Preparation and Application of Self-Curing Magnesium Phosphate Cement Concrete with High Early Strength in Severe Cold Environments

The early strength of magnesium phosphate cement (MPC) decreases sharply in severe cold environments ≤−10 °C, with the 2 h compressive strength falling to 3.5 MPa at−20 °C. Therefore, it cannot be used as a repair material for emergency repair construction in such environments. In this study, MPC is adapted for use in such cold environments by replacing part of the dead-burned magnesia (M) in the mixture with a small amount of light-burned magnesia (LBM) and introducing dilute phosphoric acid (PA) solution as the mixing water. The heat released by the highly active acid–base reaction of PA and LBM stimulates an MPC reaction. Moreover, the early strength of the MPC significantly improves with the increase in the Mg²⁺ concentration and the initial reaction temperature of the MPC paste, which enables MPC hardening in severe cold environments. Although the morphology of the reaction products of the MPC is poor and the grain plumpness and size of the struvite crystals are remarkably reduced, the early strength of MPC prepared in the severe cold environment is close to that of MPC prepared under normal temperature. Furthermore, the increases in the early reaction temperature and early strength of magnesium phosphate cement concrete (MPCC) are significantly improved when the PA concentration in the mixing water and the LBM/M ratio are 10% and 4–6% at −10 °C and 20% and 6–8% at −20 °C, respectively. Moreover, self-curing of MPCC can be realized even at −20 °C, at which temperature the 2 h and 24 h compressive strength of MPCC reach 36 MPa and 45 MPa, respectively.     

Thermophysical and Mechanical Properties of Hardened Cement Paste with Microencapsulated Phase Change Materials for Energy Storage

In this research, structural-functional integrated cement-based materials were prepared by employing cement paste and a microencapsulated phase change material (MPCM) manufactured using urea-formaldehyde resin as the shell and paraffin as the core material. The encapsulation ratio of the MPCM could reach up to 91.21 wt%. Thermal energy storage cement pastes (TESCPs) incorporated with different MPCM contents (5%, 10%, 15%, 20% and 25% by weight of cement) were developed, and their thermal and mechanical properties were studied. The results showed that the total energy storage capacity of the hardened cement specimens with MPCM increased by up to 3.9-times compared with that of the control cement paste. The thermal conductivity at different temperature levels (35–36 °C, 55–56 °C and 72–74 °C) decreased with the increase of MPCM content, and the decrease was the highest when the temperature level was 55–56 °C. Moreover, the compressive strength, flexural strength and density of hardened cement paste decreased with the increase in MPCM content linearly. Among the evaluated properties, the compressive strength of TESCPs had a larger and faster degradation with the increase of MPCM content.     

Effect of Early Curing Temperature on the Tunnel Fire Resistance of Self-Compacting Concrete Coated with Aerogel Cement Paste

In this paper, the effect of early curing temperature on the tunnel fire resistance of self-compacting concrete (SCC) coated with aerogel cement paste (ACP) was studied. The physical properties in terms of the compressive strength, flexural strength, and thermal conductivity of ACP were tested under different early curing temperatures. The tunnel fire resistance of ACP and SCC coated with ACP was determined, and the microstructure of ACP and SCC after a tunnel fire were characterized by scanning electron microscopy. The results show that the strength of ACP initially increased (by 10–40 °C) and then later decreased (by 40–60 °C) with the increase in early curing temperature. ACP under 40 °C early curing exhibited the minimum number of cracks and mass loss after the tunnel fire. Too high or too low early curing temperature reduced the thermal conductivity of ACP but accelerated the formation and expansion of microcracks during the tunnel fire. The residual compressive strength of SCC coated with ACP under 40 °C early curing after the tunnel fire was the highest, demonstrating the best tunnel fire resistance.     

