Microstructural Improvement of Eutectic Al + Mg2Si Phases on Al–Zn–Si–Mg Cast Alloy with TiB2 Particles Additions

In this study, the effects of adding TiB₂ particles to eutectic Al + Mg₂Si phases in aluminum alloys were analyzed. The eutectic Al + Mg₂Si phases were modified effectively when a large amount of TiB₂ was added, and changes in the shape, size, and distribution of the eutectic Al + Mg₂Si phases were confirmed using a polarizing microscope and FE-SEM. The crystal structure of the TiB₂ particles and Mg₂Si phases were analyzed using HR-TEM, and the analysis confirmed that the TiB₂ particles can act as heterogeneous nucleation sites. This paper intends to clarify the principle of phase modification of the eutectic Al + Mg₂Si phases by TiB₂ particles and proposes a new mechanism to improve Mg₂Si phase modification when TiB₂ particles are added.     

Characterization of Al2O3 Samples and NiAl–Al2O3 Composite Consolidated by Pulse Plasma Sintering

The paper describes an investigation of Al₂O₃ samples and NiAl–Al₂O₃ composites consolidated by pulse plasma sintering (PPS). In the experiment, several methods were used to determine the properties and microstructure of the raw Al₂O₃ powder, NiAl–Al₂O₃ powder after mechanical alloying, and samples obtained via the PPS. The microstructural investigation of the alumina and composite properties involves scanning electron microscopy (SEM) analysis and X-ray diffraction (XRD). The relative densities were investigated with helium pycnometer and Archimedes method measurements. Microhardness analysis with fracture toughness (K_IC) measures was applied to estimate the mechanical properties of the investigated materials. Using the PPS technique allows the production of bulk Al₂O₃ samples and intermetallic ceramic composites from the NiAl–Al₂O₃ system. To produce by PPS method the NiAl–Al₂O₃ bulk materials initially, the composite powder NiAl–Al₂O₃ was obtained by mechanical alloying. As initial powders, Ni, Al, and Al₂O₃ were used. After the PPS process, the final composite materials consist of two phases: Al₂O₃ located within the NiAl matrix. The intermetallic ceramic composites have relative densities: for composites with 10 wt.% Al₂O₃ 97.9% and samples containing 20 wt.% Al₂O₃ close to 100%. The hardness of both composites is equal to 5.8 GPa. Moreover, after PPS consolidation, NiAl–Al₂O₃ composites were characterized by high plasticity. The presented results are promising for the subsequent study of consolidation composite NiAl–Al₂O₃ powder with various initial contributions of ceramics (Al₂O₃) and a mixture of intermetallic–ceramic composite powders with the addition of ceramics to fabricate composites with complex microstructures and properties. In composites with complex microstructures that belong to the new class of composites, in particular, the synergistic effect of various mechanisms of improving the fracture toughness will be operated.     

The Reaction Products of the Al–Nb–B2O3–CuO System in an Al 6063 Alloy Melt and Their Influence on the Alloy’s Structure and Characteristics

To meet aero-engine aluminum skirt requirements, an experiment was carried out using Al–Nb–B₂O₃–CuO as the reaction system and a 6063 aluminum alloy melt as the reaction medium for a contact reaction, and 6063 aluminum matrix composites containing in situ particles were prepared with the near-liquid-phase line-casting method after the reaction was completed. The effects of the reactant molar ratio and the preheating temperature on the in situ reaction process and products were explored in order to determine the influence of in situ-reaction-product features on the organization and the qualities of the composites. Thermodynamic calculations, DSC analysis, and experiments revealed that the reaction could continue when the molar ratio of the reactants of Al–Nb–B₂O₃–CuO was 6:1:1:1.5. A kinetic study revealed that the Al thermal reaction in the system produced Al₂O₃ and [B], and the [B] atoms interacted with Nb to generate NbB₂. With increasing temperature, the interaction between the Nb and the AlB₂ produced hexagonal NbB₂ particles with an average longitudinal size of 1 μm and subspherical Al₂O₃ particles with an average longitudinal size of 0.2 μm. The microstructure of the composites was reasonably fine, with an estimated equiaxed crystal size of around 22 μm, a tensile strength of 170 MPa, a yield strength of 135 MPa, an elongation of 13.4%, and a fracture energy of 17.05 × 10⁵ KJ/m³, with a content of 2.3 wt% complex-phase particles. When compared to the matrix alloy without addition, the NbB₂ and Al₂O₃ particles produced by the in situ reaction had a significant refinement effect on the microstructure of the alloy, and the plasticity of the composite in the as-cast state was improved while maintaining higher strength and better overall mechanical properties, allowing for industrial mass production.     

