四种树脂水门汀黏结牙本质剪切强度的比较

目的:评价4种树脂水门汀与牙本质黏结剪切强度。方法:新鲜拔除的无龋损人第三磨牙48个,随机分为4组(n=12),制备颊侧牙本质黏结面,分别与4种树脂水门汀(Unicem、Panavia F、VariolinkⅡ、Vitique)黏结处理,测试剪切强度,SEM观察牙本质黏结界面。结果:4种树脂水门汀中RelyX Unicem(12.84±2.29)MPa与Panavia F(14.93±3.73)MPa、Vitique(11.03±2.57)MPa之间无显著性差异(P>0.05),而他们均显著高于VariolinkⅡ(5.43±1.25)MPa(P<0.05)。结论:新型自黏结树脂水门汀RelyX Unicem可以取得与牙本质良好的黏结效果,且美观,易于使用,节省操作时间,为黏结修复体提供了一种新的选择。     

Effect of temporary cements on the microtensile bond strength of self-etching and self-adhesive resin cement

Objective. The aim of this study was to evaluate the microtensile bond strength (µTBS) of self-etching and self-adhesive resin cement systems to dentin affected by the presence of remnants of either eugenol-containing or eugenol-free temporary cements. Materials and methods. Thirty extracted teeth were obtained and a flat dentin surface was exposed on each tooth. Acrylic blocks were fabricated and cemented either with one of two temporary cements, one zinc oxide eugenol (ZOE) and one eugenol free (ZOE-free), or without cement (control). After cementation, specimens were stored in water at 37°C for 1 week. The restorations and remnants of temporary cements were removed and dentin surfaces were cleaned with pumice. Resin composite blocks were cemented to the bonded dentin surfaces with one of two resin cements, either self-etching (Panavia F 2.0) or self-adhesive (RelyX U-100). After 24 h, the specimens were sectioned to obtain beams for submission to µTBS. The fracture mode was evaluated under a stereoscopic loupe and a scanning electron microscope (SEM). Data from µTBS were submitted to two-way repeated-measure ANOVA and the Tukey test (alpha = 0.05). Results. The cross-product interaction was statistically significant (p < 0.0003). The presence of temporary cements reduced the bond strength to Panavia self-etching resin cements only (p < 0.05). Fracture occurred predominantly at the dentin–adhesive interface. Conclusions. The presence of eugenol-containing temporary cements did not interfere in the bond strength to dentin of self-adhesive resin cements.     

不同根管牙本质表面处理对树脂水门汀粘接强度的影响

目的 比较不同根管牙本质表面处理对树脂水门汀粘接强度的影响.方法 24颗单根管离体前磨牙在釉牙骨质界处截冠后行根管充填,实验随机分为四组:A组为对照组(无表面处理);B组为冲洗处理组(17％EDTA 10ml和5％NaClO10ml联合冲洗根管各30s);C组为酸蚀处理组(35％磷酸酸蚀根管30s);D组为冲洗+酸蚀处理组(先17％EDTA10ml和5％NaClO10ml联合冲洗根管各30s;后用35％磷酸酸蚀根管30s).用PULPDENT树脂水门汀进行粘接.自凝塑料包埋牙根,切割为1 mm厚的试件,并将其按照根管的深度分为根尖、根中、根冠3组,测试其粘接强度.记录数值并进行统计分析.结果 与A组相比,B组、C组和D组冲洗桩道后,三个区段的根管牙本质与树脂水门汀的粘接强度均明显增加,差异有统计学意义(P＜0.01),其中以D组的粘接强度最高,D组根尖段与其他两段间的粘接强度差异有统计学意义(P＜0.01);三组实验组的根中段和根冠段之间差异没有统计学意义(P＞0.05).无论是对照组还是实验组,根尖段牙本质与树脂水门汀的粘接强度均为最低,根冠段最高,且差异具有统计学意义(P＜0.01).结论 (1)采用冲洗处理、酸蚀处理和冲洗+酸蚀处理根管壁均能增强根管牙本质与树脂水门汀的剪切粘接强度;(2)根管部位对根管牙本质与树脂水门汀的剪切粘接强度有影响.     