Preparation and Evaluation Mechanic Damping Properties of Fused Silica Powder@Polyurethane Urea/Cement Composites

In this paper, cement based on fused silica powder @ polyurethane urea (FSP@PUU) with a micro constrained damping structure was studied. Firstly, FSP@PUU core-shell particles were prepared by heterogeneous stepwise addition polymerization method and added into cement paste as damping filler to form a micro-constrained damping structure inside cement paste. The mechanical property and damping performance of cement-based composites were characterized by compressive strength, dynamic mechanical analysis (DMA) test and modal vibration test. The results showed that the damping performance of FSP @ PUU cement-based composites was affected by temperature, and the loss tangent of cement with 6wt% FSP@PUU increased to about 0.057 at −35 °C to 35 °C, which was 1.5 times cement paste within the glass transition temperature. With 6 wt% FSP@PUU, the damping ratio of cement-based composites increased by 58% compared with cement paste in the frequency range of 175–300 Hz, while the compressive strength decreased by only 5%. The cement with suitable FSP@PUU possesses excellent damping performance.     

Multiphase Model for Predicting the Thermal Conductivity of Cement Paste and Its Applications

Thermal conductivity plays a significant role in controlling thermal cracking of cement-based materials. In this study, the thermal conductivity of cement paste at an early age was measured by the hot plate method. The test results showed that the thermal conductivity of cement paste decreased with the increase of water/cement ratio and curing age. Meanwhile, a multiphase model for the thermal conductivity of cement paste was proposed and used to study the influence of saturation and curing temperature on the thermal conductivity of cement paste. To determine the parameters involved in this model, the thermal conductivity of each phase in cement paste was calculated by the molecular dynamic simulation method, and the hydration of cement was simulated by the Virtual Cement and Concrete Testing Laboratory. The inversion results showed that the relative error between experimental and simulation results lay between 1.1% and 6.5%. The thermal conductivity of paste in the saturated condition was 14.9–32.3% higher than that in the dry state. With the curing temperature increasing from 10 °C to 60 °C, the thermal conductivity of cement paste decreased by 3.9–4.9% depending on the water/cement ratio.     

Thermal Properties of Calcium Sulphoaluminate Cement as an Alternative to Ordinary Portland Cement

This paper presents the results of research into the heat of hydration and activation energy of calcium sulphoaluminate (CSA) cement in terms of the dependence on curing temperature and water/cement ratio. Cement pastes with water/cement ratios in the range of 0.3–0.6 were tested by isothermal calorimetry at 20 °C, 35 °C and 50 °C, with the evolved hydration heat and its rate monitored for 168 h from mixing water with cement. Reference pastes with ordinary Portland cement (OPC) were also tested in the same range. The apparent activation energy of CSA and OPC was determined based on the results of the measurements. CSA pastes exhibited complex thermal behaviour that differed significantly from the thermal behaviour of ordinary Portland cement. The results show that both the w/c ratio and elevated temperature have a meaningful effect on the heat emission and the hydration process of CSA cement pastes. The determined apparent activation energy of CSA revealed its substantial variability and dependence, both on the w/c ratio and the curing temperature.     

Evolution of Microstructural Characteristics of Carbonated Cement Pastes Subjected to High Temperatures Evaluated by MIP and SEM

The microstructural evolutions of both uncarbonated and carbonated cement pastes subjected to various high temperatures (30 °C, 200 °C, 400 °C, 500 °C, 600 °C, 720 °C, and 950 °C) are presented in this study by the means of mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM). It was found that the thermal stabilities of uncarbonated cement pastes were significantly changed from 400 to 500 °C due to the decomposition of portlandite at this temperature range. More large pores and microcracks were generated from 600 to 720 °C, with the depolymerization of C-S-H. After carbonation, the microstructures of carbonated cement pastes remained unchanged below 500 °C and started to degrade at 600 °C, due to the decompositions of calcium carbonates and calcium modified silica gel. At 950 °C, both uncarbonated and carbonated cement pastes showed a loosely honeycombed microstructure, composed mainly of β-C₂S and lime. It can be concluded that carbonation improves the high-temperature resistance of cement pastes up to 500 °C, but this advantage is lost at temperatures over 600 °C.     