Heat Treatment-Induced Microstructure and Property Evolution of Mg/Al Intermetallic Compound Coatings Prepared by Al Electrodeposition on Mg Alloy from Molten Salt Electrolytes

A method of forming an Mg/Al intermetallic compound coating enriched with Mg₁₇Al₁₂ and Mg₂Al₃ was developed by heat treatment of electrodeposition Al coatings on Mg alloy at 350 °C. The composition of the Mg/Al intermetallic compounds could be tuned by changing the thickness of the Zn immersion layer. The morphology and composition of the Mg/Al intermetallic compound coatings were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), and electron backscattered diffraction (EBSD). Nanomechanical properties were investigated via nano-hardness (nHV) and the elastic modulus (EIT), and the corrosion behavior was studied through hydrogen evolution and potentiodynamic (PD) polarization. The compact and uniform Al coating was electrodeposited on the Zn-immersed AZ91D substrate. After heat treatment, Mg₂Al₃ and Mg₁₇Al₁₂ phases formed, and as the thickness of the Zn layer increased from 0.2 to 1.8 μm, the ratio of Mg₂Al₃ and Mg₁₇Al₁₂ varied from 1:1 to 4:1. The nano-hardness increased to 2.4 ± 0.5 GPa and further improved to 3.5 ± 0.1 GPa. The Mg/Al intermetallic compound coating exhibited excellent corrosion resistance and had a prominent effect on the protection of the Mg alloy matrix. The control over the ratio of intermetallic compounds by varying the thickness of the Zn immersion layer can be an effective approach to achieve the optimal comprehensive performance. As the Zn immersion time was 4 min, the obtained intermetallic compounds had relatively excellent comprehensive properties.     

Effect of Al2Ca Addition and Heat Treatment on the Microstructure Modification and Tensile Properties of Hypo-Eutectic Al–Mg–Si Alloys

The current study investigated the microstructure modification in Al–6Mg–5Si–0.15Ti alloy (in mass %) through the minor addition of Ca using Mg + Al₂Ca master alloy and heat treatment to see their impact on mechanical properties. The microstructure of unmodified alloy (without Ca) consisted of primary Al, primary Mg₂Si, binary eutectic Al–Mg₂Si, ternary eutectic Al–Mg₂Si–Si, and iron-bearing phases. The addition of 0.05 wt% Ca resulted in significant microstructure refinement. In addition to refinement, lamellar to fibrous-type modification of binary eutectic Al–Mg₂Si phases was also achieved in Ca-added (modified) alloy. This modification was related to increasing Ca-based intermetallics/compounds in the modified alloy that acted as nucleation sites for binary eutectic Al–Mg₂Si phases. The dendritic refinement with Ca addition was related to the fact that it improves the efficacy of Ti-based particles (TiAl₃ and TiB₂) in the melt to act as nucleation sites. In contrast, the occupation of oxide bifilms by Ca-based phases is expected to force the iron-bearing phases (as iron-bearing phases nucleate at oxide films) to solidify at lower temperatures, thus reducing their size. The as-cast microstructure of these alloys was further modified by subjecting them to solution treatment at 540 °C for 6 h, which broke the eutectic structure and redistributed Mg₂Si and Si phases in Al-matrix. Subsequent aging treatment caused a dramatic increase in the tensile strength of these alloys, and tensile strength of 291 MPa (with El% of 0.45%) and 327 MPa (with El% of 0.76%) was achieved for the unmodified alloy and modified alloy, respectively. Higher tensile strength and elongation of the modified alloy than unmodified alloy was attributed to refined dendritic structure and modified second phases.     