Effects of dentin surface treatments including Er,Cr:YSGG laser irradiation with different intensities on the push-out bond strength of the glass fiber posts to root dentin

Abstract

Objective. Intra-canal post systems are commonly used to restore root-filled teeth. Bond strengths of the posts can be affected by various surface treatments of the post or the dentin. The aim of this study was to evaluate the effects of dentin surface treatments including erbium-chromium; yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser irradiation with different intensities on the push-out bond strength of the glass fiber posts to root dentin. Materials and methods. Forty single-rooted human maxillary incisors were filled and post spaces were prepared. After these procedures, the specimens were divided randomly into four groups according to the dentin surface treatments, as follows: (i) untreated surface (control), (ii) 1W Er,Cr:YSGG laser application, (iii) 2W Er,Cr:YSGG laser application and (iv) 3W Er,Cr:YSGG laser application. Then the posts were cemented into the root canals using dual-cured resin cement. Bonded specimens were cut into 1-mm-thick slices and push-out tests were performed using a universal testing device. All specimens were loaded until fracture and the failure modes were evaluated with a stereomicroscope at 32× magnification. Representative specimens were analyzed by scanning electron microscopy. Data were analyzed using a one-way ANOVA, Tukey and Wilcoxon tests. Results. The bond strength values ranged from 3.22–4.68 MPa. There were no statistically significant differences among the groups, regardless of the different levels. The coronal and middle levels of the post space had significantly higher bond strength values compared with the apical level (p < 0.05). Conclusion. Er,Cr:YSGG laser irradiation with different intensities did not increase the bond strength of the fiber posts to the root canal dentin walls.     

2种树脂黏固剂产品与人牙本质黏结性能的研究

目的探讨2种树脂黏固剂对进行和不进行处理的人牙本质是否具有相同的黏结效果。方法将30枚人牙本质试件分为6组,分别施以不同表面的处理（A、B组不处理 C、D组磷酸酸蚀15s E、F组磷酸酸蚀15s后使用One-step通用型黏结剂）。A、C、E组使用RelyX Unicem双固化树脂黏固剂,B、D、F组使用Bis-cem双固化树脂黏固剂,制作牙本质/树脂黏固剂黏结试件,测试剪切黏结强度,扫描电镜观察黏结界面形态。结果统计分析可知组A和组B的黏结强度值分别低于组C、E和组D、F,组C与组E间以及组D与组F间无统计学差别。RelyX Unicem树脂黏固剂除对于磷酸酸蚀牙本质的黏结强度高于Biscem树脂黏固剂外,牙本质进行其他表面处理或不处理时,2种树脂黏固剂间的黏结强度无明显差别。结论磷酸酸蚀能够提高RelyX Unicem和Biscem2种自黏结树脂黏固剂对牙本质的黏结强度。     

Influence of different drying methods on microtensile bond strength of self-adhesive resin cements to dentin

Objective. This study investigated the effect of different drying methods of dentin surface on the bonding efficacy of self-adhesive resin cements (SRCs). Materials and methods. Three SRCs (RelyX U200, RU; Maxcem Elite, ME; and BisCem, BC) and one resin-modified glass ionomer cement (RelyX Luting 2, RL) were used. The characteristics of the materials were evaluated using thermogravimetric analysis and surface roughness and contact angle measurements. Human dentin surfaces were finished with 600-grit silicon carbide paper and assigned to three groups according to these drying methods: ethanol dehydration, drying by waiting for 10 s after blot-drying and blot-drying. The four cements were used for luting composite overlays to the dried dentin. After 24 h storage at 37°C and 100% relative humidity, stick-shaped specimens with a cross-sectional area of 0.8 mm² were prepared and stressed to failure in tension at a crosshead speed of 0.5 mm/min (n = 27). Failure modes of fractured specimens were assessed by optical and scanning electron microscopy. Results. RL was the most hydrophilic, followed by BC and ME and then RU. All the luting cements luted to ethanol-dehydrated dentin showed zero bond strengths. For the three SRCs, drying by waiting produced higher microtensile bond strengths than blot-drying. RU showed the best bonding performance in the above two dentin conditions. RL showed significantly higher bond strength in blot-drying condition than in drying-by-waiting (p < 0.001). Conclusions. This study suggests that dentin surface moisture has a crucial effect on the bond strength of SRCs.     

