Debris,Roughness and Friction of Stainless Steel Archwires Following Clinical Use

Objective:To investigate the degree of debris, roughness, and friction of stainless steel orthodontic archwires before and after clinical use.Materials and Methods:For eight individuals, two sets of three brackets (n  =  16) each were bonded from the first molar to the first premolar. A passive segment of 0.019- × 0.025-inch stainless steel archwire was inserted into the brackets and tied by elastomeric ligature. Debris level (via scanning electron microscopy), roughness, and frictional force were evaluated as-received and after 8 weeks of intraoral exposure. Mann-Whitney, Wilcoxon signed-rank, and Spearman correlation tests were used for statistical analysis at the .05 level of significance.Results:There were significant increases in the level of debris (P  =  .0004), roughness of orthodontic wires (P  =  .002), and friction (P  =  .0001) after intraoral exposure. Significant positive correlations (P < .05) were observed between these three variables.Conclusion:Stainless steel rectangular wires, when exposed to the intraoral environment for 8 weeks, showed a significant increase in the degree of debris and surface roughness, causing an increase in friction between the wire and bracket during the mechanics of sliding.     

Comparative short-term in vitro analysis of mutans streptococci adhesion on esthetic,nickel-titanium,and stainless-steel arch wires

Objective: To test the hypothesis that there are no differences in mutans streptococci (MS) adhesion between esthetic and metallic orthodontic arch wires based on their surface characteristics.Materials and Methods:Surface roughness (R_a) and apparent surface free energy (SFE) were measured for six wires—four esthetic, one nickel-titanium (NiTi), and one stainless-steel (SS)—using profilometry and dynamic contact angle analysis, respectively. The amount of MS (Streptococcus mutans and Streptococcus sobrinus) adhering to the wires was quantified using the colony-counting method. The surfaces, coating layers, and MS adhesion were also observed by scanning electron microscopy. Statistical significance was set at P < .05.Results:The R_a values of the esthetic wires were significantly different from one another depending on the coating method (P < .05). The NiTi wire showed the highest SFE, followed by the SS wire and then the four esthetic wires. The NiTi wires produced a significantly higher MS adhesion than did the SS wires (P < .05). The esthetic wires showed significantly lower MS adhesions than did the NiTi wire (P < .05). Pearson correlation analyses found moderate significant positive correlations between the SFE and the S mutans and S sobrinus adhesions (r  =  .636/.427, P < .001/P  =  .001, respectively).Conclusions:The hypothesis is rejected. This study indicates that some esthetic coatings on NiTi alloy might reduce MS adhesion in vitro in the short term.     

Effect of time and pH on physical-chemical properties of orthodontic brackets and wires

Objective:To test the hypothesis that treatment time, debris/biofilm, and oral pH have an influence on the physical-chemical properties of orthodontic brackets and arch wires.Materials and Methods:One hundred twenty metal brackets were evaluated. They were divided into four groups (n  =  30) according to treatment time: group C (control) and groups T12, T24, and T36 (brackets recovered after 12, 24, and 36 months of treatment, respectively). Rectangular stainless-steel arch wires that remained in the oral cavity for 12 to 24 months were also analyzed. Dimensional stability, surface morphology, composition of brackets, resistance to sliding of the bracket-wire set, surface roughness of wires, and oral pH were analyzed. One-way analysis of variance, followed by a Tukey multiple comparisons test, was used for statistical analysis (P < .05).Results:Carbon and oxygen were shown to be elements that increased expressively and in direct proportion to time, and there was a progressive increase in the coefficient of friction and roughness of wires as a function of time of clinical use after 36 months. Oral pH showed a significant difference between group T36 and its control (P  =  .014).Conclusions:The hypothesis was partially accepted: treatment time and biofilm and debris accumulation in bracket slots were shown to have more influence on the degradation process and frictional force of these devices than did oral pH.     