Functionally Graded Al2O3–CTZ Ceramics Fabricated by Spark Plasma Sintering

We studied the fabrication of functionally graded Al₂O₃–CeO₂-stabilized-ZrO₂ (CTZ) ceramics by spark plasma sintering. The ceramic composite exhibits a gradual change in terms of composition and porosity in the axial direction. The composition gradient was created by layering starting powders with different Al₂O₃ to CTZ ratios, whereas the porosity gradient was established with a large temperature difference, which was induced by an asymmetric graphite tool configuration during sintering. SEM investigations confirmed the development of a porosity gradient from the top toward the bottom side of the Al₂O₃–CTZ ceramic and the relative pore volume distributed in a wide range from 0.02 to 100 µm for the samples sintered in asymmetric configuration (ASY), while for the reference samples (STD), the size of pores was limited in the nanometer scale. The microhardness test exhibited a gradual change along the axis of the ASY samples, reaching 10 GPa difference between the two opposite sides of the Al₂O₃–CTZ ceramics without any sign of delamination or cracks between the layers. The flexural strength of the samples for both series showed an increasing tendency with higher sintering temperatures. However, the ASY samples achieved higher strength due to their lower total porosity and the newly formed elongated CeAl₁₁O₁₈ particles.     

Effect of Al2TiO5 Content and Sintering Temperature on the Microstructure and Residual Stress of Al2O3–Al2TiO5 Ceramic Composites

A series of Al₂O₃–Al₂TiO₅ ceramic composites with different Al₂TiO₅ contents (10 and 40 vol.%) fabricated at different sintering temperatures (1450 and 1550 °C) was studied in the present work. The microstructure, crystallite structure, and through-thickness residual stress of these composites were investigated by scanning electron microscopy, X-ray diffraction, time-of-flight neutron diffraction, and Rietveld analysis. Lattice parameter variations and individual peak shifts were analyzed to calculate the mean phase stresses in the Al₂O₃ matrix and Al₂TiO₅ particulates as well as the peak-specific residual stresses for different hkl reflections of each phase. The results showed that the microstructure of the composites was affected by the Al₂TiO₅ content and sintering temperature. Moreover, as the Al₂TiO₅ grain size increased, microcracking occurred, resulting in decreased flexure strength. The sintering temperatures at 1450 and 1550 °C ensured the complete formation of Al₂TiO₅ during the reaction sintering and the subsequent cooling of Al₂O₃–Al₂TiO₅ composites. Some decomposition of AT occurred at the sintering temperature of 1550 °C. The mean phase residual stresses in Al₂TiO₅ particulates are tensile, and those in the Al₂O₃ matrix are compressive, with virtually flat through-thickness residual stress profiles in bulk samples. Owing to the thermal expansion anisotropy in the individual phase, the sign and magnitude of peak-specific residual stress values highly depend on individual hkl reflection. Both mean phase and peak-specific residual stresses were found to be dependent on the Al₂TiO₅ content and sintering temperature of Al₂O₃–Al₂TiO₅ composites, since the different developed microstructures can produce stress-relief microcracks. The present work is beneficial for developing Al₂O₃–Al₂TiO₅ composites with controlled microstructure and residual stress, which are crucial for achieving the desired thermal and mechanical properties.     

The Formation of 14H-LPSO in Mg–9Gd–2Y–2Zn–0.5Zr Alloy during Heat Treatment

There is a new long-period stacking ordered structure in Mg–RE–Zn magnesium alloys, namely the LPSO phase, which can effectively improve the yield strength, elongation, and corrosion resistance of Mg alloys. According to different types of Mg–RE–Zn alloy systems, two transformation modes are involved in the heat treatment transformation process. The first is the alloy without LPSO phase in the as-cast alloy, and the Mg_xRE phase changes to 14H-LPSO phase. The second is the alloy containing LPSO phase in the as-cast state, and the 14H-LPSO phase is obtained by the transformations of 6H, 18R, and 24R. The effects of different solution parameters on the second phase of Mg–9Gd–2Y–2Zn–0.5Zr alloy were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The precipitation mechanism of 14H-LPSO phase during solution treatment was further clarified. At a solution time of 13 h, the grain size increased rapidly initially and then decreased slightly with increasing solution temperature. The analysis of the volume fraction of the second phase and lattice constant showed that Gd and Y elements in the alloy precipitated from the matrix and formed 14H-LPSO phase after solution treatment at 490 °C for 13 h. At this time, the hardness of the alloy reached the maximum of 74.6 HV. After solution treatment at 500 °C for 13 h, the solid solution degree of the alloy increases, and the grain size and hardness of the alloy remain basically unchanged.     