Effect of Sulphur-Containing Tailings Content and Curing Temperature on the Properties of M32.5 Cement Mortar

The effect of the dosage of sulphur-containing tailings (STs) and curing temperature on the properties of M32.5 cement mortar was studied in this work. An experimental study was conducted to evaluate the effects of STs with different substitution ratios (0, 10%, 20%, 30%, 40%) on the compressive strength experiment, fluidity, expansion ratio, and pore structure of M32.5 cement mortar. The results showed that the addition of STs reduced the fluidity of mortar, and the fluidity decreased with the increase of the STs dosage. The compressive strength of mortars increased at a lower substitution rate (0~20%) but decreased at a higher substitution rate (>20%). Ettringite peaks and new sulfate peaks were found by X-ray diffraction (XRD) analysis. Scanning electron microscope (SEM) observation of the microstructure showed that a large number of hydrated products, such as ettringite, formed and filled in the interstitial space, which was conducive to the development of strength. The optimal STs replacement ratio of river sand was 10%. Then, the performance of mortar at curing temperatures of 23 ± 1, 40, 60, and 80 °C was further investigated under the optimal STs replacement ratio. Under high-temperature curing conditions, the early strength of M32.5 cement mortar with STs increased greatly, but the late strength decreased gradually with the increase in curing temperature. The early strength development of the mortar mainly depended on the high speed of hydration reaction, and the late strength variation was mainly affected by hydration products and the pore size distribution. After comprehensive consideration, the optimal curing temperature of M32.5 cement mortar with STs was 40 °C.     

Study on the Strength and Hydration Behavior of Sulfate-Resistant Cement in High Geothermal Environment

The hydration process and compressive strength and flexural strength development of sulphate-resistant Portland cement (SRPC) curing at 20 °C, 40 °C, 50 °C, and 60 °C were studied. In addition, MIP, XRD, SEM, and a thermodynamic simulation (using Gibbs Energy Minimization Software (GEMS)) were used to study the pore structure, the types, contents, and transformations of hydration products, and the changes in the internal micro-morphology. The results indicate that, compared with normal-temperature curing (20 °C), the early compressive strength (1, 3, and 7 d) of SRPC cured at 40~60 °C increased by 10.1~57.4%, and the flexural strength increased by 1.8~21.3%. However, high-temperature curing was unfavorable for the development of compressive strength and flexural strength in the later period (28~90 d), as they were reduced by 1.5~14.6% and 1.1~25.5%, respectively. With the increase in the curing temperature and curing age, the internal pores of the SRPC changed from small pores to large pores, and the number of harmful pores (>50 nm) increased significantly. In addition, the pore structure was further coarsened after curing at 60 °C for 90 d, and the number of multiple harmful pores (>200 nm) increased by 17.9%. High-temperature curing had no effect on the types of hydration products of the SRPC but accelerated the formation rate of hydration products. The production of the hydration products C-S-H increased by 13.5%, 18.6%, and 22.8% after curing at 40, 50, and 60 °C for 3 d, respectively. The stability of ettringite (AFt) reduced under high-temperature curing, and its diffraction peak was not observed in the XRD patterns. When the curing temperature was higher than 50 °C, AFt began to transform into monosulfate, which consumed more tricalcium aluminate hydrate and inhibited the formation of “delayed ettringite”. Under high-temperature curing, the compactness of the internal microstructure of the SRPC decreased, and the distribution of hydration products was not uniform, which affected the growth in its strength during the later period.     

Comparative Analysis of Strength and Deformation Behavior of Cemented Tailings Backfill under Curing Temperature Effect

Mineral resources are increasingly being developed in cold and permafrost regions. However, the mechanical and physical properties of cemented tailings backfill (CTB) cured at normal temperature are no longer applicable. To clarify the reasons for this variability, a series of tests were performed. The mechanical properties of CTB with different cement–tailings ratios (CTR, 1:4, 1:8, 1:12, 1:16, and 1:20) were tested at different curing ages (3, 7 and 28 days) and curing temperatures (20 °C, 5 °C, −5 °C, and −20 °C). The differences of CTB in mechanical and physical properties under positive- and negative-temperature curing conditions were analyzed, and the microscopic failure process of CTB under negative-temperature curing conditions was discussed. The results revealed that the mechanical properties and deformation behavior of CTB under positive- and negative-temperature curing conditions were different. The frozen CTB had higher early strength than the standard-temperature curing condition (20 °C), and the lower the temperature, the higher the early strength. The low-temperature curing condition, on the other hand, was not beneficial to CTB’s long-term strength. The low-temperature curing condition was not conducive to the long-term strength of CTB. After yielding, strain hardening and strain softening appeared in the deformation behavior of frozen backfill, indicating ductility. In contrast to the typical-temperature curing condition, the frozen CTB showed a new failure pattern that has little relation to curing time or CTR. Furthermore, the failure process of frozen backfill was reviewed and studied, which was separated into four stages, and altered as the curing time increased. The results of this study can act as a guide for filling mines in permafrost and cold climates.     