根管冲洗液对根管壁黏结强度影响的研究进展

完善的根管治疗是桩核冠修复的基础,根管冲洗是其中不可缺少的步骤.但常规使用的一些根管冲洗液可能对后期修复过程中黏结材料与根管壁间的黏结强度产生影响.本文就此类研究的进展情况作一综述.     

Nd: YAG激光对3种树脂水门汀与牙本质粘接强度的影响

目的观察Nd: YAG激光照射前后树脂水门汀-牙本质粘接界面的微观形貌特征,评价Nd: YAG激光对3种树脂水门汀与牙本质间粘接强度的影响。方法选择人离体前磨牙30颗,分为颊、舌两部分,将试件随机分为激光组和对照组。激光组以0.8 W、10 Hz脉冲Nd: YAG激光作用于牙本质表面25 s,联合3种树脂水门汀RelyX ARC、Panavia F和RelyX Unicem充填;对照组直接使用树脂水门汀充填。然后测试剪切强度,在根管显微镜下观察断裂模式并分类。另选人离体前磨牙6颗,按照标准的牙本质粘接面预备后,使用Nd: YAG激光照射3颗牙牙本质表面,并联合充填不同的树脂水门汀,用扫描电镜观察Nd: YAG激光照射前后树脂水门汀-牙本质界面的微观形貌变化。结果
激光照射可以提高自酸蚀树脂水门汀Panavia F和自粘接树脂水门汀RelyX Unicem与牙本质之间的剪切强度（P＜0.05）。激光会降低全酸蚀树脂水门汀RelyX ARC与牙本质间的剪切强度（P＜0.05）。根管显微镜下观察可见：试件断裂大部分发生在树脂水门汀-牙本质界面。扫描电镜观察可见：Nd: YAG激光照射后,全酸蚀亚组和自酸蚀亚组的混合层变薄、树脂突变短且少;自粘接亚组变化不明显,未见树脂突。结论Nd: YAG激光照射后,可提高Panavia F和RelyX Unicem与牙本质的剪切强度,建议临床联合应用。     

氧化锆陶瓷与三种树脂粘接剂粘接剪切强度比较

目的探讨适合牙科氧化锆陶瓷的粘接材料。方法将烧结后的氧化锆陶瓷片分为3组,每组32片,分别采用三种自酸蚀粘接剂RelyX Unicem、PanaviaTM F、Superbond C﹠B与喷砂后的氧化锆陶瓷片粘接,水浴24h和水浴30d后,测试其粘接剪切强度。数据用SAS9.12软件进行统计学分析,粘接断面用扫描电镜观察。结果 PanaviaTMF树脂粘接材料粘接强度最好,分别为（31.36±3.49）MPa（水浴24h）、（29.52±3.44）MPa（水浴30d）。Superbond C﹠B能够取得较好的初期粘接强度（31.85±3.61）MPa（水浴24h）,但水浴30d后明显下降至（21.32±2.58）MPa,P〈0.05。RelyX Unicem的初期（水浴24h）粘接强度最小为（13.29±3.05）MPa,P〈0.0001,但水浴30d后粘接强度为（12.06±2.28）MPa,未见明显降低,P（0.05。结论含有MDP磷酸单体的树脂粘接材料可以使牙科氧化锆陶瓷获得最好的粘接效果。使用不含无机填料的化学固化型纯树脂粘接剂可以取得较好的初期粘接强度但长期效果欠佳。一步法自酸蚀树脂粘接剂虽然没有很高的初期粘接强度,但粘接效果尚能持久。     