In vitro biocompatibility of nickel-titanium esthetic orthodontic archwires

Objective:To investigate the cytotoxicity of nickel-titanium (NiTi) esthetic orthodontic archwires with different surface coatings.Materials and Methods:Three fully coated, tooth-colored NiTi wires (BioCosmetic, Titanol Cosmetic, EverWhite), two ion-implanted wires (TMA Purple, Sentalloy High Aesthetic), five uncoated NiTi wires (BioStarter, BioTorque, Titanol Superelastic, Memory Wire Superelastic, and Sentalloy), one β-titanium wire (TMA), and one stainless steel wire (Stainless Steel) were considered for this study. The wire samples were placed at 37°C in airtight test tubes containing Dulbecco’s Modified Eagle’s Medium (0.1 mg/mL) for 1, 7, 14, and 30 days. The cell viability of human gingival fibroblasts (HGFs) cultured with this medium was assessed by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. Data were analyzed by a two-way analysis of variance (α  =  .05).Results:The highest cytotoxic effect was reached on day 30 for all samples. The archwires exhibited a cytotoxicity on HGFs ranging from “none” to “slight,” with the exception of the BioTorque, which resulted in moderate cytotoxicity on day 30. Significant differences were found between esthetic archwires and their uncoated pairs only for BioCosmetic (P  =  .001) and EverWhite (P < .001).Conclusions:Under the experimental conditions, all of the NiTi esthetic archwires resulted in slight cytotoxicity, as did the respective uncoated wires. For this reason their clinical use may be considered to have similar risks to the uncoated archwires.     

Streptococcus mutans adhesion on nickel titanium (NiTi) and copper-NiTi archwires: A comparative prospective clinical study

Objectives:To compare the adhesion of Streptococcus mutans to nickel titanium (NiTi) and copper-NiTi (Cu-NiTi) archwires and to correlate the adhesion to surface characteristics (surface free energy and surface roughness) of these wires.Materials and Methods:A total of 16 patients undergoing orthodontic treatment with preadjusted edgewise appliances were included in the study. 0.016” and 0.016” × 0.022” NiTi and Cu-NiTi archwires in as-received condition and after 4 weeks of intraoral use were studied for S mutans adhesion using real-time polymerase chain reaction. Surface roughness and surface free energy were studied by three-dimensional surface profilometry and dynamic contact angle analysis, respectively.Results:S mutans adhesion was more in Cu-NiTi archwires. These wires exhibited rougher surface and higher surface free energy when compared to NiTi archwires.Conclusions:S mutans adhesion, surface roughness, and surface free energy were greater in Cu-NiTi than NiTi archwires. Surface roughness and surface free energy increased after 4 weeks of intraoral exposure for all of the archwires studied. A predominantly negative correlation was seen between the cycle threshold value of adherent bacteria and surface characteristics.     

In vitro and in vivo mechanical stability of orthodontic mini-implants: Effect of sandblasted,large-grit,and anodic-oxidation vs sandblasted,large-grit,and acid-etching

Objective:To compare in vivo and in vitro mechanical stability of orthodontic mini-implants (OMIs) treated with a sandblasted, large-grit, and anodic-oxidation (SLAO) method vs those treated with a sandblasted, large-grit, and acid-etching (SLA) method.Materials and Methods:Fifty-four titanium OMIs (cylindrical shape, drill-free type; diameter  =  1.45 mm, length  =  8 mm, Biomaterials Korea Inc, Seoul, Korea) were allocated into control, SLA, and SLAO groups (N  =  12 for in vivo and N  =  6 for in vitro studies per group). In vitro study was carried out on a polyurethane foam bone block (Sawbones, Pacific Research Laboratories Inc, Vashon, Wash). In vivo study was performed in the tibias of Beagles (6 males, age  =  1 year, weight  =  10 to 13 kg; OMIs were removed at 8 weeks after installation). For insertion and removal of OMIs, the speed and maximum torque of the surgical engine were set to 30 rpm and 40 Ncm, respectively. Maximum torque (MT), total energy (TE), and near peak energy (NPE) during the insertion and removal procedures were statistically analyzed.Results:In the in vitro study, although the control group had a higher insertion MT value than the SLA and SLAO groups (P < .01), no differences in insertion TE and NPE or in any of the removal variables were noted among the three groups. In the in vivo study, the control group exhibited higher values for all insertion variables compared with the SLA and SLAO groups (MT, P < .001; TE, P < .01; NPE, P < .001). Although no difference in removal TE and removal NPE was noted among the three groups, the SLAO group presented with a higher removal MT than the SLA and control groups (P < .001).Conclusions:SLAO treatment may be an effective tool in reducing insertion damage to surrounding tissue and improving the mechanical stability of OMIs.     

