 3DPR‐SSFP on specificity. J. Magn. Reson. Imaging 2009;30:135–144. © 2009 Wiley‐Liss, Inc.     

Non‐contrast‐enhanced MR angiography for selective visualization of the hepatic vein and inferior vena cava with true steady‐state free‐precession sequence and time‐spatial labeling inversion pulses: Preliminary results

Purpose

To selectively visualize the hepatic vein and inferior vena cava (IVC) using three‐dimensional (3D) true steady‐state free‐precession (SSFP) MR angiography with time‐spatial labeling inversion pulse (T‐SLIP), and to optimize the acquisition protocol.

Materials and Methods

Respiratory‐gated 3D true SSFP scans were conducted in 23 subjects in combination with two different T‐SLIPs (one placed in the thorax to suppress the arterial signal and the other in the abdomen to suppress the portal venous signal). One of the most important factors was the inversion time (TI) of abdominal T‐SLIP, and the image quality was evaluated at four different TIs of 800, 1200, 1600, and 2000 msec in terms of relative signal‐to‐noise ratio (SNR), contrast‐to‐noise ratio (CNR), and mean visualization scores.

Results

No significant difference was observed in SNR and CNR between each TI. However, IVC visualization scores were better at TIs of 1600 and 2000 msec, and overall image quality was better at TIs of 1200 and 1600 msec. Therefore, the TI of 1600 msec was considered to provide the optimal balance between IVC visualization and signal suppression of the portal vein in our protocol.

Conclusion

True SSFP scan with T‐SLIPs enabled selective visualization of the hepatic vein and IVC without an exogenous contrast agent. J. Magn. Reson. Imaging 2009;29:474–479. © 2009 Wiley‐Liss, Inc.     

Non‐contrast‐enhanced MR portography with time‐spatial labeling inversion pulses: Comparison of imaging with three‐dimensional half‐fourier fast spin‐echo and true steady‐state free‐precession sequences

Purpose

To compare and evaluate images acquired with two different MR angiography (MRA) sequences, three‐dimensional (3D) half‐Fourier fast spin‐echo (FSE) and 3D true steady‐state free‐precession (SSFP) combined with two time‐spatial labeling inversion pulses (T‐SLIPs), for selective and non‐contrast‐enhanced (non‐CE) visualization of the portal vein.

Materials and Methods

Twenty healthy volunteers were examined using half‐Fourier FSE and true SSFP sequences on a 1.5T MRI system with two T‐SLIPs, one placed on the liver and thorax, and the other on the lower abdomen. For quantitative analysis, vessel‐to‐liver contrast (Cv‐l) ratios of the main portal vein (MPV), right portal vein (RPV), and left portal vein (LPV) were measured. The quality of visualization was also evaluated.

Results

In both pulse sequences, selective visualization of the portal vein was successfully conducted in all 20 volunteers. Quantitative evaluation showed significantly better Cv‐l at the RPVs and LPVs in half‐Fourier FSE (P < 0.0001). At the MPV, Cv‐l was better in true SSFP, but was not statistically different. Visualization scores were significantly better only at branches of segments four and eight for half‐Fourier FSE (P = 0.001 and 0.03, respectively).

Conclusion

Both 3D half‐Fourier FSE and true SSFP scans with T‐SLIPs enabled selective non‐CE visualization of the portal vein. Half‐Fourier FSE was considered appropriate for intrahepatic portal vein visualization, and true SSFP may be preferable when visualization of the MPV is required. J. Magn. Reson. Imaging 2009;29:1140–1146. © 2009 Wiley‐Liss, Inc.     

Cartilage morphology at 3.0T: Assessment of three‐dimensional magnetic resonance imaging techniques

Purpose:

To compare six new three‐dimensional (3D) magnetic resonance (MR) methods for evaluating knee cartilage at 3.0T.

Materials and Methods:

We compared: fast‐spin‐echo cube (FSE‐Cube), vastly undersampled isotropic projection reconstruction balanced steady‐state free precession (VIPR‐bSSFP), iterative decomposition of water and fat with echo asymmetry and least‐squares estimation combined with spoiled gradient echo (IDEAL‐SPGR) and gradient echo (IDEAL‐GRASS), multiecho in steady‐state acquisition (MENSA), and coherent oscillatory state acquisition for manipulation of image contrast (COSMIC). Five‐minute sequences were performed twice on 10 healthy volunteers and once on five osteoarthritis (OA) patients. Signal‐to‐noise ratio (SNR) and contrast‐to‐noise ratio (CNR) were measured from the volunteers. Images of the five volunteers and the five OA patients were ranked on tissue contrast, articular surface clarity, reformat quality, and lesion conspicuity. FSE‐Cube and VIPR‐bSSFP were compared to IDEAL‐SPGR for cartilage volume measurements.