牙本质玷污层特性对自粘接树脂水门汀粘接强度的影响

目的 评价牙本质表面玷污层的特性对自粘接型树脂水门汀粘接强度和耐久性的影响。方法 将48颗新鲜无龋的人第三恒磨牙暴露出牙本质表面,分别用标准粒径（105~125 μm）金刚砂车针（A组）和标准粒径+细粒径（25 μm）金刚砂车针进行研磨（B组）。研磨后的牙齿分别与Clearfil SA Cement（CSA）和Multilink Speed（MS）两种自粘接型复合树脂水门汀粘接,制成微拉伸试件,试件分别在水中存储24 h和2年,进行微拉伸强度测试,断裂后的试件使用体视显微镜观察粘接界面并记录断裂模式。采用扫描电子显微镜（SEM）观察研磨后的牙本质表面及牙本质-树脂粘接界面。结果 A组SEM观察到研磨后牙本质表面粗糙,玷污层较厚,牙本质小管口未完全栓塞;B组牙本质表面粗糙程度降低,牙本质小管口完全栓塞,玷污层变薄。CSA和MS的B组初期粘接强度显著低于A组（P<0.05）;CSA和MS的粘接强度在水储存2年后出现显著降低（P<0.05）,CSA的B组粘接强度显著低于A组（P<0.05）,而MS的A组与B组间的粘接强度无明显差异（P>0.05）。结论 牙本质表面玷污层特点及自粘接型树脂水门汀类型都会对粘接强度及耐久性产生影响。     

Bond strength of adhesive cements to root canal dentin tested with a novel pull-out approach

Introduction

A novel approach to the pull-out test using silica-coated and silanized steel spreaders was designed to avoid influence from the post-cement interface. In this study, this test was applied to compare the post retention of adhesive versus conventional cements.

Methods

Canals of 90 single-rooted human teeth were prepared to size 60 taper .02; trimmed to an 8-mm root canal length; irrigated with 40% citric acid, 3% NaOCl, and 70% ethanol; and randomly divided into 9 groups (n = 10). Steel spreaders (size 55, taper .02) were silica coated and silanized with the Rocatec system (3M-Espe, Seefeld, Germany), except for a control group using GCem, and cemented with one of these adhesive luting materials (RelyX Unicem [3M-Espe], Clearfil SA Cement [Kuraray Medical, Okayama, Japan], Bifix SE [Voco GmbH, Cuxhaven, Germany], NX3 [Kerr, Orange, CA], GCem [GC Corp, Tokyo, Japan], or SmartCem2 [Dentsply De Trey GmbH, Konstanz, Germany]) or conventional cements (Hoffmann’s cement [Hoffmann Dental Manufaktur GmbH, Berlin, Germany] or Ketac Cem [3M-Espe]). After storage in distilled water (24 h/37°C), the spreaders were pulled out in a universal testing machine at a crosshead speed of 2 mm/min.

Results

The failure mode was cohesive or adhesive at the cement-dentin interface in more than 80% of the experimental samples (control group: adhesive to the post: 9/10 samples). Adhesive luting materials retained posts better than conventional cements (t test, P < .001) but with a wide range in variation. RelyX Unicem displayed significantly higher values except when compared with Bifix SE and Clearfil SA (analysis of variance/Student-Newman-Keuls, P < .05). NX3, SmartCem2, and GCem showed no significant differences to Hoffmann’s cement and Ketac Cem.

Conclusions

The novel pull-out approach served well in testing the bond strength of different cements to root canal dentin. The bonding effectiveness of adhesive cements varied significantly and was material specific.     

