Failure load of patellar tendon grafts at the femoral side: 10- versus 20-mm-bone blocks

The aim of the study was to investigate whether use of short bone blocks is safe in anterior cruciate ligament (ACL) reconstruction. Our hypothesis was that the smaller 10-mm-length bone blocks will fail at lower loads than 20-mm-bone blocks. Ten paired human cadaver knees were randomly assigned to the 10- or 20-mm group (group 1 and 2) and underwent bone–patellar tendon–bone femoral fixation with interference screw. Tensile tests were performed using a tensile testing machine (Instron). Stiffness, failure load and failure mode were recorded. Median stiffness was 72 N/mm (16–103) for 10-mm-bone blocks and 91 N/mm (40–130) for 20-mm-bone blocks. Median failure loads were 402 N (87–546) for 10-mm-long bone block and 456 N (163–636) for 20-mm-bone blocks. There was no statistically significant difference between groups (P = 0.35). All bone–patellar tendon–bone grafts were pulled out of the femoral tunnel with interference screw, due to slippage. We concluded that a 10-mm-long bone block was not significantly weaker than a 20-mm-long bone block. Failure loads of a 10-mm-bone block exceeded loading values at passive and active extension of the knee under normal conditions. Ten millimetre bone blocks offered sufficient fixation strength in ACL reconstruction.     

Biomechanical properties of patellar and hamstring graft tibial fixation techniques in anterior cruciate ligament reconstruction: experimental study with roentgen stereometric analysis

BACKGROUND: Reliable fixation of the soft hamstring grafts in ACL reconstruction has been reported as problematic. HYPOTHESIS: The biomechanical properties of patellar tendon (PT) grafts fixed with biodegradable screws (PTBS) are superior compared to quadrupled hamstring grafts fixed with BioScrew (HBS) or Suture-Disc fixation (HSD). STUDY DESIGN: Controlled laboratory study with roentgen stereometric analysis (RSA). METHODS: Ten porcine specimens were prepared for each group. In the PT group, the bone plugs were fixed with a 7 x 25 mm BioScrew. In the hamstring group, four-stranded tendon grafts were anchored within a tibial tunnel of 8 mm diameter either with a 7 x 25 mm BioScrew or eight polyester sutures knotted over a Suture-Disc. The grafts were loaded stepwise, and micromotion of the graft inside the tibial tunnel was measured with RSA. RESULTS: Hamstring grafts failed at lower loads (HBS: 536 N, HSD 445 N) than the PTBS grafts (658 N). Stiffness in the PTBS group was much greater compared to the hamstring groups (3500 N/mm versus HBS = 517 N/mm and HSD = 111 N/mm). Irreversible graft motion after graft loading with 200 N was measured at 0.03 mm (PTBS), 0.38mm (HBS), and 1.85mm (HSD). Elasticity for the HSD fixation was measured at 0.67 mm at 100 N and 1.32 mm at 200 N load. CONCLUSION: Hamstring graft fixation with BioScrew and Suture-Disc displayed less stiffness and early graft motion compared to PTBS fixation. Screw fixation of tendon grafts is superior to Suture-Disc fixation with linkage material since it offers greater stiffness and less graft motion inside the tibial tunnel. Clinical Relevance: Our results revealed graft motion for hamstring fixation with screw or linkage material at loads that occur during rehabilitation. This, in turn, may lead to graft laxity.     

The effect of overlapping on the primary stability of osteochondral grafts in mosaicplasty

Our goal was to determine the primary stability of overlapping osteochondral grafts used in mosaicplasty by studying the effect of overlapping in an ex vivo model. Osteochondral grafts, 10 mm in diameter, were transplanted from the trochlea of cow femurs to the weight-bearing area of the lateral femoral condyle with 0, 15, or 30% overlap. The grafts were pushed in with a probe at a rate of 2 mm/min, and load (N)-displacement (mm) curves were recorded. In Group I (control, 0% overlap), insertion 1 and 2 mm below the cartilage level could be reached at 572.3 +/- 273.6 and 999.3 +/- 427.6 N, respectively. In Group II (15% overlap), insertion 1 and 2 mm below the cartilage level could be reached at 263.6 +/- 91.7 and 746.6 +/- 88.0 N, respectively. In Group III (30% overlap), insertion 1 and 2 mm below the cartilage level could be reached at 179.4 +/- 31.2 and 657.0 +/- 106.5 N, respectively. The loads that were necessary to produce a 1-mm dent in the grafts were significantly different between Groups I and II and Groups I and III (p < 0.05). These results suggest that stability may be reduced by graft overlapping in mosaicplasty surgery. The results of this ex vivo animal study contribute to a more complete understanding of the primary stability of osteochondral grafts in an overlapping position as well as postoperative protocols.     

