马来酸罗格列酮固体分散体及其溶出速率

目的提高难溶性药物马来酸罗格列酮的体外溶出速率 ,满足脉冲制剂的设计要求。方法选用PVPK3 0为载体 ,用溶剂法制备了马来酸罗格列酮固体分散体 ,比较考察了原料药及其物理混合物和固体分散体的溶出差别 ,并通过红外光谱及X 射线粉末衍射对固体分散体进行了鉴定。结果体外溶出结果表明固体分散体能显著增加药物在水中及人工肠液中的溶出速率 ;红外光谱分析结果表明药物与载体之间没有发生化学反应 ;X 射线粉末衍射图谱表明药物以无定形状态分散于载体PVPK3 0中。结论固体分散体体外溶出速率的提高可以满足脉冲制剂的设计要求。     

Development and in-vivo assessment of the bioavailability of oridonin solid dispersions by the gas anti-solvent technique

We developed solid dispersions, using the gas anti-solvent technique (GAS), to improve the oral bioavailability of the poorly water-soluble active component oridonin. The solubility of oridonin in supercritical carbon dioxide was measured under various pressures and temperatures. To prepare oridonin solid dispersions using the GAS technique, ethanol was used as the solvent, CO(2) was used as the anti-solvent and the hydrophilic polymer polyvinylpyrrolidone K17 (PVP K17) was used as the drug carrier matrix. Characterization of the obtained preparations was undertaken using scanning electron microscopy (SEM), X-ray diffraction (XRD) analyses and a drug release study. Oridonin solid dispersions were formed and oridonin was present in an amorphous form in these dispersions. Oridonin solid dispersions significantly increased the drug dissolution rate compared with that of oridonin powder, primarily through drug amorphization. Compared with the physical mixture of oridonin and PVP K17, oridonin solid dispersions gave higher values of AUC and C(max), and the absorption of oridonin from solid dispersions resulted in 26.4-fold improvement in bioavailability. The present study illustrated the feasibility of applying the GAS technique to prepare oridonin solid dispersions, and of using them for the delivery of oridonin via the oral route.     

Solid state properties of pure UC-781 and solid dispersions with polyvinylpyrrolidone (PVP K30)

The purpose of this study was to elucidate the physical structure of solid dispersions of the antiviral agent UC-781 (N-[4-chloro-3-(3-methyl-2-butenyloxy)phenyl]-2-methyl-3-furancarbothioamide) with polyvinylpyrrolidone (PVP K30). Solid dispersions were prepared by coevaporating UC-781 with PVP K30 from dichloromethane. The physicochemical properties of the dispersions were evaluated in comparison with the physical mixtures by differential scanning calorimetry (DSC), X-ray powder diffraction, and FT-IR spectroscopy. We investigated the single crystal structure of pure UC-781. The data from single crystal analysis showed that UC-781 crystallized with orthorhombic symmetry in the space group Pcab. Its cell parameters were found to be; a = 8.1556(7) A,b = 17.658(2) A and c = 23.609(2) A; the unit cell was made up of eight molecules of UC-781. The molecules formed intermolecular hydrogen bonds between NH and thio groups, and were packed in a herringbone-like structure. The data from X-ray powder diffraction showed that crystalline UC-781 was changed into the amorphous state by co-evaporating it with PVP K30. From differential scanning calorimetry analysis, UC-781 peaks were observed in the DSC curves of all physical mixtures, while no peaks corresponding to the drug could be observed in the solid dispersions with the same drug composition up to the concentration of 50% w/w. The data from FT-IR spectroscopy showed the distortions and disappearance of some bands from the drug, while other bands were too broad or significantly less intense compared with the physical mixtures of the crystalline drug in PVP K30. Furthermore, the results from IR spectroscopy demonstrated that UC-781 interacted with PVP K30 in solid dispersions through intermolecular H-bonding.     