Analysis of the effect of CPP-ACP tooth mousse on enamel remineralization by circularly polarized images

Objective:To evaluate the effect of casein phosphopeptide–amorphous calcium phosphate tooth mousse on the remineralization of bovine incisor by circularly polarized images.Methods:Eighty bovine incisors, each with a 4 × 4 mm artificially demineralized area, were used. The samples were divided into four groups: Group A, casein phosphopeptide–amorphous calcium phosphate tooth mousse; Group B, fluoride toothpaste; Group C, casein phosphopeptide–amorphous calcium phosphate tooth mousse and fluoride toothpaste; and Group D, no treatment. Circularly polarized images were taken after the specimens were treated for 3, 6, 9, or 12 weeks, and the size of the demineralized area and the mean grey level were measured. Data analysis was done using repeated measures variance analysis. Pearson correlation coefficients were computed to evaluate the correlation between the size of the demineralized area and the mean grey level.Results:In all four groups, the size of the demineralized area and the mean grey level declined with time. The size of the demineralized area of Group C was significantly smaller than that of Group A at the end of the third and sixth weeks (P  =  .039, P  =  .000, respectively), and the mean grey level of Group C was lower than that of Group A at the end of the 6th and 12th weeks (P  =  .037, P  =  .004, respectively). At the end of the 6th, 9th, and 12th weeks, the size of the demineralized area of Group C was smaller (P  =  .000, P  =  .005, P  =  .005, respectively) and the mean grey level was lower (P  =  .000) than those of Group B. No statistically significant correlations were detected between the size of the demineralized area and the mean grey level.Conclusion:Casein phosphopeptide–amorphous calcium phosphate tooth mousse can reduce the size and mean grey level of demineralized areas and promote the remineralization of bovine enamel. Combined application with fluoride toothpaste strengthens the effect.     

Effects of intraoral aging on surface properties of coated nickel-titanium archwires

Objective:To evaluate the effects of intraoral aging on surface properties of esthetic and conventional nickel-titanium (NiTi) archwires.Materials and Methods:Five NiTi wires were considered for this study (Sentalloy, Sentalloy High Aesthetic, Superelastic Titanium Memory Wire, Esthetic Superelastic Titanium Memory Wire, and EverWhite). For each type of wire, four samples were analyzed as received and after 1 month of clinical use by an atomic force microscope (AFM) and a scanning electronic microscope (SEM). To evaluate sliding resistance, two stainless steel plates with three metallic or three monocrystalline brackets, bonded in passive configuration, were manufactured; four as-received and retrieved samples for every wire were pulled five times at 5 mm/min for 1 minute by means of an Instron 5566, recording the greatest friction value (N). Data were analyzed by one-way analysis of variance and by Student''s t-test.Results:After clinical use, surface roughness increased considerably. The SEM images showed homogeneity for the as-received control wires; however, after clinical use esthetic wires exhibited a heterogeneous surface with craters and bumps. The lowest levels of friction were observed with the as-received Superelastic Titanium Memory Wire on metallic brackets. When tested on ceramic brackets, all the wires exhibited an increase in friction (t-test; P < .05). Furthermore, all the wires, except Sentalloy, showed a statistically significant increase in friction between the as-received and retrieved groups (t-test; P < .05).Conclusion:Clinical use of the orthodontic wires increases their surface roughness and the level of friction.     