Biomechanical properties of the central third patellar tendon graft: effect of rotation

The results of this study suggest that the central third of the patellar tendon may be stronger than previously reported. The mean ultimate load of a 15-mm bone-patellar tendon-bone composite was 4389 N (± 709 N); of the 10-mm wide composites, 2977 N (± 516 N); and of the 7-mm composites, 2238 N (± 316 N). Twisting the graft 90° increased the strength (P < 0.05). Further twisting to 180° had no significant effect compared with twisting to 90°. This study supports the practice of using smaller (10 mm) bone-patellar tendon-bone grafts to avoid the potential complications of patellar fracture and graft impingement in the notch, and suggests the value of rotating the graft prior to tibial fixation.     

Mechanical effects of autogenous osteochondral surgical grafting procedures and instrumentation on grafts of articular cartilage

PURPOSE: To analyze the mechanical effects of autogenous osteochondral grafting procedures on articular cartilage. METHODS: The intensity, duration, and interval (indexes of stiffness, surface irregularity, and thickness) of the cartilage were assessed in a porcine model using an ultrasonic measurement system. In 7 of 12 knees, 6-mm-diameter plugs were harvested from the donor knees and grafted into 5-mm recipient holes at 3 different points per knee (21 plugs). In the remaining 5 knees, 5-mm plugs were harvested and returned to their original position (28 plugs). RESULTS: No significant differences in the intensity, duration, and interval of the cartilage were observed with the plugs before harvesting and after grafting by the paired t test. The 3 indexes of the 6- and 5-mm plugs that were grafted correlated significantly with those before they were. CONCLUSIONS: These results suggest that osteochondral graft surgery does not affect the stiffness, surface irregularity, and thickness of the cartilage of the plugs at time zero.     

A new interference nail fixation for anterior cruciate ligament soft tissue grafts

We present a new device for femoral and tibial fixation in anterior cruciate ligament reconstruction using soft tissue. We evaluated the method biomechanically in pullout tests using human cadaver knee joints. Fixation strengths ranged from 300 ± 60 to 600 ± 50 N (mean 400 ± 50 N). This corresponds to loads in the graft during aggressive rehabilitation although cadaveric specimens were used. With respect to primary fixation strength this implant is a reasonable alternative for anterior cruciate ligament graft fixation. Received: 6 October 1999 Accepted: 5 March 2000     

Fixation strength of interference screw fixation in bovine,young human,and elderly human cadaver knees: Influence of insertion torque,tunnel-bone block gap,and interference

A failure analysis of interference screw fixation was performed to test the hypothesis that bovine and/or elderly human cadavers are appropriate models for bonepatellar tendon-bone anterior cruciate ligament (ACL) reconstruction fixation studies. Failure mode is an important criterion for validating experimental models. The bovine, young human, and elderly human failure loads were 799±261 N, 655±186 N, and 382±118 N, respectively, and the failure modes were 75%, 69%, and 30% tissue failures, respectively. The similarities between the bovine and young human models in failure loads and failure modes indicate that bovine models are appropriate for ACL reconstruction fixation studies. The statistically significant differences between the young human and elderly human models in failure loads and failure modes indicate that elderly human cadavers are not an appropriate model for ACL reconstruction fixation studies. The differences in failure modes are consistent with previous studies using elderly human cadavers in which the predominant failure mode was bone block pullout. The tissue failures observed in the bovine and young human models contradict previous studies suggesting fixation strength is the weakest link in bone-patellar tendon-bone ACL reconstruction. Results of linear regression modeling showed statistically significant correlations between insertion torque and failure load (R ²=0.44,P<0.0001) and interference (defined as the screw outer thread diameter minus the tunnel-bone block gap) and insertion torque (R ²=0.18,P=0.003) when data from all models was combined. Results for the bovine model multiple regression showed a statistically significant regression of insertion torque (linear) and interference (quadritic) versus failure load (R ²=0.56,P=0.02). Regression slopes for screw diameter (P=0.52) and gap size (P=1.00) were not statistically significant. These results indicate that insertion torque and interference are independent predictors of failure load and should be included in future interference screw studies in addition to bone block dimensions, tunnel size, gap size, and screw diameter. Clinicians may consider using insertion torque and interference as indicators of postoperative graft fixation regarding rehabilitation decisions.     