自酸蚀树脂水门汀ResiCem牙本质粘结强度的评价

目的 评价自酸蚀树脂水门汀ResiCem的牙本质粘结强度并探讨酸蚀对其粘结强度的影响。方法 选择离体无龋第三恒磨牙15颗。沿垂直于牙体长轴方向将磨牙冠中1/3处切开,将牙本质面分别用自酸蚀树脂水门汀Panavia F和Resi-Cem原位对位粘结。其中ResiCem组牙本质面分别用磷酸酸蚀0、5、10、15 s。用低速切片机把样本切割成约1 mm×1 mm×8mm条块后进行微拉伸测试,并通过扫描电镜观察粘结界面。结果 ResiCem的牙本质微拉伸粘结强度[(16.9±5.3)MPa]与Panavia F[(17.0±5.2)MPa]间差异无统计学意义(P>0.05)。磷酸酸蚀显著地降低ResiCem与牙本质间的粘结强度(P<0.05),并随着酸蚀时间的延长而降低。结论 ResiCem的牙本质微拉伸粘结强度与Panavia F相当,但酸蚀会降低ResiCem的牙本质粘结强度。     

Analysis of resin tags formation in root canal dentine: a cross sectional study

Aim  To evaluate the length, density and quality of resin tags formed by penetration of various types of adhesive systems into dentinal tubules at various cross section levels of the root canal in correlation to the density of dentinal tubules.
Methodology  Thirty mandibular premolars were instrumented and fibre posts were inserted with three different adhesive systems with and without activator: etch & rinse XP Bond and XP Bond/Self Cure Activator; self-etch (two-step) AdheSE and AdheSE/AdheSE DC Activator and self-etch (one-step) Hybrid Bond and Hybrid Bond/Hybrid Brushes. The resin tags were evaluated from slices obtained from sections perpendicular to the long axis of the teeth at 3, 6, and 9 mm from the root apex under a Confocal Laser Scanning microscope.
Results  In all groups, lack of continuity of resin tag length, density and quality was observed not only from the cervical to the apical region of each root canal, but also in a mesio-distal direction to the long axis of the root. Application of etch & rinse adhesive in contrast to the self-etch adhesives provided the formation of the shorter, but considerably denser, more homogeneous and not interrupted resin tags with similar length. Use of the activator for all types of adhesives significantly increased the completeness ( P  = 0.014) and continuity ( P  = 0.024) of resin tags.
Conclusions  None of the investigated adhesives were able to completely infiltrate the dentinal tubules in the entire root canal. Use of the etch & rinse adhesive system and the activators significantly increased the density and the quality of resin tags.     

Bond strength of fibre glass and carbon fibre posts to the root canal walls using different resin cements

The aim of the study was to evaluate the bond strength of fibre glass and carbon fibre posts in the root canal walls cemented with self-adhesive (RelyX-Unicem) and chemical (Cement-Post) resin cements. Forty maxillary canines were divided into four groups according to the cement and post used and submitted to the push-out test (0.5 mm min(-1)). The data were submitted to statistical analysis (2-way ANOVA, Bonferroni--P<0.05) and fracture analysis by Scanning Electronic Microscopy. Fibre glass presented the best results when cemented with RelyX-Unicem and Cement-Post (P<0.05). RelyX-Unicem presented the highest bond strength values for both posts (P<0.05). Fracture analysis showed predominance of cohesive fracture of post for RelyX-Unicem and adhesive fracture between dentin/cement and mixed for Cement-Post. The bond strength values were significantly affected by the type of post and cement used and the highest values were found for fibre glass posts and RelyX-Unicem.     

Effects of luting agent and thermocycling on bond strengths to root canal dentine

AIM: To investigate the effects of luting agent and thermocycling on bond strengths to root canal dentine. METHODOLOGY: Extracted maxillary canines (n =144) were root filled and divided into six groups of 24 teeth each. Fibre posts (FRC Postec) were inserted using six luting agents: Panavia F, Multilink, Variolink II, PermaFlo DC, RelyX Unicem and Clearfil Core. Each root was sliced into six discs (thickness 1 mm) representing the coronal, middle and apical part of the root canal. Push-out tests were performed 24 h after post insertion (n = 12) as well as after thermocycling (5000x; 5-55 degrees C, 30 s) (n = 12). Statistical analysis was conducted using analysis of variance (anova) followed by post-hoc comparisons (Tukey-B). The influence of thermocycling on bond strengths was investigated for each material and region separately using t-tests. RESULTS: The bond strengths were significantly affected by the luting agent (P < 0.001), the root position (P = 0.003) and thermocycling (P < 0.001; three-way anova). RelyX had significantly higher bond strengths compared with all other materials (P < 0.05; Tukey-B). The apical region of the root canal had significantly higher bond strengths compared with the middle and coronal region (P < 0.05; Tukey-B). After thermocycling for RelyX a significant increase in bond strengths was detected for the middle and apical region (P < 0.01; t-test, Bonferroni factor 18). CONCLUSIONS: Bond strengths were affected significantly by luting agent and root position. RelyX had higher bond strengths compared with other materials. The apical region of the canals was characterized by significantly higher bond strengths.     