Calculation Based on the Formation of Mg2Si and Its Effect on the Microstructure and Properties of Al–Si Alloys

In order to investigate the effect of Mg₂Si formation on the microstructure and properties of an Al−Si alloy, the critical point of a hypereutectic Al−17Si−4Cu−Mg alloy was calculated by Pandat software. The calculation results of the equilibrium phase diagram show that the critical point for Mg₂Si phase formation for the alloy was obtained when the Mg content was 2.2%. The contents of 0.5 wt.% Mg and 2.5 wt.% Mg were selected as the research object. The content of Mg increased from 0.5 wt.% to 2.5 wt.%, the eutectic Si in the matrix was reduced, and the Chinese character-like Mg₂Si phase appeared in the microstructure. In the peak ageing state, in addition to θ″ and Q′ phases that were mainly precipitated, there was also needle-like β″ precipitation in the 2.5 wt.% Mg content alloy. Larger precipitates were found in 2.5 wt.% content alloys, mainly due to the promotion of the solid solution having the aggregation and segregation of more solute elements in the matrix. The tensile strength, elongation, and hardness of hypereutectic Al−17Si−4Cu−0.5Mg alloy under peak ageing were 331 MPa, 3.11%, and 152.1 HB, respectively. The tensile strength and the elongation decreased while the hardness increased with the 2.5 wt.% Mg content, which is due to the formation of hard and brittle Mg₂Si and Al₈FeMg₃Si, which has a splitting effect on the matrix.     

Al2O3/ZrO2/Y3Al5O12 Composites: A High-Temperature Mechanical Characterization

An Al₂O₃/5 vol%·ZrO₂/5 vol%·Y₃Al₅O₁₂ (YAG) tri-phase composite was manufactured by surface modification of an alumina powder with inorganic precursors of the second phases. The bulk materials were produced by die-pressing and pressureless sintering at 1500 °C, obtaining fully dense, homogenous samples, with ultra-fine ZrO₂ and YAG grains dispersed in a sub-micronic alumina matrix. The high temperature mechanical properties were investigated by four-point bending tests up to 1500 °C, and the grain size stability was assessed by observing the microstructural evolution of the samples heat treated up to 1700 °C. Dynamic indentation measures were performed on as-sintered and heat-treated Al₂O₃/ZrO₂/YAG samples in order to evaluate the micro-hardness and elastic modulus as a function of re-heating temperature. The high temperature bending tests highlighted a transition from brittle to plastic behavior comprised between 1350 and 1400 °C and a considerable flexural strength reduction at temperatures higher than 1400 °C; moreover, the microstructural investigations carried out on the re-heated samples showed a very limited grain growth up to 1650 °C.     

Plasma Oscillatory Pressure Sintering of Mo-9Si-8B Alloy with ZrB2 Addition

Oscillatory pressure sintering is a novel crystal refinement technology. The doping of different concentrations of ZrB₂ under oscillatory sintering technology (9 Hz) is discussed here, focusing on its macroscopic mechanics and oxidation resistance. In particular, doping 2.5 wt% ZrB₂ can effectively increase the hardness of the alloy, slightly increase the fracture toughness of the alloy and have an outstanding effect on the oxidation resistance of the alloy at 1300 °C, achieving the effect of reducing mass loss by 80.3%.     