Dissolution behaviour of nalidixic acid solid dispersions using water soluble dispersion carriers

The oral bioavailability of nalidixic acid (NA) is low due to its poor solubility and slow dissolution. Solid dispersions of NA containing varying concentrations of polyvinylpyrrolidone (PVP), beta-cyclodextrin (BCD) and sodium starch glycolate (SSG) were prepared by solvent evaporation technique in an attempt to improve dissolution rate of NA. Physical characterization of NA, physical mixtures (PM) and solid dispersions were investigated by a variety of analytical methods including scanning electron microscopy (SEM), infrared (IR) spectroscopy and powder X-ray diffraction (XRD). SEM was useful in the verification of possible nalidixic acid inclusion in the dispersion system by studying its surface and shape characteristics of different samples. IR analysis demonstrated no strong interaction between the drug and the carrier exists in the solid dispersions. The degree of crystallinity of nalidixic acid decreased and also differed with the dispersion systems of different carriers. Disolution studies indicated that the dissolution rate and percent dissolution efficiency (DE) were significantly increased in the solid dispersions compared with drug alone. The relative potency of the carriers to enhance the dissolution rate of nalidixic acid was in the order: BCD > PVP > SSG. The dissolution rate of the drug in the solid dispersions was faster when the ration of the drug to carrier was smaller. F-test suggests that first order model may be used for explaining the kinetics of drug release from all the solid dispersion systems.     

Studies on Flash Evaporation for Preparation of Porous Solid Dispersions Using Piroxicam as a Model Drug

An amalgamation of solid dispersion and capillarity has been attempted in present study for enhancement of dissolution rate of poorly soluble drugs. Flash evaporation technique was utilized for enhancement of the dissolution rate of piroxicam. One of the major problems with this drug is its very low solubility in biological fluids, which results in poor bioavailability after oral administration. An attempt was made to enhance the dissolution rate of piroxicam by converting it into porous solid dispersion by flash evaporation method using polyvinylpyrrolidone (PVP) 40,000 as a water-soluble carrier. The resulting solid dispersions were characterized by DSC, FTIR, and X-ray diffraction. In vitro dissolution study revealed significant improvement of dissolution profile of piroxicam. The release of drug from porous solid dispersions containing PVP was superior to those of marketed product, conventional nonporous solid dispersion prepared by solvent evaporation method and drug alone. The steep increase in dissolution rate of porous form is attributable to combined effect of solid dispersion and capillarity.     

Poly(2-Ethyl-2-Oxazoline) as an Alternative to Poly(Vinylpyrrolidone) in Solid Dispersions for Solubility and Dissolution Rate Enhancement of Drugs

Poly(2-ethyl-2-oxazoline) (PEOX), a biocompatible polymer considered as pseudopolypeptide, was introduced as a potential alternative to the commonly used polymer, poly(vinylpyrrolidone) (PVP) for the preparation of solid dispersion with a poorly soluble drug. Glipizide (GPZ), a Biopharmaceutical Classification System class II model drug, was selected for solubility and dissolution rate study. GPZ-polymer solid dispersions and physical mixtures were characterized and investigated by X-ray diffractometry, differential scanning calorimetry, scanning electron microscopy, and FTIR spectroscopy. The impact of polymers on crystal nucleation kinetics was studied, and PEOX exhibited strong inhibitory effect compared with PVP. Solubility and dissolution behavior of the prepared solid dispersions and their physical blends were in vitro examined and evaluated. A significant enhancement in GPZ solubility was obtained with PEOX compared with the pure drug and solid dispersion with PVP. A big improvement in the intrinsic dissolution rate (45 times) and dissolved amount of GPZ (58 times) was achieved with PEOX in fasted state simulated intestinal fluid, against comparable enhancement observed with PEOX and PVP in phosphate buffer at pH 6.8. Lower molecular weight of PEOX-5K (5000 g/mol) was found to be superior to higher molecular weight PEOX-50K (50,000 g/mol) in the improvement of dissolution behavior. The findings of this study with GPZ as a model drug introduce lower molecular weight PEOX as a promising polymeric carrier toward better oral bioavailability of poorly soluble drugs.     