A biomechanical comparison of initial soft tissue tibial fixation devices: the Intrafix versus a tapered 35-mm bioabsorbable interference screw

BACKGROUND: Biomechanical testing of the Intrafix device has not been performed using human tibiae. HYPOTHESIS: The Intrafix device would provide comparable or superior tibial fixation of a quadrupled hamstring tendon graft to a 35-mm-long bioabsorbable interference screw. STUDY DESIGN: In vitro, biomechanical study. METHODS: Eight paired human tibiae and 16 quadrupled hamstring tendon grafts were divided into 2 groups. Each quadrupled hamstring tendon graft was fixed in a tunnel sized to 0.5 mm graft diameter with either an Intrafix device or a screw. RESULTS: Displacement at failure was greater in the Intrafix group (17.3 +/- 4.6 mm versus 10.9 +/- 4.4 mm, P =.002). Load at failure (796 +/- 193 N versus 647 +/- 269 N), stiffness (49.2 +/- 21.9 N/mm versus 64.5 +/- 22 N/mm), and bone mineral density (0.74 +/- 0.15 gm/cm(3) versus 0.74 +/- 0.14 gm/cm(3)) did not display significant differences for the Intrafix device and the screw, respectively (P >.05). CONCLUSIONS: Displacement at failure was greater for the Intrafix device. CLINICAL RELEVANCE: Increased displacement at failure for the Intrafix group suggests slippage from sheath channel deployment. Concentric fixation may not occur when less than optimal tibial bone mineral density increases the difficulty of attaining precise sheath deployment and quadrupled hamstring tendon graft strand alignment.     

Effect of screw length on bioabsorbable interference screw fixation in a tibial bone tunnel

Initial tibial fixation strength is the weak link after anterior cruciate ligament reconstruction with a quadrupled hamstring tendon graft fixed with bioabsorbable interference screws. The purpose of this study was to determine the biomechanical differences between 28-mm and tapered 35-mm interference screws for tibial fixation of a soft tissue graft in 16 young cadaveric tibias. Failure mode, displacement before failure, and ultimate failure load were tested with a testing machine aligned with the tibial tunnel to simulate a worst-case scenario. The mode of failure was graft slippage past the screw in all but one of the specimens. The mean maximum load at failure of the 28-mm screw was 594.9 +/- 141.0 N, with mean displacement at failure of 10.97 +/- 2.20 mm. The mean maximum load at failure of the 35-mm screw was 824.9 +/- 124.3 N, with a mean displacement to failure of 14.38 +/- 2.15 mm. The 38% difference in mean maximal load at failure was significant. Important variables in hamstring tendon graft fixation within a bone tunnel include bone mineral density, dilatation, gap size, screw placement, and screw width and length. Attention to these variables will help to provide secure graft fixation during biologic incorporation throughout the rehabilitation period.     

The effect of angled osteochondral grafting on contact pressure: a biomechanical study

BACKGROUND: Flush osteochondral plugs can reduce contact pressure compared with an empty defect in the articular cartilage. However, incongruities such as graft angulation have an unknown effect. HYPOTHESIS: Incongruity of the articular cartilage after osteochondral transplantation affects articular surface contact pressure. STUDY DESIGN: Controlled laboratory study. METHODS: An 80-N load was applied with a material testing system for 120 seconds to the femoral condyles of 50 fresh swine knees. Contact pressures were measured using Prescale super low film. Five conditions were tested: (1) intact articular surface; (2) surface with 4.5-mm-diameter circular defect; (3) defect grafted with a flush 4.5-mm-diameter plug from the contralateral condyle; (4) defect grafted with a 30 degrees angled 4.5-mm-diameter plug, with lower edge flush (tip elevated with respect to the adjacent surface); and (5) defect grafted with a 30 degrees plug, with tip flush to the adjacent surface (lower edge sunk). Angled grafts were obtained using a rotational bearing vise aligned with a 30 degrees fixed-angle track. The film was digitally scanned and analyzed, and standard statistical tests were performed. RESULTS: Mean peak pressures of intact cartilage (8.57 kg/cm2), flush graft (9.81 kg/cm2), and sunk and angled graft (9.15 kg/cm2) were not significantly different (P < .5). The mean pressures for defects (12.01 kg/cm2) and the elevated angled graft (14.50 kg/cm2) were significantly (P < .05) higher than that of intact cartilage. CLINICAL RELEVANCE: Slightly sunk grafts were still able to reduce elevated contact pressures to normal levels. However, elevated angled grafts increased contact pressure. These results suggest that it is preferable to leave an edge slightly sunk rather than elevated.     