Heat Treatment of Cast and Cold Rolled Al–Yb and Al–Mn–Yb–Zr Alloys

The microstructure, electrical properties and microhardness of as-cast and cold rolled AlYb and AlMnYbZr alloys were investigated. The addition of Mn, Yb and Zr has a positive influence on grain size. A deformed structure of the grains with no changes of their size was observed after cold rolling. The Al₃Yb particles coherent with the matrix were observed in the AlYb alloys. The size of the particles was about 20 nm in the initial state; after isochronal treatment up to 540 °C the particles coarsen, and their number density was lower. The deformation has a massive effect on the microhardness behavior until treatment at 390 °C, after which the difference in microhardness changes between as-cast and cold rolled alloys disappeared. Relative resistivity changes show a large decrease in the temperature interval of 330–540 °C which is probably caused by a combination of recovery of dislocations and precipitation of the Al₃(Yb,Zr) particles. Precipitation hardening was observed between 100 and 450 °C in the AlYb alloy after ageing at 625 °C/24 h and between 330 and 570 °C in the AlMnYbZr alloy after ageing at 625 °C/24 h.     

Enhanced Hydrogen Storage Kinetics of Nanocrystalline and Amorphous Mg2Ni-type Alloy by Melt Spinning

Mg₂Ni-type Mg₂Ni_1−xCo_x (x = 0, 0.1, 0.2, 0.3, 0.4) alloys were fabricated by melt spinning technique. The structures of the as-spun alloys were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The hydrogen absorption and desorption kinetics of the alloys were measured by an automatically controlled Sieverts apparatus. The electrochemical hydrogen storage kinetics of the as-spun alloys was tested by an automatic galvanostatic system. The results show that the as-spun (x = 0.1) alloy exhibits a typical nanocrystalline structure, while the as-spun (x = 0.4) alloy displays a nanocrystalline and amorphous structure, confirming that the substitution of Co for Ni notably intensifies the glass forming ability of the Mg₂Ni-type alloy. The melt spinning treatment notably improves the hydriding and dehydriding kinetics as well as the high rate discharge ability (HRD) of the alloys. With an increase in the spinning rate from 0 (as-cast is defined as spinning rate of 0 m/s) to 30 m/s, the hydrogen absorption saturation ratio (R5a) of the (x = 0.4) alloy increases from 77.1 to 93.5%, the hydrogen desorption ratio (R20d) from 54.5 to 70.2%, the hydrogen diffusion coefficient (D) from 0.75 × 10⁻¹¹ to 3.88 × 10⁻¹¹ cm²/s and the limiting current density I_L from 150.9 to 887.4 mA/g.     

Study on Electromagnetic Performance of La0.5Sr0.5CoO3/Al2O3 Ceramic with Metal Periodic Structure at X-Band

A radar absorbing material (RAM) is designed by combining the La_0.5Sr_0.5CoO₃/Al₂O₃ ceramic and the metal periodic structure. The phase constitution and the microscopic morphology of the La_0.5Sr_0.5CoO₃/Al₂O₃ ceramic are examined, respectively. The electrical properties and magnetic properties of the La_0.5Sr_0.5CoO₃/Al₂O₃ ceramic are also measured at the temperature range of 25~500 °C. Based on the experimental and simulation results, the changes in the reflection loss along with the structure parameters of RAM are analyzed at 500 °C. The analytical results show that the absorption property of the RAM increases with the increase in the temperature. When the thickness of the La_0.5Sr_0.5CoO₃/Al₂O₃ ceramic is 1.5 mm, a reflection loss <−10 dB can be obtained in the frequency range from approximately 8.2 to 16 GHz. More than 90% microwave energy can be consumed in the RAM, which may be applied in the high temperature environment.     

The Effect of (Mg,Zn)12Ce Phase Content on the Microstructure and the Mechanical Properties of Mg–Zn–Ce–Zr Alloy

The quantitative study of rare earth compounds is important for the improvement of existing magnesium alloy systems and the design of new magnesium alloys. In this paper, the effective separation of matrix and compound in Mg–Zn–Ce–Zr alloy was achieved by a low-temperature chemical phase separation technique. The mass fraction of the (Mg, Zn)₁₂Ce compound was determined and the effect of the (Mg, Zn)₁₂Ce phase content on the heat deformation organization and properties was investigated. The results show that the Mg–Zn–Ce compound in both the as-cast and the homogeneous alloys is (Mg, Zn)₁₂Ce. (Mg, Zn)₁₂Ce phase formation depends on the content and the ratio of Zn and Ce elements in the initial residual melt of the eutectic reaction. The Zn/Ce mass ratios below 2.5 give the highest compound contents for different Zn contents, 5.262 wt.% and 7.040 wt.%, respectively. The increase in the amount of the (Mg, Zn)₁₂Ce phase can significantly reduce the critical conditions for dynamic recrystallization formation. Both the critical strain and the stress decrease with increasing rare earth content. The reduction of the critical conditions and the particle-promoted nucleation mechanism work together to increase the amount of dynamic recrystallization. In addition, it was found that alloys with 6 wt.% Zn elements tend to undergo a dynamic recrystallization softening mechanism, while alloys with 3 wt.% Zn elements tend to undergo a dynamic reversion softening mechanism.     