The Damage Performance of Uncarbonated Limestone Cement Pastes Partially Exposed to Na2SO4 Solution

Pore structure and composition of cement paste are the main two factors in controlling the sulfate attack on concrete, but the influence of carbonization on pore structure and composition is often ignored in sulfate attack. Therefore, will the damage performance of concrete partially exposed to sulfate solution be different avoiding the alterations of pore structure and composition due to carbonation? In this paper, the cement pastes were partially immersed in 5 wt. % sodium sulfate solution, with N₂ as protective gas to avoid carbonation (20 ± 1°C, RH 65 ± 5%). Pore structures of cements were changed by introducing different contents of limestone powders (0 wt. %, 10 wt. %, 20 wt. %, and 30 wt. %) into cement pastes. The damage performance of the specimens was studied by ¹H NMR, XRD and SEM. The results showed that the immersion zone of pure cement paste under N₂ atmosphere remained intact while serious damage occurred in the evaporation zone. However, the damage of cement + limestone powders pastes appeared in the immersion zone rather than in the evaporation zone and cement pastes containing more limestone were more severely damaged. Compositional analysis suggested that the damage of the evaporation zone or the immersion zone was solely caused by chemical attack where substantial amount of gypsums and ettringites were filled in the pore volumes. Introduction of limestone powders led to the increase of the pore sizes and porosity of cement pastes, causing the damage occurred in the immersion zone not in the evaporation zone.     

Properties of Blended Cement Containing Iron Tailing Powder at Different Curing Temperatures

The properties of blended cement containing 0%, 20%, and 50% iron tailing powder (ITP) at 20 °C and 60 °C were investigated by determining the hydration heat, microstructure, and compressive strength. The addition of ITP decreases the exothermic rate and cumulative hydration heat of blended cement at 20 °C. The high temperature increases the hydration rate and leads to the hydration heat of blended cement containing 20% ITP higher than that of Portland cement. Increasing the amount of ITP decreases the non-evaporable water content and Ca(OH)₂ content as well as compressive strength at both of the two studied temperatures. The addition of ITP coarsens the early-age pore structure but improves the later-age pore structure at 20 °C. The high temperature significantly improves the early-age properties of blended cement containing ITP, but it is detrimental to the later-age properties development. The reaction of ITP is limited even at high temperature. The large ITP particles bond poorly with surrounding hydration products under early high-temperature curing condition. The properties of blended cement containing a large amount of ITP are much poorer at high temperature.     

Investigation on Control Burned of Bagasse Ash on the Properties of Bagasse Ash-Blended Mortars

In recent years, partial replacement of cement with bagasse ash has been given attention for construction application due to its pozzolanic characteristics. Sugarcane bagasse ash and fine bagasse particles are abundant byproducts of the sugar industries and are disposed of in landfills. Our study presents the effect of burning bagasse at different temperatures (300 °C and 600 °C) on the compressive strength and physical properties of bagasse ash-blended mortars. Experimental results have revealed that bagasse produced more amorphous silica with very low carbon contents when it was burned at 600 °C/2 h. The compressive strength of mortar was improved when 5% bagasse ash replaced ordinary portland cement (OPC) at early curing ages. The addition of 10% bagasse ash cement also increased the compressive strength of mortars at 14 and 28 days of curing. However, none of the bagasse ash-blended portland pozzolana cement (PPC) mortars have shown improvement on compressive strength with the addition of bagasse ash. Characterization of bagasse ash was done using XRD, DTA-TGA, SEM, and atomic absorption spectrometry. Moreover, durability of mortars was checked by measuring water absorption and apparent porosity for bagasse ash-blended mortars.     