酸蚀对自黏结树脂水门汀与牙本质黏结强度的影响

目的:评价酸蚀预处理对自黏结树脂水门汀Unicem、G-Cem、Clearfil SA Cement、BisCem与牙本质微拉伸黏结强度的影响。方法:选用人无龋离体第三恒磨牙32颗,用低速切片机将选用磨牙冠1/4处沿垂直于牙体长轴方向切开,暴露牙本质。实验组在牙本质表面涂布37%磷酸,冲洗、吹干,对照组不做处理。然后将各组与直径为5 mm、高为4 mm的树脂块分别用 Unicem、G-Cem、Clearfil SA Cement、BisCem进行黏结。水浴24 h后,用低速切片机将样本切割成约1 mm×1 mm×8 mm条状,再进行微拉伸测试,并通过扫描电镜观察黏结界面。采用SPSS16.0软件包对数据进行统计学分析。结果:Unicem组（12.9±3.2） MPa、G-Cem组（11.7±2.6） MPa及Clearfil SA Cement组（10.9±2.3） MPa与牙本质的微拉伸黏结强度显著高于BisCem组（6.8±2.4） MPa（P<0.05）。酸蚀预处理后,Unicem组（9.2±2.5） MPa、G-Cem组（6.1±2.3） MPa及Clearfil SA Cement组（4.8±1.7） MPa黏结强度显著降低（P<0.05）,而BisCem组（7.1±2.9） MPa黏结强度无显著差异。结论:牙本质的表面酸蚀预处理降低了自黏结树脂水门汀G-Cem、Clearfil SA Cement及Unicem 的牙本质黏结强度,但对BisCem的牙本质黏结强度无显著影响。     

树脂类粘接剂对全瓷与牙本质之间粘接强度的影响

目的比较3种不同粘接剂对3种全瓷材料与牙本质之间抗剪切粘接强度的影响。方法样本为热压铸造陶瓷组、氧化铝渗透陶瓷组和氧化锆切削陶瓷组,每组各18片,各组再随机分为A、B、C3个小组,每小组6片。将收集的离体恒磨牙打磨至牙本质浅层,分别采用树脂类粘接剂RelyXTM ARC、PanaviaTMF以及Rely XTM Unicem与3种全瓷片粘接。所有试件均置于37℃人工唾液,24h后测试54个试件的抗剪切强度。结果热压铸造陶瓷组与氧化锆切削陶瓷组均为RelyXTM Unicem抗剪切粘接强度最高,而氧化铝渗透陶瓷组PanaviaTM F抗剪切粘接强度最高。结论对于3种不同全瓷材料,临床上可根据全瓷修复体的种类选择适当的粘接剂系统。     