Pullout strength of tibial graft fixation in anterior cruciate ligament replacement with a patellar tendon graft: interference screw versus staple fixation in human knees

The endoscopic single incision technique for anterior cruciate ligament (ACL) reconstruction with a femoral half-tunnel may lead to a graft/tunnel mismatch and subsequent protrusion of the block from the tibial tunnel. The typical tibial fixation with an interference screw is not possible in these cases. Fixation with staples in a bony groove inferior to the tunnel outlet can be used as an alternative technique. Current literature does not provide biomechanical data of either fixation technique in a human model. This study was performed to evaluate the primary biomechanical parameters of this technique compared with a standard interference screw fixation of the block. Fifty-five fresh-frozen relatively young (mean age 44 years) human cadaver knee joints were used. Grafts were harvested from the patellar tendon midportion with bone blocks of 25 mm length and 9 mm width. A 10-mm tibial tunnel was drilled from the anteromedial cortex to the center of the tibial insertion of the ACL. Three different sizes of interference screws (7 × 30, 9 × 20, 9 × 30 mm) were chosen as a standard control procedure (n = 40). For tibial bone-block fixation the graft was placed through the tunnel, and the screw was then inserted on the cancellous or the cortical surface, respectively. Fifteen knees were treated by staple fixation. A groove was created inferior to the tunnel outlet with a chisel. The bone block was fixed in this groove with two barbed stainless steel staples. Tensile testing in both groups was carried out under an axial load parallel to the tibial tunnel in a Zwick testing machine with a velocity of 1 mm/s. Dislocation of the graft and stiffness were calculated at 175 N load. Maximum load to failure using interference screws varied between 506 and 758 N. Load to failure using staples was 588 N. Dislocation of the graft ranged between 3.8 and 4.7 mm for interference screw fixation and was 4.7 mm for staples. Stiffness calculated at 175 N load was significantly higher in staple fixation. With either fixation technique, the recorded failure loads were sufficient to withstand the graft loads which are to be expected during the rehabilitation period. Staple fixation of the bone block outside of the tunnel resulted in a fixation strength comparable to interference screw fixation. Received: 2 September 1996 Accepted: 30 January 1997     

Biomechanical and histological evaluation of osteochondral transplantation in a rabbit model

BACKGROUND: Biomechanical and histological properties of osteochondral transplantation have not been extensively examined. HYPOTHESIS: Osteochondral grafts have properties similar to native articular cartilage. STUDY DESIGN: Controlled laboratory study. METHODS: A 2.7 mm (diameter) x 4.0 mm (depth) osteochondral defect was created in 17 New Zealand white rabbit knees. An osteochondral graft, harvested from the contralateral knee, was transplanted into the defect. Eight rabbits were sacrificed each at 6 and 8 weeks. RESULTS: The 12-week grafts (1213.6 +/- 309.0 N/mm) had significantly higher stiffness than the 6-week grafts (483.1 +/- 229.1 N/mm; P <.001) and of normal cartilage (774.8 +/- 117.1 N/mm; P <.003). Stiffness of the 6-week grafts was significantly lower than normal cartilage (P <.036). At all time points, full-thickness defects had significantly lower stiffness than normal cartilage (P <.001). Histologically, transplanted grafts scored significantly higher than the full-thickness defects (P <.001). The defects showed inconsistent, fibrocartilage healing. The grafts demonstrated cartilage viability, yet with a persistent cleft between the graft and host. CONCLUSIONS: Osteochondral transplants undergo increased stiffness in the short term, with evidence of structurally intact grafts. Clinical Relevance: Osteochondral transplantation may be a viable treatment option; however, long-term investigation on graft function is necessary.     

