Proton‐Conducting Properties of Acid‐Doped Poly(glycidyl methacrylate)‐1,2,4‐Triazole Systems

1,2,4‐triazole‐functional PGMA polymers have been synthesized and their anhydrous proton‐conducting properties were investigated after doping with phosphoric acid and triflic acid. PGMA was prepared by solution polymerization and then modified with 1H‐1,2,4‐triazole (Tri) and 3‐amino‐1,2,4‐triazole (ATri). FT‐IR, ¹³C NMR and elemental analysis verify the high immobilization of the triazoles in the polymer chain. Phosphoric‐acid‐doped polymers showed lower T_g and higher proton conductivities. PGMA‐Tri 4 H₃PO₄ showed a maximum water‐free proton conductivity of approximately 10^?2 S · cm^?1 while that of PGMA‐ATri 2 H₃PO₄ was 10^?3 S · cm^?1. The structure and dynamics of the polymers were explored by ¹H MAS and ¹³C CP‐MAS solid‐state NMR.

     

Poly(carbazole)‐Based Copolymers Containing Deep‐Blue Chromophore for Polymer Light‐Emitting Diode Applications

A new series of two poly(carbazole)‐based copolymers (poly(9‐hexyl‐carbazole‐co‐9‐(6‐(3‐(4‐phenylquinolin‐2‐yl)carbazol‐9‐yl)hexyl)carbazole) (PCVz) and poly(9,9‐dioctylfluorene‐co‐9‐(6‐(3‐(4‐phenylquinolin‐2‐yl)carbazol‐9‐yl)hexyl)carbazole) (PFCVz)) containing carbazoylphenylquinoline pendant groups were synthesized via the Suzuki coupling reaction for polymer light‐emitting diode applications. The electro‐optical properties of ITO/PEDOT/Polymer/PBD/LiF/Al devices based on these copolymers were investigated using UV‐visible, photoluminescence, and electroluminescence spectroscopy. The turn‐on voltages of the copolymer devices were found to be 6.0–8.0 V. The maximum brightness and luminescence efficiency of the copolymers device were found to be 230 cd · m^?2 and 0.28 cd · A^?1 at 11 V, respectively.

     

Crystallization and Ring‐Banded Spherulite Morphology of Poly(ethylene oxide)‐block‐Poly(ε‐caprolactone) Diblock Copolymer

Summary: The crystallization behavior of crystalline‐crystalline diblock copolymer containing poly(ethylene oxide) (PEO) and poly(ε‐caprolactone) (PCL), in which the weight fraction of PCL is 0.815, has been studied via differential scanning calorimeter (DSC), wide‐angle X‐ray diffraction (WAXD), and polarized optical microscopy (POM). DSC and WAXD indicated that both PEO and PCL blocks crystallize in the block copolymer. POM revealed a ring‐banded spherulite morphology for the PEO‐b‐PCL diblock copolymer.

DSC heating curve for the PEO‐b‐PCL block copolymer.     

Polyrotaxanes of Pyrene–Triazole Conjugated Azomethine and α‐Cyclodextrin with High Fluorescence Properties

The paper reports on the preparation of a new 2‐rotaxane monomer through an acid coupling reaction between 1‐pyrenecarboxaldehyde and α‐CD/3,5‐diamino‐1,2,4‐triazole inclusion complex. Pyrenyl groups are large enough to provide a blocking effect toward cyclodextrin de‐threading. The oxidative C? C coupling of 2‐rotaxane in the presence of RuCl₃ catalyst afforded conjugated azomethine polyrotaxanes. The expected modifications of the solubility, morphology, film forming ability for rotaxane polymer were proved. As shown by fluorescence and UV‐vis spectroscopy, a material with optical properties appropriate for use in photonics was obtained.