Synthesis and Characterization of LaNi0.5Ti0.5O3 and La2NiTiO6 Double Perovskite Nanoparticles

In the present work, LaNi_0.5Ti_0.5O₃ and La₂NiTiO₆ nanoparticles were synthesized by the modified Pechini method. LaNi_0.5Ti_0.5O₃ was calcined at 1073 K for 17 h or 100 h, while La₂NiTiO₆ was calcined at 1273 K for 135 h. The double perovskite calcined at 1073 K for 17 h presented orthorhombic symmetry with Pbnm space group, mean particle size was 31.9 ± 1 nm, random ordering of Ni²⁺ and Ti⁴⁺ cations, Néel temperature close to 15 K, and magnetic moment of 1.29 μB. By increasing the calcination time, this material showed the same symmetry and space group, a mean particle size of 50.7 ± 2 nm, short-range ordering of Ni²⁺ and Ti⁴⁺ cations, Néel temperature around 12 K, and magnetic moment of 0.96 μB. La₂NiTiO₆ presented a monoclinic crystal structure, with P2₁/n space group, mean particle size of 80.0 ± 5 nm, rock salt ordering of Ni²⁺ and Ti⁴⁺, Néel temperature of approximately 23 K, and magnetic moment of 2.75 μB.     

Corrosion Behavior of an Mg2Sn Alloy

In the present work, the corrosion behavior of the Mg₂Sn alloy (Mg_66.7Sn_33.3, concentration in at.%) has been studied. The alloy was prepared from high purity Sn and Mg lumps by induction melting in argon. The alloy was composed of intermetallic Mg₂Sn with a small amount of Mg₂Sn + (Sn) eutectic. The corrosion behavior was studied by hydrogen evolution, immersion, and potentiodynamic experiments. Three aqueous solutions of NaCl (3.5 wt.%), NaOH (0.1 wt.%) and HCl (0.1 wt.%) were chosen as corrosion media. The alloy was found to be cathodic with respect to metallic Mg and anodic with respect to Sn. The corrosion potentials of the Mg₂Sn alloy were −1380, −1498 and −1361 mV vs. sat. Ag/AgCl in HCl, NaCl and NaOH solutions, respectively. The highest corrosion rate of the alloy, 92 mmpy, was found in aqueous HCl. The high corrosion rate was accompanied by massive hydrogen evolution on the alloy’s surface. The corrosion rate was found to decrease sharply with increasing pH of the electrolyte. In the NaOH electrolyte, a passivation of the alloy was observed. The corrosion of the alloy involved a simultaneous oxidation of Mg and Sn. The main corrosion products on the alloy surface were MgSn(OH)₆ and Mg(OH)₂. The corrosion mechanism is discussed and implications for practical applications of the alloy are provided.     

Morphological Evolution of TiB2 and TiAl3 in Al–Ti–B Master Alloy Using Different Ti Adding Routes