Initial fixation strength of two bioabsorbable pins for the fixation of hamstring grafts compared to interference screw fixation: single cycle and cyclic loading

BACKGROUND: During the early postoperative period, the fixation of a hamstring graft to the bone tunnel is the primary factor in limiting rehabilitation. HYPOTHESIS: The initial fixation strength of a double cross pin fixation technique is comparable with the biodegradable interference screw fixation technique. STUDY DESIGN: Experimental laboratory study. METHODS: The authors examined the initial fixation strength of two 3.3-mm bioabsorbable pins compared to interference screws for hamstring grafts in bovine knees. RESULTS: Analysis of yield load, maximum load, and stiffness in the single-cycle loading test showed no statistically significant differences for cross pin and interference fixation (P <.05). For cross pins and interference screws, the mean displacement under 1000 cycles to 250 N was 5.07 ( +/- 1.9) mm and 4.81 ( +/- 2.5) mm, stiffness 252 ( +/- 78) N/mm and 289 ( +/- 148) N/mm. Only grafts fixed with cross pins survived 1000 cycles to 450 N. CONCLUSION: The initial fixation strength of the double cross pin technique is comparable to that of interference screw fixation with a stiffness comparable to that of the native ACL. Clinical Relevance: Hamstring graft fixation using two cross pins provides an alternative to bioabsorbable interference screw fixation.     

Close-looped graft suturing improves mechanical properties of interference screw fixation in ACL reconstruction

Purpose

In anterior cruciate ligament reconstruction with looped soft-tissue grafts, an interference screw is frequently used for tibial fixation. This study compared three alternatives thought to improve the initial mechanical properties of direct bioabsorbable interference screw fixation: suturing the graft to close the loop, adding a supplementary staple, or increasing the oversize of the screw diameter relative to the bone tunnel from 1 to 2 mm.

Methods

Twenty-eight porcine tibiae and porcine flexor digitorum profundus tendons were randomized into four testing groups: a base fixation using 10-mm-diameter screw with open-looped graft, base fixation supplemented by an extracortical staple, base fixation but closing the looped graft by suturing its ends, and base fixation but using an 11-mm screw. Graft and bone tunnel diameters were 9 mm in all specimens. Constructs were subjected to cyclic tensile load and finally pulled to failure to determine their structural properties.

Results

The main mode of failure in all groups was pull-out of tendon strands after slippage past the screw. The sutured graft group displayed significantly lower residual displacement (mean value reduction: 47–67 %) and higher yield load (mean value increase: 38–54 %) than any alternative tested. No other statistical differences were found.

Conclusions

Suturing a soft-tissue graft to form a closed loop enhanced the initial mechanical properties of tibial fixation with a bioabsorbable interference screw in anterior cruciate ligament reconstructions using a porcine model, and thus, this may be an efficient means to help in reducing post-operative laxity and early clinical failure. No mechanical improvement was observed for an open-looped tendon graft by adding an extracortical staple to supplement the screw fixation or by increasing the oversize of the screw to tunnel diameter from 1 to 2 mm.     

Bone plug length and loading angle determine the primary stability of patellar tendon-bone grafts in press-fit ACL reconstruction

The present study was conducted to evaluate the influence of bone-plug length on the primary stability of patellar tendon-bone grafts, using a femoral press-fit fixation technique. Forty-eight human PTB grafts with a patellar bone-plug length of 15 mm and 25 mm were obtained from 24 human cadavers (mean age 72 years) and implanted to porcine femora in a press-fit fixation technique. Tensile loading was performed at 10 mm/s until failure at varying loading angles of 0°, 30° and 60°. Compared to 25 mm, a significant decrease of primary graft stability was recorded in the testing of 15-mm bone plugs. For both plug lengths, the ultimate load to failure increased with rising the loading angles. While axial graft loading exclusively caused plug dislocation, the predominant mode of failure was tendon rupture at 60° loading angle. We conclude that 15-mm bone plugs do not result in a sufficient stability for early aggressive rehabilitation and therefore 25-mm bone plugs are recommended for the femoral press-fit technique.     