酮洛芬-聚乙烯吡咯烷酮固体分散物的制备及其体外溶出度的研究

目的提高难溶性药物酮洛芬体外溶出速度。方法以聚乙烯吡咯烷酮(PVPK30)为载体,制备药物与载体不同比例的固体分散物及物理混合物,采用X射线衍射和红外吸收方法,比较二者及药物的结晶形态,并进行体外药物溶出度的测定。结果固体分散物体外溶出速率明显高于物理混合物及酮洛芬原料的体外溶出速度,且随载体比例增加而增大。固体分散物的X射线衍射及红外吸收图谱确定了酮洛芬以无定形态分散在载体中,放置6个月后,固体分散物X射线衍射图谱没有明显变化。结论药物与载体以合适比例制备的固体分散物可以明显提高药物体外溶出速度。     

托伐普坦固体分散体的制备及体外溶出特性考察

目的 采用固体分散技术提高难溶性药物托伐普坦的体外溶出度。方法 选用聚维酮K_29/32为载体材料,以溶剂蒸发法制备托伐普坦固体分散体。采用差示扫描量热法(DSC)、X-射线粉末衍射法(XRPD)对所得固体分散体进行鉴定, 并进行溶解度、体外溶出实验。结果 固体分散体的DSC 图谱及X-射线粉末衍射确定了托伐普坦以无定形态分散在载体中, 体外溶解实验表明其溶出较原料药、物理混合物均有明显提高。结论 将托伐普坦与PVP K_29/32制成固体分散体,其分散状态发生了改变,溶出性能明显提高。     

Interactions of Poly(vinylpyrrolidone) with Ibuprofen and Naproxen: Experimental and Modeling Studies

Purpose. To elucidate the differences in the interaction of chiralic ibuprofen (IBP) and naproxen (NAP) with poly(vinylpyrrolidone) (PVP) in a solid state.Methods. Drugs/PVP physical mixtures and solid dispersions were characterized by scanning electron microscope (SEM), Fourier transform infrared spectrometry (FT-IR), solid state ¹³C NMR spectroscopy, and x-ray diffractometry. Molecular modeling study of the crystal structures and PVP was performed.Results. A spontaneous conversion of IBP/PVP physical mixtures in a stable glasslike form (solid dispersion) was observed after storage. The enantiomer reacted more strongly than the racemate. NAP did not interact with PVP. The crystal structures of drugs showed differences in the hydrogen bonding, aromatic interactions, molecular energies, and distances inside the crystals. The trimer structure of PVP was built and optimized. It was proposed that each PVP monomer could interact with one IBP dimmer in contrast to NAP, where two out of three PVP monomers faced the catemer carboxylic groups.Conclusions. The differences in the interaction of PVP with racemic IBP, enantiomer IBP, and NAP can be related to the differences in their crystal structures. The correlation between the experimental data and the results of the molecular modeling analysis suggest that the IBP dimmer structures are likely to perform HB and aromatic interactions with PVP.     

卡维地洛固体分散体的初步研制

目的:制备卡维地洛固体分散体并考察其体外溶出度。方法:以聚乙二醇(PEG)、聚乙烯吡咯烷酮(PVP)的混合物(2∶1、1∶2)为载体,采用溶剂熔融法和共沉淀法制备载体与药物不同比例的固体分散体并比较其体外溶出度。结果:药物溶出度随载体比例增加而增加;载体与药物比例越小,固体分散体与药物原料粉之间溶出度差异越显著;PEG∶PVP(1∶2)所制分散体体外溶出行为较优,以3、10、30、60min时溶出百分率进行比较,固体分散体是药物原料粉的3～8倍。结论:所制卡维地洛固体分散体能增加药物体外溶出度。     

Properties of solid dispersions of piroxicam in polyvinylpyrrolidone.