     

Amphiphilic Block Copolymers Containing Regioregular Poly(3‐hexylthiophene) and Poly(2‐ethyl‐2‐oxazoline)

Poly(3‐hexylthiophene)‐block‐poly(2‐ethyl‐2‐oxazoline) amphiphilic rod–coil diblock copolymers have been synthesized by a combination of Grignard metathesis (GRIM) and ring‐opening cationic polymerization. Diblock copolymers containing 5, 15, and 30 mol‐% poly(2‐ethyl‐2‐oxazoline) have been synthesized and characterized. The synthesized rod–coil block copolymers display nanofibrillar morphology where the density of the nanofibrills is dependent on the concentration of the poly(2‐ethyl‐2‐oxazoline) coil segment. The conductivity of the diblock copolymers was lowered from 200 to 35 S · cm^?1 with an increase in the content of the insulating poly(2‐ethyl‐2‐oxazoline) block. By contrast, the field‐effect mobility decreased by 2–3 orders of magnitude upon the incorporation of the poly(2‐ethyl‐2‐oxazoline) insulating segment.

     

Studies on the Synthesis and Conductivity of a Novel Reactive Ladder‐Like Poly(β‐cyanoethylsilsesquioxane) and Poly[(β‐cyanoethylsilsesquioxane)‐co‐(β‐methylsilsesquioxane)]

Two novel reactive poly(β‐cyanoethylsilsesquioxane) ( CN‐T ) and poly[(β‐cyanoethylsilsesquioxane)‐co‐(β‐methylsilsesquioxane)] ( CN‐Me‐T ) have been synthesized successfully for the first time via stepwise coupling polymerization (SCP). A variety of characterization methods including FTIR, ¹H NMR, ²⁹Si NMR, X‐ray diffraction (XRD), differential scanning calorimetry (DSC) and vapor pressure osmometry (VPO) were combined to demonstrate that the structures of the title polymers possess ordered ladder‐like structures. As expected, the ionic conductivity of these polymers mixed homogeneously with lithium perchlorate reached 10^?6 S · cm^?1 at room temperature and obviously increased with the raise of temperature.

     

Macrocyclic and Acyclic Bis(2,5‐diphenyl‐1,3,4‐oxadiazole)s with Electron‐Transporting and Hole‐Blocking Ability in Organic Electroluminescent Devices

Summary: Two types of bis(2,5‐diphenyl‐1,3,4‐oxadiazole)s, macrocyclic and acyclic, were prepared and evaluated as electron‐transporting and hole‐blocking materials in phosphorescent EL devices. Maximum efficiencies of η_ext = 10.4% at J = 0.11 mA · cm⁻² for the macrocycle and η_ext = 14.1% at J = 3.01 mA · cm⁻² for the acycle were observed. X‐ray crystallographic analysis and DSC measurements revealed a strong intermolecular interaction between the macrocycles and weaker intermolecular interactions between the acycles. The EL characteristics depend on the intermolecular interactions.

The two types of bis(2,5‐diphenyl‐1,3,4‐oxadiazole)s used in the study.     

Active Poly(4‐chloromethyl styrene)‐Functionalized Multiwalled Carbon Nanotubes

Concentrated nitric acid‐treated multiwalled carbon nanotubes (MWCNTs) are functionalized with active poly(4‐chloromethyl styrene) (PCMS) through the esterification reaction of the carboxyl groups of the former and the p‐benzyl chloride groups of the latter in the presence of a phase‐transfer catalyst. Characterization using Raman spectroscopy, Fourier transform infrared spectroscopy, and hydrogen nuclear magnetic resonance spectroscopy demonstrates that the active PCMS chains are chemically tethered onto the side walls (or surfaces) of the MWCNTs. The core‐shell nanostructure of active PCMS‐modified MWCNTs (MWCNT‐PCMS) can be observed by high resolution transmission electron microscopy, and the amount of PCMS present is 31.3 wt% by thermogravimetric analysis. Solubility testing shows that MWCNT‐PCMS dissolves well in tetrahydrofuran, chloroform, toluene, and N,N‐dimethylformamide, and the maximum nanotube concentration in toluene is 413 mg L^?1.

     

Characterization of Water‐Dispersible n‐Type Poly(benzimidazobenzophenanthroline) Derivatives

Novel water dispersible poly(benzimidazobenzophenanthroline) polymers functionalized with poly(ethylene oxide) (BBL:PEO) have been investigated by cyclic voltammetry, in situ UV‐vis spectroscopy and atomic force microscopy. The cyclic voltammograms recorded during n‐doping indicate that the drop coated BBL:PEO films retain their properties despite functionalization. A small influence of the PEO side chains on redox properties of the investigated polymers was found, diminishing however after annealing. During spectroscopic experiments structural changes connected with polymer charging were observed (in accordance with a two electron transfer process). The functionalization of BBL with PEO side chains provided an easy processing method to obtain smooth and reproducible polymer films.