Experimental Research on Mechanical Properties of Carbon Fiber-Reinforced Reactive Powder Concrete after Exposure to Cryogenic Temperatures

This study aims to evaluate the mechanical properties of carbon fiber-reinforced reactive powder concrete (CFRPC) after exposure to cryogenic temperature. The mechanical properties of plain RPC and CFRPC with carbon fiber volume contents of 0, 0.5%, 1.0%, and 1.5% were examined after exposure to 20 °C, −5 °C, −15 °C, and −25 °C for 72 h. The effect of fiber contents and exposure temperatures on the cubic and axial compressive strength, splitting tensile strength, elastic modulus, and peak strain were systematically reported and analyzed. The results showed adding carbon fiber to RPC could significantly enhance the strength and slightly improve ductility performance. Additionally, CFRPC with 1.0% fiber content showed the best mechanical properties. The maximum increases in cubic and axial compressive strength and tensile strength were 26.0%, 25.7%, and 21.8%, the elastic modulus was 13.2%, and the peak strain was 13.0% over the plain RPC. Additionally, all mechanical properties continued to degrade with decreasing temperature. After exposure to −25 °C, the cubic, axial compressive strength, and tensile strength of CFRPC degraded to 82.2–84.9%, 80.7–87.5%, and 72.7–73.7% of the normal temperature strength, respectively. In addition, the linear relationship equation between the discount factor of each mechanical property and the temperature was established. Finally, the equation for the stress–strain ascending curve of CFRPC described by a quadratic polynomial was proposed, which fitted well with the experimental results.     

Chemical and Microstructural Properties of Designed Cohesive M-S-H Pastes

Concretes can be exposed to a magnesium attack in several environments leading to the formation of magnesium silicate hydrates (M-S-H) and brucite (MH). The formation of M-S-H is likely to alter the properties of the cement matrix because it is linked to the decalcification of C-S-H. However, relatively few data on M-S-H exist in the literature. In order to characterize, physically and mechanically, the M-S-H phase, pure M-S-H cohesive pastes are needed. This work studies the formation of cohesive M-S-H pastes made with MgO-to-SiO₂ atomic ratios of 0.78, 1 and 1.3, from two types of silica (silica fume or colloidal silica) and under 20 °C and 50 °C thermal curing. X-ray diffraction and thermogravimetric analyses confirmed that the consumption of brucite and the formation of M-S-H were quicker with a 50 °C curing. Energy-dispersive X-ray spectroscopy and microtomography showed that colloidal silica enabled a better distribution of the particles than silica fume. Microstructural characterizations were conducted under the protocol with colloidal silica and 50 °C thermal curing. Porosity investigations allowed to describe the M-S-H pastes as highly porous materials with a low content of micropores in comparison with mesopores. The type of mixing influenced the mesopore size distribution.     

The Effects of Temperature Curing on the Strength Development,Transport Properties,and Freeze-Thaw Resistance of Blast Furnace Slag Cement Mortars Modified with Nanosilica

This investigation studies the effects of hot water and hot air curing on the strength development, transport properties, and freeze-thaw resistance of mortars incorporating low-heat blast furnace slag cement and nanosilica (NS). Mortar samples were prepared and stored in ambient conditions for 24 h. After demolding, mortar samples were subjected to two different hot curing methods: Hot water and hot air curing (40 °C and 60 °C) for 24 h. For comparison purposes, mortar reference mixes were prepared and cured in water and air at ambient conditions. Strength development (from 1 to 180 days), capillary water porosity, water sorptivity, and freeze-thaw resistance were tested after 180 days of curing. The experimental results showed that both curing regimes accelerate the strength development of mortars, especially in the first seven days of hydration. The highest early strengths were reported for mortars subjected to a temperature of 60 °C, followed by those cured at 40 °C. The hot water curing regime was found to be more suitable, as a result of more stable strength development. Similar findings were observed in regard to durability-related properties. It is worth noting that thermal curing can more efficiently increase strength in the presence of nanosilica, suggesting that NS is more effective in enhancing strength under thermal curing.     

Evaluating the Feasibility of Using Brick Powder and Clay Powder in Cement Replacement

The cement industry generates very large amounts of CO₂ into the atmosphere. In recent years, there has been a search for alternative cementitious materials and micro-fillers that could partially or fully replace cement in cement composites without compromising their durability. This paper investigates the possibility of using brick powder (BP) and clay powder (CP) as a partial replacement for cement (up to 20% by weight) in cement paste. The raw materials were characterized, and the physical and mechanical properties of the modified cement pastes were studied, as well as their resistance to a short-term thermal shock at 250 °C. The study was supplemented by intelligent modelling of compressive strength using the support vector machine (SVM) algorithms. The results indicated a significant increase in tensile strength (up to 100%) and an increase in thermal resistance of cement pastes modified with BP and CP. The proposed SVM model had high accuracy (R² = 0.90), indicating its suitability to predict the compressive strength of the modified cement matrix. This study complements the knowledge in the field of inter alia, the effect of a short-term thermal shock at elevated temperature on the properties of BP and CP modified cement paste, and the effect of BP, which, due to its grain size, plays more the role of a microfiller than a pozzolanic additive.     