Results:

FSE‐Cube had top rankings for lesion conspicuity, overall SNR, and CNR (P < 0.02). VIPR‐bSSFP had top rankings in tissue contrast and articular surface clarity. VIPR and FSE‐Cube tied for best in reformatting ability. FSE‐Cube and VIPR‐bSSFP compared favorably to IDEAL‐SPGR in accuracy and precision of cartilage volume measurements.

Conclusion:

FSE‐Cube and VIPR‐bSSFP produce high image quality with accurate volume measurement of knee cartilage. J. Magn. Reson. Imaging 2010;32:173–183. © 2010 Wiley‐Liss, Inc.     

MRI of the wrist at 7 tesla using an eight‐channel array coil combined with parallel imaging: Preliminary results

Purpose:

To determine the feasibility of performing MRI of the wrist at 7 Tesla (T) with parallel imaging and to evaluate how acceleration factors (AF) affect signal‐to‐noise ratio (SNR), contrast‐to‐noise ratio (CNR), and image quality.

Materials and Methods:

This study had institutional review board approval. A four‐transmit eight‐receive channel array coil was constructed in‐house. Nine healthy subjects were scanned on a 7T whole‐body MR scanner. Coronal and axial images of cartilage and trabecular bone micro‐architecture (3D‐Fast Low Angle Shot (FLASH) with and without fat suppression, repetition time/echo time = 20 ms/4.5 ms, flip angle = 10°, 0.169–0.195 × 0.169–0.195 mm, 0.5–1 mm slice thickness) were obtained with AF 1, 2, 3, 4. T1‐weighted fast spin‐echo (FSE), proton density‐weighted FSE, and multiple‐echo data image combination (MEDIC) sequences were also performed. SNR and CNR were measured. Three musculoskeletal radiologists rated image quality. Linear correlation analysis and paired t‐tests were performed.

Results:

At higher AF, SNR and CNR decreased linearly for cartilage, muscle, and trabecular bone (r < ?0.98). At AF 4, reductions in SNR/CNR were:52%/60% (cartilage), 72%/63% (muscle), 45%/50% (trabecular bone). Radiologists scored images with AF 1 and 2 as near‐excellent, AF 3 as good‐to‐excellent (P = 0.075), and AF 4 as average‐to‐good (P = 0.11).

Conclusion:

It is feasible to perform high resolution 7T MRI of the wrist with parallel imaging. SNR and CNR decrease with higher AF, but image quality remains above‐average. J. Magn. Reson. Imaging 2010;31:740–746. © 2010 Wiley‐Liss, Inc.

     

Improvements in carotid plaque imaging using a new eight‐element phased array coil at 3T

Purpose

To design and compare an eight‐channel phased array (PA) coil for carotid imaging to an established four‐channel PA design at 3T.

Materials and Methods

An eight‐channel PA (8PA) coil was designed specifically for imaging the carotid bifurcation and compared with the existing four‐channel (4PA) design using a phantom and by in vivo black‐blood magnetic resonance imaging (MRI). The 8PA and 4PA were compared in terms of coverage, signal‐to‐noise ratio (SNR), and contrast‐to‐noise ratio (CNR).

Results

The 8PA showed up to 1.7‐fold improvement in SNR at a depth of 3.5 cm and greater longitudinal coverage at a given SNR on a phantom. The 8PA showed improved vessel wall SNR for high spatial resolution (0.63 mm²) PD, T1, and T2 (1.7, 1.7, 1.6 times, respectively; P ≤ 0.002) and improved CNR (1.7, 1.6, 1.5 times, respectively; P ≤ 0.002). Ultrahigh‐resolution (0.27 mm²) T1‐weighted images showed better SNR and CNR (1.4 times, P ≤ 0.0001) on 8PA compared to 4PA.

Conclusion

Carotid imaging studies may benefit from the improved SNR and larger coverage provided by use of the 8PA. J. Magn. Reson. Imaging 2009. © 2009 Wiley‐Liss, Inc.     

Imaging of the wrist at 1.5 Tesla using isotropic three-dimensional fast spin echo cube

Purpose:

To compare three‐dimensional fast spin echo Cube (3D‐FSE‐Cube) with conventional 2D‐FSE in MR imaging of the wrist.

Materials and Methods:

The wrists of 10 volunteers were imaged in a 1.5 Tesla MRI scanner using an eight‐channel wrist coil. The 3D‐FSE‐Cube images were acquired in the coronal plane with 0.5‐mm isotropic resolution. The 2D‐FSE images were acquired in both coronal and axial planes for comparison. An ROI was placed in fluid, cartilage, and muscle for SNR analysis. Comparable coronal and axial images were selected for each sequence, and paired images were randomized and graded for blurring, artifact, anatomic details, and overall image quality by three blinded musculoskeletal radiologists.