氧化物陶瓷与3种树脂水门汀初期粘接强度比较

目的:通过对2 种修复用氧化物陶瓷与3 种树脂水门汀的粘接抗剪强度比较,探讨适合牙科氧化物陶瓷的粘接材料.方法: 分别用3 种树脂水门汀Superbond C&B、RelyX~(TM)Unicem、Panavia~(TM) F与喷砂后的氧化锆(ZrO2)及三氧化二铝(Al_2O_3)陶瓷的粘接面粘接,37 ℃水浴24 h后测试其粘接抗剪强度,数据用SAS 9.12 软件进行统计学分析.结果: Al_2O_3陶瓷组间均有显著性差异(P<0.000 1), Superbond C&B粘接强度最高为(37.60±2.06) MPa. ZrO2陶瓷组中Superbond C&B与Panavia~(TM) F的粘接强度差异无显著性(P>0.05),RelyX~(TM)Unicem粘接强度最低为(13.29±3.05) MPa.结论: Superbond C&B、Panavia~(TM) F与氧化物陶瓷均具有较高的粘接强度,一步法自酸蚀粘接剂RelyX~(TM)Unicem虽然操作简便、提高了工作效率,但不如多步法系统获得的粘接强度大.     

不同剂型玻璃离子水门汀对牙本质粘结剪切强度的比较

目的:比较不同剂型玻璃离子水门汀对牙本质粘结剪切强度,为临床使用提供参考。方法:临床收集新鲜拔除的磨牙30个,用慢速精密齿科片切机切取颊面浅层牙本质薄片(片厚2 mm),自凝塑料包埋,仅暴露颊侧浅层面作为粘结面,流水冲洗4 s,无油气体吹干,于每个试件的粘结面上固定一直径4 mm,高2 mm成型管。然后将30个试件随机分为3组(每组10个),分别使用RelyXTM Luting Cement(粉液剂型)、GC Fuji PLUS(粉液剂型)和GC Fuji CEM(双糊剂型)3种玻璃离子水门汀进行充填,制作粘结试件后,试件置于盛有人工唾液的容器中37℃24 h,用万能测试机测定每个试件的粘结剪切强度。结果:3种玻璃离子水门汀的粘结剪切强度由底到高分别为:RelyXTM Luting Cement(粉液剂型)(6.163±1.177)MPa、GC Fuji PLUS(粉液剂型)(8.004±0.962)MPa、GC Fuji CEM(双糊剂型)(10.31±0.893)MPa,三者间差异有统计学意义(P<0.05)。结论:双糊剂型玻璃离子水门汀抗粘结剪切强度明显高于两种粉液剂型玻璃离子水门汀,是临床修复治疗的良好选择。     

偶联剂和不同粘接剂对纤维桩粘接强度的影响

目的:利用薄片推出实验比较硅烷偶联剂和三种树脂粘接剂对纤维桩剪切粘接强度的影响.方法:60颗因牙周病等原因拔除的上颌单根前牙,根管治疗后行纤维桩修复的桩道预备.随机分为5组,每组12颗牙.分别采用下列粘接剂粘接Matchpost纤维桩:A组:Paracore粘接剂+偶联剂;B组:Paracore粘接剂;C组:Panavia F粘接剂+偶联剂;D组:Panavia F粘接剂;E组:Multilink N粘接剂+偶联剂.纤维桩粘接后,在牙根中部横向切割1.0mm层厚切片2个,在Zwick Z100材料试验机上行薄片推出试验(Push-Out Bond Test),记录失败载荷,计算剪切粘接强度,体视显微镜观察粘接失败类型.结果采用SPSS 11.5进行方差分析和χ2检验.结果:五组样本的剪切粘接强度(MPa)分别为A组:14.69±2.76;B组:9.46±3.11;C组:13.12±3.10;D组:10.40±3.30;E组:13.86±3.81,方差分析提示五组间差异有统计学意义(P <0.01).采用偶联剂处理时,Paracore粘接剂和Panavia F粘接剂与纤维桩间的剪切粘接强度均高于未用偶联剂处理者(P <0.05).采用偶联剂处理时,三种树脂粘接剂与纤维桩的剪切粘接强度间差异无统计学意义(P >0.05).五组粘接失败类型间差异有统计学意义(P <0.05),未采用硅烷偶联剂处理纤维桩表面者,出现纤维桩-粘接剂界面失败者增多.结论:在树脂粘接前,玻璃纤维桩表面氢氟酸酸蚀后,采用硅烷偶联剂处理可显著提高纤维桩与树脂粘接剂间的剪切粘接强度.