Solid dispersions of piroxicam were prepared with polyvinylpyrrolidone (PVP) K-17 PF and PVP K-90 by solvent method. The physical state and drug:PVP interaction of solid dispersions and physical mixtures were characterized by X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC). FTIR analysis demonstrated the presence of intermolecular hydrogen bonding between piroxicam and PVP in solid dispersions. These interactions reflected the changes in crystalline structures of piroxicam. The amorphousness within the PVP moeity might be predicted in piroxicam dispersions by the disappearance of N-H or O-H peak of piroxicam. Dissolution studies indicated a significant increase in dissolution of piroxicam when dispersed in PVP. The better results were obtained with the lower molecular weight PVP K-17 than with higher molecular weight PVP K-90. The non-amorphous solid dispersions in PVP K-17 showed almost equally fast dissolution rates to amorphous dispersions in PVP K-90. The mechanism of dissolution of solid dispersion in PVP K-90 is predominantly diffusion-controlled due to the very high viscosity of PVP K-90. Dissolution was maximum with the amorphous solid dispersions containing drug:PVP K-17 1:5 and 1:6 which showed a 40-fold increase in dissolution in 5 min as compared with pure drug. Copyright     

尼莫地平固体分散物的研究

尼莫地平临床上主要用于防治缺血性脑血管疾病．该药为难溶性药物，生物利用度低，本文采用了固体分散技术制备了尼莫地平两种固体分散物，其体外溶出速率１０分钟以内达８０％以上，较市售片有显著提高．两种固体分散物中，固体分散物Ⅰ为本实验室研制，固体分散物Ⅱ参照国内、外文献用ＰＶＰ为载体制备．两种固体分散物均能明显提高尼莫地平的体外溶出速率，但固体分散物Ⅱ易于老化，经相对湿度ＲＨ７５％４０℃贮藏３个月溶出速率明显下降，同样条件下，固体分散物Ⅰ则无明显变化．二种固体分散物Ｘ－射线衍射图谱表明尼莫地平以非晶体状态存在，而在ＲＨ７５％４０℃条件下放置３个月后，固体分散物ⅡＸ－射线衍射图谱出现了尼莫地平结晶峰．     

Investigation of atypical dissolution behavior of an encapsulated amorphous solid dispersion

Poor dissolution performance is one of the challenges encountered in dosage form design of amorphous solid dispersions (ASDs). This study was aimed to investigate the effect of solid-liquid interactions of an encapsulated ASD on drug release. Drug release profiles of a molecularly interacting amorphous celecoxib solid dispersion (ACSD) comprising of amorphous celecoxib (A-CLB), polyvinylpyrrolidone (PVP), and meglumine (7:2:1, w/w) were compared with crystalline CLB (C-CLB), in powder and capsule form. Although, ACSD powder displayed 28- to 50-fold higher dissolution efficiency at 60 min (DE(60)), the DE(60) in the encapsulated state were drastically reduced due to the formation of a nondispersible plug. The accompanied physical and compositional changes were investigated using X-ray powder diffraction, differential scanning calorimetry, scanning electron microscopy, and chromatographic techniques. ACSD displayed optimal wettability, sustained A-CLB-PVP interactions, and suppressed phase transformations in aqueous media. Furthermore, Fourier transform infrared and texture analysis revealed role of intermolecular interactions of the solid dispersion, which (i) altered PVP's functionality and (ii) promoted interparticle cohesivity via water-mediated hydrogen bonds, resulting in solid mass agglomeration. Parallel evaluation of A-CLB, physical mixture of ACSD components, and C-CLB solid dispersion supported the above inferences. On the basis of these findings, rationalized formulation approaches for ASD-based drug products are discussed.     

Enhancing the bioavailability of ABT-963 using solid dispersion containing Pluronic F-68

Solid dispersions using Pluronic F-68 as a carrier were studied for improving the dissolution and bioavailability of ABT-963, a poorly water-soluble compound. The solid dispersions were prepared either by evaporation of the ethanol solutions containing ABT-963 and Pluronic, or by cooling the hot melt of the drug in the carrier. The dispersions were characterized using differential scanning calorimetry, powder X-ray diffractometry, scanning electron microscopy, elemental mapping, and by constructing the melting point phase diagram. In vitro dissolution and in vivo oral bioavailability in fasted dogs were compared for the solid dispersion and a conventional IR capsule formulation. Results showed that, at a composition of approximately 7.5%, ABT-963 formed a eutectic mixture with Pluronic F-68. Both the drug and the polymer were crystalline in the solid dispersion with a wide range of composition of each component. The solid dispersion substantially increased the in vitro dissolution rate of ABT-963. Dosing of the dispersion to fasted dogs resulted in a significant increase of oral bioavailability compared with the conventional IR capsule formulation. These results show that solid dispersion is a promising approach for developing ABT-963 drug products.     