     

Aromatic Polyethers with a 4‐Chloro‐3‐trifluoromethylphenyl Group

Summary: A novel bisphenol, (4‐chloro‐3‐trifluoromethyl)phenylhydroquinone (3FC‐PH), was synthesized via a three‐step synthetic procedure. Four aromatic polyethers based on 3FC‐PH were prepared via a nucleophilic aromatic substitution polycondensation. These polymers had a high thermal stability, and the temperatures at a 5% weight loss were above 516 °C in air. The solubility of the polyethers was improved by the introduction of bulky pendant groups. The average refractive indices of the polymer films at 1 320 nm were in the range 1.5381–1.6145. The dielectric constants of the polyether films estimated from the refractive indices were 2.69–2.98. Highly fluorinated 3FC‐PAE exhibited lower light absorption in the near‐IR region.

Part of the ¹H NMR spectra of 3FC‐PAE.     

Tunable Microcellular Morphologies from Poly(ferrocenylsilane) Ceramic Precursors Foamed in Supercritical CO2

Summary: Poly(ferrocenylmethylphenylsilane) (PFMPS) and poly[ferrocenylmethyl(phenylacetylido)silane] (PFMPAS) homopolymers are organometallic polymers that can serve as precursors to magnetically‐active ceramics. In this work, PFMPS and PFMPAS films ranging in thickness from 30 to 220 μm have been exposed to scCO₂ over a broad range of saturation pressures, temperatures and times to produce surface‐constrained microcellular polymeric foams. Electron microscopy identifies viable foaming windows and reveals that foams with submicron cell sizes can be generated by judicious selection of exposure conditions. Cell shape anisotropy can likewise be varied from being nearly spherical to vertically elongated. Curvature in the films and non‐negligible surface roughness create paths that facilitate CO₂ diffusion, resulting in the formation of “V‐directional” cells oriented at approximately 30° to the film surface. The development of bimodal cell size distributions is attributed to temperature variation during depressurization and/or stepwise homogeneous and heterogeneous nucleation. These results are prerequisite for the production of magnetically‐active porous ceramics from pyrolyzed PFS foams.

SEM image of a PFMPS foam generated in scCO₂ illustrating considerable cell anisotropy: the cells are tilted with respect to the film surface.     

Multifunctional Porous Poly(vinylidene fluoride)‐graft‐Poly(butyl methacrylate) with Good Li+ Ion Conductivity

PnBMA is grafted on PVDF using ATRP in NMP solution at 90 °C and characterized by means of 1D and 2D NMR. ¹⁹F NMR spectra clearly reveal that the attack occurs on the head‐head >CF₂ groups. Cast PB films show a honeycomb‐patterned porous microstructure, and the “breath‐figure” model is used to explain pore formation. FT‐IR spectra suggest a supramolecular interaction between >C?O groups of PnBMA and >CF₂ groups of PVDF. Storage modulus, loss modulus and stress at break decrease with graft conversion, but the strain at break increases significantly. The toughness of the copolymers also increases dramatically (882%). The porous materials can be applied as solid‐state electrolytes (Li⁺‐doped) with good ionic conductivity (10^?5 S · cm^?1).

     

Click‐Chemistry: An Alternative Way to Functionalize Poly(2‐methyl‐2‐oxazoline)

CROP has been used to synthesize well‐defined POXZ with a monofunctional (iodomethane) or a bifunctional (1,3‐diiodopropane) initiator. POXZ has been functionalized with an azido group at one (α‐azido‐POXZ, = 3.58 × 10³ g · mol^?1) or both ends (α,ω‐azido‐POXZ, = 6.21 × 10³ g · mol^?1) of the macromolecular chain. The Huisgen 1,3‐dipolar cycloaddition has been investigated between azido‐POXZ and a terminal alkyne on a small or larger molecule (PEG). In each case, the click reaction has been successful and quantitative. In this way, different telechelic polymers (polymers bearing different functions such as acrylate, epoxide, or carboxylic acid) and block copolymers of POXZ and PEG have been prepared. The polymers have been characterized by means of FTIR, ¹H NMR, and SEC.