Three different Ti addition routes were used to prepare an Al–5Ti–B Master Alloy: the halide salt route, the Ti-sponge route, and the partial Ti-sponge route. In the halide salt route, the raw materials were Al + KBF₄ + K₂TiF₆; K₂TiF₆ was completely replaced by pure titanium for the Ti-sponge route versus the halide salt route; in the partial Ti-sponge route, K₂TiF₆ was partially replaced by pure titanium. Here, 30% Ti-sponge or 60% Ti-sponge route means that 30% or 60% K₂TiF₆ was replaced by pure titanium, respectively. The above Ti addition routes have a significant influence on the growth pattern and morphological evolution of TiAl₃ and TiB₂, which greatly affect the refining performance of Al–Ti–B Master Alloy. When using the halide salt route, a streamlined “rich Ti, B area” exists in the aluminum melt, which is a complex compound of (Ti_x, Al_1−x) B_y. The “rich Ti, B area” is essential for the nucleation and growth of TiAl₃ and TiB₂. Blocky TiAl₃ was obtained and its average size was 4.7 μm based on the halide salt route. In the Ti-sponge route, the nucleation of TiAl₃ mainly depends on the mutual diffusion of Al and Ti, and TiAl_x forms around pure Ti particles, i.e., the so-called Ti–TiAl_x mechanism. The average size of the blocky TiAl₃ was 9.8 μm based on the Ti–TiAl_x mechanism. For the partial Ti-sponge route, the “rich Ti, B area” gradually decreases with the increase in Ti powder’s contents, and large TiAl₃ coexists with the small TiAl₃. Compared with the Ti-sponge route, the halide salt route can form smaller TiAl₃. In the Ti-sponge route, there is a small amount of “rich Ti, B area” due to the influence of the Ti–TiAl_x mechanism, which does not meet the requirements of TiB₂ growth. In the halide salt route, there is sufficient “rich Ti, B area”, which is conducive to the formation of TiB₂. Both the crystal defects and the crowded growth environment caused by the “rich Ti, B area” are fundamental reasons for the fragility and the irregular shape of the TiB₂. The refining effect of the Al–Ti–B Master Alloy prepared by the halide salt route is better than the Ti-sponge route. The refining effect of 30% Ti-sponge route is better than that of Ti-sponge route and worse than that of halide salt route.     

Study on Crystallization Process of Li2O–Al2O3–SiO2 Glass-Ceramics Based on In Situ Analysis

In this paper, we used differential scanning calorimetry (DSC), high-temperature X-ray diffraction (HT-XRD), and confocal scanning laser microscopy (CSLM) to investigate the Li₂O–Al₂O_3–SiO₂ glass crystallization process. At 943 K, lithium disilicate (Li₂Si₂O₅) phase crystals began to precipitate in the Li₂O–Al₂O₃–SiO₂ glass with a crystal size of 50–70 nm. At the temperature of 1009 K, petalite (LiAlSi₄O₁₀) crystals began to precipitate in the vitreous phase, forming composite spherical crystals of LiAlSi₄O₁₀ and Li₂Si₂O₅ with size in the range of 90–130 nm. Furthermore, the Kissinger method and KAS method of the JMAK model were used to calculate the crystallization activation energy and the Avrami index “n”. It was found that the precipitation mechanism of the two kinds of crystals is whole crystallization; accordingly, the selection of crystallization heat treatment system was guided to determine the nucleation and crystallization temperature.     

Sintering Behavior,Thermal Expansion,and Environmental Impacts Accompanying Materials of the Al2O3/ZrO2 System Fabricated via Slip Casting

This work focuses on research on obtaining and characterizing Al₂O₃/ZrO₂ materials formed via slip casting method. The main emphasis in the research was placed on environmental aspects and those related to the practical use of ceramic materials. The goal was to analyze the environmental loads associated with the manufacturing of Al₂O₃/ZrO₂ composites, as well as to determine the coefficient of thermal expansion of the obtained materials, classified as technical ceramics. This parameter is crucial in terms of their practical applications in high-temperature working conditions, e.g., as parts of industrial machines. The study reports on the four series of Al₂O₃/ZrO₂ materials differing in the volume content of ZrO₂. The sintering process was preceded by thermogravimetric measurements. The fabricated and sintered materials were characterized by dilatometric study, scanning electron microscopy, X-ray diffraction, and stereological analysis. Further, life cycle assessment was supplied. Based on dilatometric tests, it was observed that Al₂O₃/ZrO₂ composites show a higher coefficient of thermal expansion than that resulting from the content of individual phases. The results of the life cycle analysis showed that the environmental loads (carbon footprint) resulting from the acquisition and processing of raw materials necessary for the production of sinters from Al₂O₃ and ZrO₂ are comparable to those associated with the production of plastic products such as polypropylene or polyvinyl chloride.