Anomalous properties of spray dried solid dispersions

The use of solid dispersions for oral dosage forms can increase the dissolution rate of poorly soluble drugs. Spray drying is one process that can be used to prepare solid dispersions. Spray dried solid dispersions of griseofulvin, poly[N-(2-hydroxypropyl)methacrylate] (PHPMA) and polyvinylpyrrolidone (PVP) were prepared from acetone and water. When methanol was substituted for water, the morphology, stability and dissolution properties of the solid dispersion changed dramatically. The glass transition temperature for the ternary solid dispersion (GF, PHPMA, and PVP) shifted from 83°C (acetone/water) to 103°C for the acetone/methanol system. These differences in the dispersions are thought to derive from conformational variations of the polymers in solution prior to spray drying. Both PHPMA and PVP formed globules in solution of a size range between 16 and 33 nm. The effect of drug and polymer concentration in solution (before spray drying) on the properties of the solid dispersion was studied. It was found that solid dispersions that were prepared using lower concentrations of drug and polymers in solutions resulted in the formation of particles that display a lower relaxation rate. This result supports the hypothesis that the polymer conformation may significantly change the properties of the solid dispersion. © 2009 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 98:4724–4737, 2009     

尼莫地平固体分散体的研究

目的 制备尼莫地平固体分散体,增加其溶出速度.方法 应用聚乙烯吡咯烷酮（PVP）为载体,采用喷雾干燥制备尼莫地平固体分散体,通过差示扫描量热分析（DSC）和X-射线粉末衍射分析鉴别药物在载体中的存在状态,并进行了体外溶出度研究.结果 尼莫地平在载体中以分子状态存在,尼莫地平固体分散体的溶出度与尼莫地平原料药和原料药载体物理混合物相比有显著提高,载体比例越大,药物溶出越快,药物载体比例为1：3时t50仅0.972 6 min,结论聚乙烯吡咯烷酮（PVP）作为尼莫地平固体分散体的载体载药量大;喷雾干燥工艺重现性好,分散体颗粒无需粉碎可满足各类固体制剂的制备要求,是一种较理想的尼莫地平固体分散体的制备方法.     

Development of raloxifene-solid dispersion with improved oral bioavailability via spray-drying technique

The purpose of this study was to develop a raloxifene-loaded solid dispersion with enhanced dissolution rate and bioavailability via spray-drying technique. Solid dispersions of raloxifene (RXF) were prepared with PVP K30 at weight ratios of 1:4, 1:6 and 1:8 using a spray-drying method, and characterized by differential scanning calorimetry, X-ray powder diffraction, scanning electron microscopy, and solubility and dissolution tests. The bioavailability of the solid dispersion in rats was also evaluated compared to those of RXF powder and commercial product. Results showed that the RXF-loaded solid dispersion was in amorphous form with increased solubility and dissolution rate. The absorption of RXF from solid dispersion resulted in approximately 2.6-fold enhanced bioavailability compared to pure drug. Moreover, RXF-loaded solid dispersion gave similar AUC, C_max and T_max values to the commercial product, suggesting that it was bioequivalent to the commercial product in rats. These findings suggest that an amorphous solid dispersion of RXF could be a viable option for enhancing the oral bioavailability of RXF.     

Physicochemical characterization and dissolution study of solid dispersions of Lovastatin with polyethylene glycol 4000 and polyvinylpyrrolidone K30