     

Poly(N‐hexyl‐cyclopenta[c]pyrrole) – A Novel 1,3,4‐Alkyl‐substituted Polypyrrole Soluble in Organic Solvents and Redox Conducting

Summary: N‐Hexyl‐cyclopenta[c]pyrrole was synthesized and electrochemically and chemically polymerized to a novel 1,3,4‐alkyl‐substituted polypyrrole. The polymer was characterized in solution and as thin solid film by cyclic voltammetry, UV‐vis, FTIR and NMR spectroscopy, MALDI mass spectroscopy, GPC analysis, electrochemical quartz crystal microbalance, ESR spectroscopy and in situ conductivity. The polymer, with a defect‐free structure and an average degree of polymerization of 13 (electrochemically prepared) and 24 (chemically prepared), is soluble (>1%) in acetone, acetonitrile and chlorinated solvents. Its in situ conductivity as a function of potential and doping charge has the typical features of redox conductivity with a maximum value of ca 1 × 10^?3 S · cm^?1.

Structure of poly(N‐hexyl‐cyclopenta[c]pyrrole).     

Transesterification of Poly(4,4′‐isopropylidene‐2,2′‐dimethyldiphenylene terephthalate) and Poly(ethylene adipate) Blend in Solution

Summary: Transesterification of poly(4,4′‐isopropylidene‐2,2′‐dimethyldiphenylene terephthalate) and poly(ethylene adipate) (PEA) has been carried out in concentrated o‐dichlorobenzene solution at 210 °C with Bu₂SnO as a catalyst. According to GPC data, during transesterification the reaction product acquires Flory MWD and only a slight degradation of chains proceeds in the system: on average each chain having undergone about one scission in 100 min. Chain structure of the reaction products was studied using ¹H NMR spectroscopy. The kinetic and statistical analysis of the process was performed using following assumptions: transesterification proceeds in a homogeneous medium as a reversible second‐order reaction between diads, and the product chain structure obeys the first‐order Markov statistics. Calculated dependences of the parameters characterizing an evolution of the chain structure during the reaction fit experimental data fairly well. In 100 min the reacting system reaches a state close to the equilibrium. The difference between distributions of diads of residues and units is considered.

Change of the terephthalate‐centered r‐triads content with time.     

Synthesis of New Hydrogels by Copolymerization of Poly(2‐methyl‐2‐oxazoline) Bis(macromonomers) and N‐Vinylpyrrolidone

New non‐ionic hydrogels were synthesized by radical homopolymerization of vinyl end‐functionalized poly(2‐methyl‐2‐oxazoline) bis(macromonomers), or by radical copolymerization of these bis(macromonomers) with N‐vinyl‐2‐pyrrolidone (NVP). The poly(2‐methyl‐2‐oxazoline) bis(macromonomers) were synthesized through “living” cationic ring‐opening polymerization of 2‐methyl‐2‐oxazoline (MeOXA), using, simultaneously, the known “initiating” and “end‐capping” method for synthesis of macromonomers. Chloromethyl styrene was used as initiator and N‐(4‐vinylbenzyl)‐piperazine was used as the terminating agent. Well defined poly(2‐methyl‐2‐oxazoline) bis(macromonomers) were obtained with P_n = 4, 11, and 17. The hydrogel structures were characterized by high‐resolution magic angle spinning NMR technique and their solvent absorption capacity was tested by swelling experiments in different solvents. The bis(macromonomers) were characterized by NMR spectroscopy and gel permeation chromatography.