Coracoclavicular ligament reconstruction: biomechanical comparison of tendon graft repairs to a synthetic double bundle augmentation

For currently presented anatomical coracoclavicular ligament repairs issues such as autologous tendon graft versus synthetic suture augmentation and the optimum fixation strategies for both types of reconstruction are not solved. The purpose of the study was to compare the biomechanical properties of different tendon graft repairs to the characteristics of a synthetic polyester augmentation. Four anatomical coracoclavicular ligament repairs were biomechanically tested: 5 mm coracoclavicular tendon loop with suture fixation, tendon loop with flip button fixation, tendon loop with interference screw fixation versus a double 1.0-mm polyester repair with flip button fixation. The biomechanical testing included cyclic superio-inferior loading and a subsequent load to failure protocol. The ultimate failure loads were significantly higher for the double polyester/flip button repair (927 N) compared to all tendon repair techniques (maximum 640 N). In contrast the stiffness level was higher for the tendon repairs compared to the polyester/flip button repair (68.7 N/mm) but strongly dependent on the fixation technique (interference screw 97.2 N/mm, flip button 84.9 N/mm, side to side suture 60.9 N/mm). A synthetic coracoclavicular augmentation using a polyester suture provides adequate structural properties compared to a tendon repair. Therefore the decision for a tendon graft should be made by the necessity of a biologic substrate rather than by the assumption of a biomechanical advantage.     

Soft tissue tendon graft fixation in serially dilated or extraction-drilled tibial tunnels: a porcine model study using high-resolution quantitative computerized tomography

BACKGROUND: Tibial tunnel preparation may contribute to improved soft tissue graft fixation. HYPOTHESIS: Step dilation produces greater tunnel wall bone volume than does extraction drilling and increases fixation strength. Bioabsorbable interference screw divergence decreases fixation strength, regardless of tunnel preparation method. STUDY DESIGN: Controlled laboratory study. METHODS: Twenty porcine tibias were divided into 2 groups of 10 with matching mean apparent bone mineral density. One group received 9-mm-diameter extraction-drilled tunnels, and the other group received 7-mm-diameter extraction-drilled tunnels followed by step dilation to 9 mm. High-resolution quantitative computerized tomography scans and voxel analysis techniques determined tunnel wall bone volume fraction. Screws secured 8.5-mm-diameter porcine grafts in the tunnels. Repeat scans were used to determine screw divergence. Cyclic loading was performed in a servohydraulic device before load to failure testing. RESULTS: The step dilation group had greater tunnel wall bone volume/total volume than did the extraction drilled group; however, a significant increase in fixation strength was not detected. Specimens with screw divergence angles less than 15 degrees had superior fixation and insertion torques compared with specimens with angles 15 degrees or more. Screw divergence correlated more strongly with fixation strength than did mean apparent bone mineral density or screw insertion torque. CONCLUSION: Step dilation increased tunnel wall bone volume/total volume, but fixation strength did not improve. Screw divergence >or=15 degrees decreases graft-bone tunnel fixation whether or not step dilation is performed. CLINICAL RELEVANCE: Screw alignment plays a greater role in anterior cruciate ligament graft fixation than does extraction drilling or step dilation tunnel preparation methods in healthy bone.     

Cyclic pull-out strength of hamstring tendon graft fixation with soft tissue interference screws. Influence of screw length

Blunt-threaded interference screws used for fixation of hamstring tendons in anterior cruciate ligament reconstructions provide aperture fixation and may provide a biomechanically more stable graft than a graft fixed further from the articular surface. It is unknown if soft tissue fixation strength using interference screws is affected by screw length. We compared the cyclic and time-zero pull-out forces of 7 x 25 mm and 7 x 40 mm blunt-threaded metal interference screws for hamstring graft tibial fixation in eight paired human cadaveric specimens. A four-stranded autologous hamstring tendon graft was secured by a blunt-threaded interference screw into a proximal tibial tunnel with a diameter corresponding to the graft width. Eight grafts were secured with a 25-mm length screw while the other eight paired grafts were secured with a 40-mm length screw. During cyclic testing, slippage of the graft occurred as the force of pull became greater with each cycle until the graft-screw complex ultimately failed. All grafts failed at the fixation site, with the tendon being pulled past the screw. There were no measurable differences in the mean cyclic failure strength, pull-out strength, or stiffness between the two sizes of screws. Although use of the longer screw would make removal technically easier should revision surgery be necessary, it did not provide stronger fixation strength than the shorter, standard screw as had been postulated.     