Solid dispersions in water-soluble carriers have attracted considerable interest as a means of improving the dissolution rate, and hence possibly bioavailability, of a range of hydrophobic drugs. The aim of the present study was to improve the solubility and dissolution rate of a poorly water-soluble drug, Lovastatin, by a solid dispersion technique. Solid dispersions were prepared by using polyethylene glycol 4000 (PEG 4000) and polyvinylpyrrolidone K30 (PVP K30) in different drug-to-carrier ratios. Dispersions with PEG 4000 were prepared by fusion-cooling and solvent evaporation, whereas dispersions containing PVP K30 were prepared by solvent evaporation technique. These new formulations were characterized in the liquid state by phase solubility studies and in the solid state by differential scanning calorimetry, X-ray powder diffraction, and FT-IR spectroscopy. The aqueous solubility of Lovastatin was favored by the presence of both polymers. The negative values of the Gibbs free energy and enthalpy of transfer explained the spontaneous transfer from pure water to the aqueous polymer environment. Solid-state characterization indicated Lovastatin was present as amorphous material and entrapped in polymer matrix. In contrast to the very slow dissolution rate of pure Lovastatin, the dispersion of the drug in the polymers considerably enhanced the dissolution rate. This can be attributed to improved wettability and dispersibility, as well as decrease of the crystalline and increase of the amorphous fraction of the drug. Solid dispersion prepared with PVP showed the highest improvement in wettability and dissolution rate of Lovastatin. Even physical mixture of Lovastatin prepared with both polymers also showed better dissolution profile than that of pure Lovastatin. Tablets containing solid dispersion prepared with PEG and PVP showed significant improvement in the release profile Lovastatin compared with tablets containing Lovastatin without PEG or PVP.     

Physicochemical Characterization and Dissolution Study of Solid Dispersions of Lovastatin with Polyethylene Glycol 4000 and Polyvinylpyrrolidone K30

Solid dispersions in water-soluble carriers have attracted considerable interest as a means of improving the dissolution rate, and hence possibly bioavailability, of a range of hydrophobic drugs. The aim of the present study was to improve the solubility and dissolution rate of a poorly water-soluble drug, Lovastatin, by a solid dispersion technique. Solid dispersions were prepared by using polyethylene glycol 4000 (PEG 4000) and polyvinylpyrrolidone K30 (PVP K30) in different drug-to‐carrier ratios. Dispersions with PEG 4000 were prepared by fusion-cooling and solvent evaporation, whereas dispersions containing PVP K30 were prepared by solvent evaporation technique. These new formulations were characterized in the liquid state by phase solubility studies and in the solid state by differential scanning calorimetry, X-ray powder diffraction, and FT-IR spectroscopy. The aqueous solubility of Lovastatin was favored by the presence of both polymers. The negative values of the Gibbs free energy and enthalpy of transfer explained the spontaneous transfer from pure water to the aqueous polymer environment. Solid-state characterization indicated Lovastatin was present as amorphous material and entrapped in polymer matrix. In contrast to the very slow dissolution rate of pure Lovastatin, the dispersion of the drug in the polymers considerably enhanced the dissolution rate. This can be attributed to improved wettability and dispersibility, as well as decrease of the crystalline and increase of the amorphous fraction of the drug. Solid dispersion prepared with PVP showed the highest improvement in wettability and dissolution rate of Lovastatin. Even physical mixture of Lovastatin prepared with both polymers also showed better dissolution profile than that of pure Lovastatin. Tablets containing solid dispersion prepared with PEG and PVP showed significant improvement in the release profile of Lovastatin compared with tablets containing Lovastatin without PEG or PVP.     

Development of novel ibuprofen-loaded solid dispersion with improved bioavailability using aqueous solution

To develop a novel ibuprofen-loaded solid dispersion with enhanced bioavailability, various ibuprofen-loaded solid dispersions were prepared with water, HPMC and poloxamer. The effect of HPMC and poloxamer on aqueous solubility of ibuprofen was investigated. The dissolution and bioavailability of solid dispersion in rats were then evaluated compared to ibuprofen powder. When the amount of carrier increased with a decreased in HPMC/poloxamer ratio, the aqueous solubility of ibuprofen was elevated. The solid dispersion composed of ibuprofen/HPMC/poloxamer at the weight ratio of 10:3:2 improved the drug solubility approximately 4 fold. It gave significantly higher initial plasma concentration, AUC and Cmax of drug than did ibuprofen powder in rats. The solid dispersion improved the bioavailability of drug about 4-fold compared to ibuprofen powder. Thus, this ibuprofen-loaded solid dispersion with water, HPMC and poloxamer was a more effective oral dosage form for improving the bioavailability of poor water-soluble ibuprofen.