Schematic of polymerization     

Synthesis and Characterization of Amphiphilic Poly(ethylene oxide)‐block‐poly(hexyl methacrylate) Copolymers

We describe the preparation of amphiphilic diblock copolymers made of poly(ethylene oxide) (PEO) and poly(hexyl methacrylate) (PHMA) synthesized by anionic polymerization of ethylene oxide and subsequent atom transfer radical polymerization (ATRP) of hexyl methacrylate (HMA). The first block, PEO, is prepared by anionic polymerization of ethylene oxide in tetrahydrofuran. End capping is achieved by treatment of living PEO chain ends with 2‐bromoisobutyryl bromide to yield a macroinitiator for ATRP. The second block is added by polymerization of HMA, using the PEO macroinitiator in the presence of dibromobis(triphenylphosphine) nickel(II), NiBr₂(PPh₃)₂, as the catalyst. Kinetics studies reveal absence of termination consistent with controlled polymerization of HMA. GPC data show low polydispersities of the corresponding diblock copolymers. The microdomain structure of selected PEO‐block‐PHMA block copolymers is investigated by small angle X‐ray scattering experiments, revealing behavior expected from known diblock copolymer phase diagrams.

SAXS diffractograms of PEO‐block‐PHMA diblock copolymers with 16, 44, 68 wt.‐% PEO showing spherical (A), cylindrical (B), and lamellae (C) morphologies, respectively.     

Synthesis of Poly(ethylene terephthalate)‐block‐Poly(tetramethylene oxide) Copolymer by Direct Polyesterification of Reactive Oligomers

The object of this study was the synthesis of thermoplastic elastomer compounds by direct copolyesterification of reactive oligomers of poly(ethylene terephthalate) (PET) and of poly(tetramethylene oxide) (PTMO). PET was glycolysed to synthesise hydroxytelechelic oligomers of PET. Commercially available hydroxytelechelic PTMO was modified to synthesise carboxytelechelic oligomers. The chemical structures of these oligomers were investigated by ¹H NMR and size exclusion chromatography. Multiblock poly(ester‐ether) was then obtained by polyesterification of the hydroxytelechelic and carboxytelechelic oligomers, using different catalysts and different reaction conditions. The best stoichiometric ratio was determined to lead to the highest M _n. The chemical structure of the synthesised poly(ester‐ether) was investigated by size exclusion chromatography and ¹H NMR. The thermal and thermomechanical behaviour of the synthesised poly(ester‐ether) was investigated by differential scanning calorimetry and by dynamic mechanical analysis, and showed a thermoplastic elastomer behaviour. This product could also be an interesting way of chemically recycling PET waste.

Polyesterification of hydroxytelechelic PET with carboxytelechelic PTMO.     

Fine Structures in the Spherulites of Regioregular Poly(3‐dodecylthiophene)

Summary: In this work, we employed various techniques to cooperatively characterize the crystalline structure and morphology of a regioregular poly(3‐dodecylthiophene). We observed the spherulites in casting films first by polarized light microscopy and then further studied the fine structures within the spherulites by scanning and transmission electron microscopy. These studies showed that the stripe‐like structures with a width of ≈20 nm and a length of 100–500 nm are the basic building blocks of the spherulites. The small‐angle X‐ray scattering and wide‐angle X‐ray diffraction studies further confirm the existence of such the structures. Considering the stiff and unfolding feature of the macromolecules, we believe that the stiff macromolecules may adopt a special way to form the fine structure: the orientation of stiff macromolecules parallel to the longitudinal direction of the stripes without any chain folding.

     

Protonation of Sulfonated Poly(4,4′‐diphenylether‐1,3,4‐oxadiazole) Membranes

This work describes the effect of sulfuric acid protonation on the properties of SPOD‐DPE membranes using FT‐IR and impedance spectroscopic analyses. The IR spectra showed the protonation of nitrogen atoms from oxadiazole rings, with a broad band complex in the region 3 000–2 100 cm^?1 with two centered peaks at 2 590 and 2 440 cm^?1. The S?O characteristic absorption bands in SPOD‐DPE and sulfuric acid were specially studied in the region of 1 800–900 cm^?1. The band shifts are associated to the interaction between acid groups and oxadiazole ring nitrogen atoms. The IR spectra evidenced the presence of three absorption species (HSO, SO and free H₂SO₄) depending on the sulfuric acid concentration. For the protonated SPOD‐DPE membranes, a proton conductivity around 10 mS · cm^?1 was reached at 50 °C.