Results:

SNR of fluid, cartilage and muscle at prescribed locations were higher using 3D‐FSE‐Cube, without reaching statistical significance. Fluid–cartilage CNR was also higher with 3D‐FSE‐Cube, but not statistically significant. Blurring, artifact, anatomic details, and overall image quality were significantly better on coronal 3D‐FSE‐Cube images (P < 0.001), but significantly better on axial 2D‐FSE images compared with axial 3D‐FSE‐Cube reformats (P < 0.01).

Conclusion:

Isotropic data from 3D‐FSE‐Cube allows reformations in arbitrary scan planes, which may make multiple 2D acquisitions unnecessary, and improve depiction of complex wrist anatomy. However, axial reformations suffer from blurring, likely due to T2 decay during the long echo train, limiting overall image quality in this plane. J. Magn. Reson. Imaging 2011;33:908–915. © 2011 Wiley‐Liss, Inc.     

Inflow quantification in three-dimensional cardiovascular MR imaging

Purpose

To investigate blood inflow enhancement (or lack thereof) in three‐dimensional (3D) cardiovascular MR for both single phase whole‐heart and cine biventricular functions.

Materials and Methods

A 3D imaging sequence is proposed in which radiofrequency excitation gradient is changed without modifying image acquisition or phase/slice encoding. This imaging sequence enables direct inflow measurement while retaining static voxel signal‐to‐noise ratio. Inflow measurements were performed for both spoiled gradient‐echo (GRE) imaging and balanced steady‐state free precession (SSFP) in 18 healthy subjects.

Results

For single phase imaging, increasing slab thickness from 3 to 10 cm lead to 73% and 59% reductions in contrast‐to‐noise ratio (CNR) with GRE and SSFP, respectively. For cine acquisitions, systolic CNR was reduced by 85% and 50% for the GRE and SSFP acquisitions, respectively, while diastolic CNR was reduced by 64% and 42%.

Conclusion

There is significant loss of CNR between blood and myocardium when using larger 3D slabs due to saturation of inflowing spins. The loss of contrast is less pronounced for SSFP than for GRE, though both acquisition techniques suffer. J. Magn. Reson. Imaging 2008;28:1273–1279. © 2008 Wiley‐Liss, Inc.     

Aortic vessel wall magnetic resonance imaging at 3.0 Tesla: A reproducibility study of respiratory navigator gated free‐breathing 3D black blood magnetic resonance imaging

The purpose of this study was to evaluate a free‐breathing three‐dimensional (3D) dual inversion‐recovery (DIR) segmented k‐space gradient‐echo (turbo field echo [TFE]) imaging sequence at 3T for the quantification of aortic vessel wall dimensions. The effect of respiratory motion suppression on image quality was tested. Furthermore, the reproducibility of the aortic vessel wall measurements was investigated. Seven healthy subjects underwent 3D DIR TFE imaging of the aortic vessel wall with and without respiratory navigator. Subsequently, this sequence with respiratory navigator was performed twice in 10 healthy subjects to test its reproducibility. The signal‐to‐noise (SNR), contrast‐to‐noise ratio (CNR), vessel wall sharpness, and vessel wall volume (VWV) were assessed. Data were compared using the paired t‐test, and the reproducibility of VWV measurements was evaluated using intraclass correlation coefficients (ICCs). SNR, CNR, and vessel wall sharpness were superior in scans performed with respiratory navigator compared to scans performed without. The ICCs concerning intraobserver, interobserver, and interscan reproducibility were excellent (0.99, 0.94, and 0.95, respectively). In conclusion, respiratory motion suppression substantially improves image quality of 3D DIR TFE imaging of the aortic vessel wall at 3T. Furthermore, this optimized technique with respiratory motion suppression enables assessment of aortic vessel wall dimensions with high reproducibility. Magn Reson Med 61:35–44, 2009. © 2008 Wiley‐Liss, Inc.     

On the use of a spin-echo based double inversion recovery acquisition for the measurement of cortical brain thickness

Purpose:

To determine whether a spin‐echo‐based sequence, which are inherently insensitive to magnetic field inhomogeneity, can be used for brain cortical thickness measurement studies.

Materials and Methods:

By using a double inversion recovery (DIR) spin‐echo‐based sequence, cortical thickness estimates were performed from data acquired from seven healthy volunteers. The cortical thickness was also calculated from data acquired using an MPRAGE sequence and the Bland‐Altman analysis was performed for comparison of the two methods. The average signal and contrast to noise ratios (SNR, CNR) of the two methods were also calculated.