Effect of adhesion boosters on indirect bracket bonding

Objective:To determine the influence of two adhesion boosters on shear bond strength and on the bond failure location of indirectly bonded brackets.Materials and Methods:Sixty bovine incisors were randomly divided into three groups (n  =  20), and their buccal faces were etched using 37% phosphoric acid. In group 1 (control), brackets were indirectly bonded using only Sondhi adhesive. In groups 2 and 3, the adhesion boosters Enhance Adhesion Booster and Assure Universal Bonding Resin, respectively, were applied before bonding with Sondhi. Maximum bond strength was measured with a universal testing machine, and the location of bond failure was evaluated using the Adhesive Remnant Index (ARI). One-way analysis of variance followed by the Tukey test (P < .05) was used to compare the shear bond strength among groups, and the differences in ARI scores were evaluated using the Kruskal-Wallis test (P < .05). The Pearson correlation coefficient was calculated to determine whether there was any correlation between bond strength and ARI scores.Results:The mean shear bond strength in group 3 was significantly higher (P < .01) than in the other groups. Evaluation of the locations of bond failure revealed differences (P < .05) among the three groups. There was a moderate correlation between bond strength and ARI scores within group 3 (r  =  0.5860, P < .01).Conclusion:In vitro shear bond strength was acceptable in all groups. The use of the Assure adhesion booster significantly increased both the shear bond strength of indirectly bonded brackets and the amount of adhesive that remained on the enamel after bracket debonding.     

In vitro Streptococcus mutans adhesion and biofilm formation on different esthetic orthodontic archwires

ObjectivesTo evaluate the ability of different esthetic archwires to retain oral biofilms in vitro.Materials and MethodsSeven different brands of coated orthodontic archwires were tested: two epoxy coated, two polytetrafluoroethylene coated, two rhodium coated, and one silver plus polymer coated. Conventional uncoated metallic archwires were used as controls. Streptococus mutans adherence to archwires was quantified by colony count following 24 hours of biolfilm growth, and total wire-associated biofilm was measured using a crystal violet staining assay. For both tests, two conditions were used: 0% sucrose and 3% sucrose. For statistical analysis, P < .05 was considered as statistically significant.ResultsFor S. mutans colony forming units per biofilm, there were no statistically significant differences among the various archwires (P = .795 for 0% sucrose; P = .905 for 3% sucrose). Regarding total biofilm formed on archwires in the 3% sucrose condition, there were statistically significant differences in crystal violet staining only for the comparison between Niti Micro Dental White and Copper Ni-Ti wires (P < .05).ConclusionsThe clinical use of esthetic-coated orthodontic wires may be considered to have similar risks as uncoated archwires for biofilm retention.     

Analysis of smile esthetics in American Board of Orthodontic patients

Objective:To investigate the common denominators of an esthetically pleasing smile in patients who were considered to be successfully treated upon the submission to American Board Orthodontics (ABO) clinical examination.Material and Methods:A total of 462 patients were examined. Ninety subjects that fulfilled the inclusion criteria were included. Standardized digital smile photographs of the subjects were rated by 30 panel members, including orthodontists, general dentists, and parents of orthodontic patients, using a numeric version of the visual analog scale. Three groups were formed using the mean esthetic score ± standard deviation range: unattractive (n  =  21), average (n  =  47), and attractive (n  =  22) smiles. Eleven smile characteristics were digitally measured on the photographs and compared between the groups using one-way analysis of variance and χ² tests. Additionally, regression analyses were used to investigate the association of the smile characteristics with the esthetic score.Results:A significant difference was found between the three groups for the comparison of smile arc relationship (P < .001). When all the variables used in this study were entered in the regression analysis, a positive association was found (r  =  0.658; r²  =  0.434; P < .001). Additionally, two models were defined using stepwise regression. The first model included the smile arc (r  =  0.478; r²  =  0.228; P < .001), and the second model had both the smile arc and right gingival display/visible dentition display ratio (r  =  0.567; r²  =  0.321; P < .001).Conclusions:A harmonious smile arc relationship and less gingival display during a smile are significantly associated with smile attractiveness in patients considered successfully treated according to ABO standards.     