A biomechanical evaluation of transcondylar femoral fixation of anterior cruciate ligament grafts

BACKGROUND: Interference screw fixation of the graft in anterior cruciate ligament reconstruction is considered the gold standard, but limited clinical experience suggests that transcondylar fixation is equally effective. PURPOSE: To compare transcondylar and interference screw fixation. STUDY DESIGN: Ex vivo biomechanical study. METHODS: Twenty pairs of unembalmed knees underwent anterior cruciate ligament reconstruction with patellar tendon autografts. In 1 knee of each pair, the bone plug was stabilized in the femoral tunnel with standard interference screws; in the other knee, transcondylar screws were used. Testing to failure occurred immediately or after 1000 cycles of sinusoidal loading (30 to 150 N) (20 paired reconstructions each). Fixation stiffness, strength, graft creep, displacement amplitude, and change in amplitude were measured and compared (repeated measures anaylsis of variance with Tukey test; P <.05). RESULTS: There was no significant difference in acute strength, maximum load within 3 mm, or stiffness between transcondylar fixation (410 +/- 164 N, 183 +/- 93 N, and 49.6 +/- 28 N/mm, respectively) and interference fixation (497 +/- 216 N, 206 +/- 115 N, and 61 +/- 37.8 N/mm, respectively). Similarly, there was no significant difference in cyclic strength, maximum load within 3 mm, or stiffness between transcondylar fixation (496 +/- 214 N, 357 +/- 82.9 N, and 110 +/- 27.4 N/mm, respectively) and interference fixation (552 +/- 233 N, 357 +/- 76.2 N, and 112 +/- 26.8 N/mm, respectively). Predominant modes of failure were bone plug pullout (transcondylar fixation) and tendon failure or bone plug fracture (interference fixation). CONCLUSIONS: Transcondylar screw fixation of the patellar tendon autograft into the femoral tunnel performed mechanically as well as interference screw fixation. CLINICAL RELEVANCE: The results suggest that transcondylar and interference screws provide similar fixation for anterior cruciate ligament reconstruction.     

Effects of knee flexion angles for graft fixation on force distribution in double-bundle anterior cruciate ligament grafts

BACKGROUND: In double-bundle anterior cruciate ligament reconstruction, overloading either 1 of the 2 grafts should be avoided to decrease the risk of graft failure. HYPOTHESIS: Overloading of the posterolateral graft may occur when it is fixed at 30 degrees of knee flexion because the posterolateral bundle is elongated as the knee approaches extension. STUDY DESIGN: Controlled laboratory study. METHODS: Ten human cadaveric knees were tested at (1) intact, (2) anterior cruciate ligament-deficient, (3) double-bundle anterior cruciate ligament reconstruction with the anteromedial and posterolateral grafts fixed at 60 degrees of flexion and full extension, respectively (fixation 60/FE), and (4) double-bundle anterior cruciate ligament reconstruction with both grafts fixed at 30 degrees of flexion simultaneously (fixation 30/30). Two external loading conditions simulating clinical examinations were used: (1) 134-N anterior tibial load and (2) combined rotatory loads of 10 N x m valgus and 5 N x m internal tibial torques. Data on knee kinematics and in situ forces in the 2 bundles of the intact anterior cruciate ligament and the respective grafts were obtained. RESULTS: In response to 134-N anterior tibial load, knee kinematics and in situ force in the grafts were similar to the intact knee for both fixation protocols. The force in the anteromedial graft for fixation 60/FE was 34% higher, whereas the posterolateral graft for fixation 30/30 was 46% higher, compared with the intact anteromedial and posterolateral bundles, respectively. In response to combined rotatory loads, the posterolateral graft for fixation 30/30 carried 67% higher load than did the intact posterolateral bundle. CONCLUSION: Fixation 30/30 overloaded the posterolateral graft, whereas fixation 60/FE overloaded the anteromedial graft. CLINICAL RELEVANCE: In double-bundle anterior cruciate ligament reconstruction, even though overall forces in the graft are the same as intact anterior cruciate ligament, the force distributions may not be the same as the intact bundles, and overloading of 1 of the 2 grafts may occur.