Results:

The bias over the entire brain between DIR and MPRAGE was 0.87 ± 0.08 mm. The bias calculated in the major regional lobes were temporal: 0.76 ± 0.09 mm, frontal: 0.89 ± 0.07 mm, parietal: 0.92 ± 0.10 mm, occipital: 0.75 ± 0.12 mm, and cingulate: 0.79 ± 0.10 mm. This thickness difference was due mainly to the boundary difference in the MPRAGE and DIR at the grey matter/cerebral spinal fluid (GM/CSF) regions. The mean SNR and CNR was CNR_MPRAGE = 47.8 ± 8.4 and CNR_DIR = 19.2 ± 2.9, SNR_MPRAGE = 76.8 ± 10.5 and SNR_DIR = 21.1 ± 2.8.

Conclusion:

The study suggests that cortical thickness measurements can be performed using a DIR spin‐echo sequence, which is inherently immune to main field inhomogeneity. Larger thickness measurements were consistently observed in DIR compared with MPRAGE. J. Magn. Reson. Imaging 2011;33:1218–1223. © 2011 Wiley‐Liss, Inc.     

Fast three‐dimensional dual echo dixon technique improves fat suppression in breast MRI

Purpose:

To compare qualitative and quantitative measures of the contrast‐enhanced dual‐echo Dixon technique with the commonly used standard three‐dimensional (3D) gradient echo (spectrally selective fat suppression) technique (SS‐FS) in breast MRI exams (bMRI).

Materials and Methods:

A total of 19 women, with prescheduled bMRI exam, were recruited to our study between 2006 and 2008. Dixon and standard SS‐SF techniques were used on both breasts of each patient. Image quality was rated in five categories: fat suppression quality, fat suppression uniformity, lesion margin clarity, lesion visibility, and axillary visibility. For quantitative assessment, we calculated the signal‐to‐noise ratio (SNR) and contrast‐to‐noise ratio (CNR) of lesion to breast, SNR efficiency, and CNR efficiency.

Results:

Of 19 patients evaluated, 13 had a primary breast malignancy and 6 had benign lesions or negative exams. Dixon images were rated higher in four of five qualitative categories (P < 0.0001) and required a shorter scan time. Dixon images yielded significantly higher SNR (43.8) and CNR (40.1) values than did 3DGRE images (SNR = 34.8, CNR = 25.3; P < 0.05). SNR efficiency (36.30) and CNR efficiency (33.79) values for Dixon images were also higher than were 3DGRE images (SNR efficiency =25.7, CNR efficiency = 19.1; P < 0.05).

Conclusion:

Dixon images were superior to the standard SS‐SF images in both qualitative and quantitative assessment of 19 bMRI exams. The Dixon technique could replace standard SS‐SF technique in bMRI exam, after our findings have been confirmed in future studies with a larger sample size. J. Magn. Reson. Imaging 2010;31:889–894. ©2010 Wiley‐Liss, Inc.     

3D velocity quantification in the heart: Improvements by 3D PC‐SSFP

Purpose:

To test whether a 3D imaging sequence with phase contrast (PC) velocity encoding based on steady‐state free precession (SSFP) improves 3D velocity quantification in the heart compared to the currently available gradient echo (GE) approach.

Materials and Methods:

The 3D PC‐SSFP sequence with 1D velocity encoding was compared at the mitral valve in 12 healthy subjects with 3D PC‐GE at 1.5T. Velocity measurements, velocity‐to‐noise‐ratio efficiency (VNR_eff), intra‐ and interobserver variability of area and velocity measurements, contrast‐to‐noise‐ratio (CNR), and artifact sensitivity were evaluated in both long‐ and short‐axis orientation.

Results:

Descending aorta mean and peak velocities correlated well (r² = 0.79 and 0.93) between 3D PC‐SSFP and 3D PC‐GE. At the mitral valve, mean velocity correlation was moderate (r² = 0.70 short axis, 0.56 long axis) and peak velocity showed good correlation (r² = 0.94 short axis, 0.81 long axis). In some cases VNR_eff was higher, in others lesser, depending on slab orientation and cardiac phase. Intra‐ and interobserver variability was generally better for 3D PC‐SSFP. CNR improved significantly, especially at end systole. Artifact levels did not increase.

Conclusion:

3D SSFP velocity quantification was successfully tested in the heart. Blood‐myocardium contrast improved significantly, resulting in more reproducible velocity measurements for 3D PC‐SSFP at 1.5T. J. Magn. Reson. Imaging 2009;30:947–955. © 2009 Wiley‐Liss, Inc.