Condylar displacement between centric relation and maximum intercuspation in symptomatic and asymptomatic individuals

Objective:To measure condylar displacement between centric relation (CR) and maximum intercuspation (MIC) in symptomatic and asymptomatic subjects.Materials and Methods:The sample comprised 70 non-deprogrammed individuals, divided equally into two groups, one symptomatic and the other asymptomatic, grouped according to the research diagnostic criteria for temporomandibular disorders (RDC/TMD). Condylar displacement was measured in three dimensions with the condylar position indicator (CPI) device. Dahlberg''s index, intraclass correlation coefficient, repeated measures analysis of variance, analysis of variance, and generalized estimating equations were used for statistical analysis.Results:A greater magnitude of difference was observed on the vertical plane on the left side in both symptomatic and asymptomatic individuals (P  =  .033). The symptomatic group presented higher measurements on the transverse plane (P  =  .015). The percentage of displacement in the mesial direction was significantly higher in the asymptomatic group than in the symptomatic one (P  =  .049). Both groups presented a significantly higher percentage of mesial direction on the right side than on the left (P  =  .036). The presence of bilateral condylar displacement (left and right sides) in an inferior and distal direction was significantly greater in symptomatic individuals (P  =  .012). However, no statistical difference was noted between genders.Conclusion:Statistically significant differences between CR and MIC were quantifiable at the condylar level in asymptomatic and symptomatic individuals.     

Physical Properties of Conventional and Super Slick Elastomeric Ligatures after Intraoral Use

Objective:To investigate the change in the physical properties of conventional and Super Slick elastomeric ligatures after they have been in the mouth.Materials and Methods:Nine healthy volunteers took part. One orthodontic bracket was bonded to a premolar tooth in each of the four quadrants of the mouth. Two conventional and two Super Slick elastomeric ligatures were placed at random locations on either side of the mouth. The ligatures were collected after various time intervals and tested using an Instron Universal testing machine. The two outcome measures were failure load and the static frictional resistance.Results:The failure load for conventional ligatures was reduced to 67% of the original value after 6 weeks in situ. Super Slick elastomeric ligatures showed a comparable reduction after 6 weeks in situ (63% of original value). There were no statistical differences in the static friction between conventional and Super Slick elastomerics that had been in situ for either 24 hours (P  =  .686) or 6 weeks (P  =  .416). There was a good correlation between failure load and static friction (r  =  .49).Conclusions:There were statistically significant differences in the failure loads of elastomerics that had not be placed in the mouth and those that had been in the mouth for 6 weeks. There were no differences in the static frictional forces produced by conventional and Super Slick ligatures either before or after they had been placed in the mouth. There appears to be a direct proportional relationship between failure load and static friction of elastomeric ligatures.     

Skeletal and Soft Tissue Point A and B Changes Following Orthodontic Treatment of Nepalese Class I Bimaxillary Protrusive Patients

Objectives:To test the hypothesis that there is no correlation in the interrelationships of skeletal and soft tissue points A and B with anterior teeth retraction.Materials and Methods:Thirty adult Class I bimaxillary protrusion patients treated with preadjusted appliances after first premolar extraction were included. Pretreatment and posttreatment variables were compared using paired t-test, and the relationship of soft and hard tissue variables was studied using Pearson correlation coefficient and linear regression equation.Results:Mean point A and soft tissue point A (sA) were retracted 2.7 mm (P < .001) and 1.7 mm (P < .001), and mean point B and soft tissue point B (sB) were retracted 2.1 mm (P < .001) and 1.2 mm (P < .001), respectively. Mean ratio of retraction of point A with sA and point B with sB was 1.5∶1 and 1.7∶1, respectively. A significant degree of correlation existed between retraction of point A and soft tissue point A (r  =  0.648, P < .01) and point B and soft tissue point B (r  =  0.806, P < .01). Linear regression analysis used to predict the changes in sA and sB showed significant relationship between point A and sA (r  =  0.543, F  =  11.7, R²  =  0.29, P < .001) and point B and sB (r  =  0.825, F  =  59.7, R²  =  0.68, P < .001). Decreases in hard and soft tissue convexity were due to the retraction of the skeletal and soft tissue points A and B in addition to the lips retraction.Conclusions:The hypothesis is rejected. Retraction of skeletal point A and B lead to retraction of sA and sB under controlled root positions. Nearly proportionate changes existed in the skeletal points and overlying corresponding soft tissue points.     