Properties and Microstructures of Crushed Rock Based-Alkaline Activated Material for Roadway Applications

The worldwide demand for roads to serve global economic growth has led to the increasing popularity of road improvement using cement. This, in turn, has led to increased demand for cement and the associated problem of CO₂ emissions. Alkaline-activated materials (AAMs) could be an alternative binder for relatively low strength construction and rehabilitation as a cement replacement material. Compared to other applications, the lower strength requirements of road construction materials could ease any difficulties with AAM production. In this study, crushed rock (CR) was used as a prime raw material. The mechanisms and microstructures of the hardened AAM were investigated along with its mechanical properties. The results showed that CR-based AAM with an optimum mixture of 5 M of NaOH concentration, an SS/SH ratio of 1.00, and a liquid alkaline-to-binder (L/B) ratio of 0.5 could be used for roadway applications. At this ratio, the paste samples cured at room temperature (26 ± 3 °C) had an early compressive strength (3 days-age) of 3.82 MPa, while the paste samples cured at 60 °C had an early compressive strength of 6.45 MPa. The targeted strength results were able to be applied to a cement-treated base (CTB) for pavement and roadway applications (2.1 to 5.5 MPa).     

Accelerated Curing for Glass-Based Mortars Using Water at 80 °C

The substitution of river sand with glass aggregate (GA) and cement with glass powder (GP) is a mainstream method to recycle waste glass. Traditionally, standard curing was widely used for glass-based mortars. However, it is time-consuming and cannot address low mechanical strengths of the early-age mortars. Therefore, the effect of water curing at 80 °C on the properties of GA mortars is investigated. Furthermore, the effect of the GP size is also considered. Results show that compared with the expansion of alkali-silica reaction (ASR), water curing at 80 °C has a negligible effect on the volume change. Moreover, the compressive strength of GA mortars under 1-day water curing at 80 °C is comparable with that under 28-day water curing at 20 °C. Therefore, the 1-day water curing at 80 °C is proposed as an accelerated curing method for GA mortars. On the other hand, the addition of GP with the mean size of 28.3 and 47.9 μm can effectively mitigate the ASR expansion of GA mortars. Compared with the size of 28.3 μm, GA mortars containing GP (47.9 μm) always obtain higher compressive strength. In particular, when applying the 1-day water curing at 80 °C, GA mortars containing GP (47.9 μm) can even gain higher strength than those containing fly ash.     

Phosphate Cements Based on Calcined Dolomite: Influence of Calcination Temperature and Silica Addition

The aim of this study is to assess the possibility of obtaining phosphate cements based on dolomite calcined at various temperatures with/without quartz sand addition. A lower calcination temperature of dolomite (1200 °C) determines a high increase in the system temperature when calcined dolomite is mixed with KH₂PO₄ (MKP) solution and also a rapid expansion of the paste. The increase in calcination temperature up to 1400 °C reduces the oxides reactivity; however, for lower dosages of MKP, the expansion phenomenon is still recorded. The increase in MKP dosage increases the compressive strength due to the formation of K-struvite. The mixing of dolomite with sand, followed by thermal treatment at 1200 °C, modifies its composition and reactivity; the compressive strength of phosphate cements obtained by mixing this solid precursor with MKP increases up to 28 days of curing. We assessed the nature of hydrates formed in the phosphate systems studied by X-ray diffraction in order to explain the hardening processes and the mechanical properties of these systems. The microstructure and elemental composition of hardened cement pastes were assessed by scanning electronic microscopy with energy-dispersive spectroscopy. The phosphate cements based on calcined magnesite or dolomite were used to immobilize an industrial hazardous waste with high chromium content. The partial substitution of calcined magnesite/dolomite with this waste determines an important decrease in compressive strengths. Nevertheless, the leaching tests confirm an adequate immobilization of chromium in some of the matrices studied (for a waste dosage corresponding to 0.5 wt % Cr).