Velopharyngeal changes after maxillary distraction in cleft patients using a rigid external distraction device: A retrospective study

Objective:To evaluate early and late velopharyngeal changes in cleft lip and palate (CLP) patients after use of the Rigid External Distractor (RED) device and to correlate these changes to the amount of maxillary advancement.Materials and Methods:Thirty Class III CLP patients were included in the study. Maxillary advancement was performed using the RED device in combination with titanium miniplates and screws for anchorage. Lateral cephalograms, nasometer, and nasopharyngoscope records were taken before distraction, immediately after distraction, and 1 year after distraction. A paired t-test was used to detect differences at P < .05.Results:SNA angle and A point and ANS to Y axis were significantly increased after maxillary distraction (P  =  .0001). Statistically significant increases in nasopharyngeal and oropharyngeal depths, velar angle, and need ratio were also found (P  =  .0001). Nasalance scores showed a significant increase (P  =  .008 for nasal text and .044 for oral text). A significant positive correlation was observed between the amount of maxillary advancement and the increase in nasopharyngeal depth and hypernasality (P  =  .012 and .026, respectively).Conclusions:Nasopharyngeal function was deteriorated after maxillary advancement in CLP patients. There was a significant positive correlation between the amount of maxillary advancement and the increase in nasopharyngeal depth and hypernasality.     

Three-dimensional upper-airway assessment in patients with bronchial asthma

Objective:To assess the upper airway (UAW) total volume (TV), the nasopharyngeal narrowest area (NNA), and the oropharyngeal narrowest area (ONA) in patients with bronchial asthma.Materials and Methods:The sample consisted of 52 patients divided into two groups: the control group (n  =  26; mean age  =  14.85 years), which consisted of patients not suffering from bronchial asthma; and the asthmatic group (n  =  26; mean age  =  16.65 years), which consisted of patients with bronchial asthma. To assess UAW-related variables (TV, NNA, and ONA), cone-beam computed tomography scans of the patients were evaluated by means of the Dolphin Imaging software 11.5. All measurements were repeated after 30 days, and the results were submitted to reliability tests by means of the intraclass correlation coefficient and the Bland-Altman agreement test. The values obtained for TV, NNA, and ONA for each group were compared by using Student''s t-test for independent samples (5% level of significance).Results:The results showed that the groups were matched concerning gender, cephalometric characteristics, and type of malocclusion. The asthmatic group had significantly lower TV (P  =  .01) and ONA (P  =  .007) than the control group. However, no significant difference was observed for NNA between the groups (P  =  .54).Conclusions:Bronchial asthma may be a determining factor for the reduction of UAW dimensions, as patients with asthma showed significant reductions in TV and ONA dimensions.     

Effects of self-ligating and conventional brackets on halitosis and periodontal conditions

Objective:To evaluate the effects of fixed orthodontic treatment with steel-ligated conventional brackets and self-ligating brackets on halitosis and periodontal health.Materials and Methods:Sixty patients, at the permanent dentition stage aged 12 to 18 years, who had Angle Class I malocclusion with mild-to-moderate crowding were randomly selected. Inclusion criteria were nonsmokers, without systematic disease, and no use of antibiotics and oral mouth rinses during the 2-month period before the study. The patients were subdivided into three groups randomly: the group treated with conventional brackets (group 1, n  =  20) ligated with steel ligature wires, the group treated with self-ligating brackets (group 2, n  =  20), and the control group (group 3, n  =  20). The periodontal records were obtained 1 week before bonding (T1), immediately before bonding (T2), 1 week after bonding (T3), 4 weeks after bonding (T4), and 8 weeks after bonding (T5). Measurements of the control group were repeated within the same periods. The volatile sulfur components determining halitosis were measured with the Halimeter at T2, T3, T4, and T5. A two-way repeated measures of analysis of variance (ANOVA) was used to compare the groups statistically.Results:No statistically significant group × time interactions were found for plaque index, gingival index, pocket depth, bleeding on probing, and halitosis, which means three independent groups change like each other by time. The risk of tongue coating index (TCI) being 2 was 10.2 times higher at T1 than at T5 (P < .001). Therefore, the probability of higher TCI was decreased by time in all groups.Conclusions:The self-ligating brackets do not have an advantage over conventional brackets with respect to periodontal status and halitosis.     

Dentoskeletal changes following mini-implant molar intrusion in anterior open bite patients

Objective:To evaluate skeletal and dental changes after intrusion of the maxillary molars in subjects with anterior open bite.Materials and Methods:This retrospective cephalometric study evaluated skeletal and dental changes resulting from the use of maxillary orthodontic mini-implants in 31 consecutively treated patients. Radiographs were taken at the start and end of maxillary molar intrusion to evaluate the associated changes. Statistical analysis was performed using a one-sample t-test.Results:The mean treatment observation time was 1.31 years (SD  =  2.03). The maxillary first molars (P  =  0.0026) and second molars (P  =  0.039) were intruded. However, the mandibular first molars (P  =  0.0004) and second molars (P  =  0.003) erupted in adolescent patients. Both the maxillary and mandibular first molars inclined distally (P  =  0.025 and P  =  0.044, respectively). The mandibular plane angle decreased (P  =  0.036), lower facial height decreased (P  =  0.002), and the occlusal plane angle increased (P  =  0.009). The overbite increased (P < .0001). The ANB angle decreased (P < .0001). Mandibular dental and skeletal changes were more apparent in adolescents, while adults tended toward maxillary changes.Conclusions:Vertical traction from orthodontic mini-implants reduces the maxillary posterior dentoalveolar height, thereby assisting orthodontic closure of anterior open bite. However, simultaneous eruption or extrusion of the mandibular molars should be controlled. Adolescent patients tend to demonstrate more favorable effects of mandibular autorotation than do adults.     

Another way of looking at treatment stability

Objective:To determine the contribution of normal physiological changes to the overall manifestation of a relapse after orthodontic treatment. We analyzed long-term changes in the dentition of patients with Class I malocclusions after orthodontic treatment compared with a representative group with untreated Class I malocclusions.Materials and Methods:Study participants (n  =  66; mean age, 12 years at treatment initiation) were treated for Class I malocclusions. Dental changes were evaluated at 2, 5, 10, and 15 years after treatment. Control participants (n  =  79) had untreated Class I malocclusions (n  =  53 evaluated at ages 12 and 22 years; n  =  26 evaluated at ages 19 and 39 years). Dental changes were evaluated with the Peer Assessment Rating (PAR) index.Results:In untreated and treated groups, PAR scores increased over time with gender-specific changes. In the untreated groups, the PAR score significantly increased in male participants between the ages of 12 and 22 years (P  =  .04) and in female participants between the ages of 19 and 39 years (P  =  .001). In the treated group, early posttreatment changes were primarily related to the initial treatment response. Later changes in the PAR score could be attributed to physiological changes, with the same gender-specific changes as those observed in the untreated group.Conclusions:The pattern of physiological changes in dentition for participants between the ages of 12 and 39 was different between sexes. Females showed more relapse than males between 10 and 15 years posttreatment. This distinction should be considered when evaluating long-term orthodontic treatment responses.