Long-term results of uncemented acetabular cups with an ACS polyethylene liner. A 14–16-year follow-up study

We assessed the clinical and radiographic results of 40 porous-coated acetabular cups with an Acetabular Cup System polyethylene liner over a minimum 14-year follow-up. Femoral head penetration was estimated using a software package. Fifteen cups were revised, 11 due to polyethylene liner rupture. All cups but two were radiographically stable, and 11 hips showed acetabular osteolysis. The overall femoral head penetration rate in hips without liner fracture with reference to the early penetration point was 0.1188+/-0.070 mm per year. Polyethylene liner fractures were associated with higher early femoral head penetration (P<0.0001) and a vertical cup position (P=0.0016). The 14-year survival without cup revision for any reason was 63.9%, 71.8% with no ACS polyethylene liner fracture and 65.3% with no acetabular osteolysis. Most cups showed a good clinical outcome in general, but major Acetabular Cup System liner failure and osteolysis were frequent. Patients with the ACS cups still in place should be monitored closely.     

The Harris-Galante total hip arthroplasty: a minimum 8-year follow-up study

A total of 93 Harris-Galante Porous I (HGP- I) prostheses were analyzed with a mean follow-up of 10.2 years. Thigh pain (28 hips) correlated with unstable fixation (P<.005), female gender (P<.045), young age (P<.05), poor distal femoral fill (P<.002), subsidence (P<.0001), and osteolysis (P<.05). Thirteen stems and 6 metallic shell cups were revised. Kaplan-Meier analysis showed 13-year survival rates of 92.5% +/- 5.8% for the metallic shell cup, 79.7% +/- 13% for the HGP-I cup, and 76.3% +/- 14.0% for the stem. Five polyethylene liners were changed because of wear >1 mm. Radiographic loosening occurred in 8 cups. Radiographic bone ingrowth was present in 54 stems, stable fibrous fixation was present in 24 stems, and unstable fixation was present in 15 stems. The mean polyethylene wear was 0.17 mm/y. Eleven hips (11.8%) had acetabular osteolysis, and 24 (25.8%) had femoral osteolysis, the latter being more frequent in unstable stems (P<.007). The HGP-I metallic cup shows better clinical and radiographic results than the stem, which frequently is associated with pain, unstable fixation, and osteolysis. Excessive polyethylene wear is frequent.     

The Harris-Galante Porous acetabular component at intermediate follow-up

Outcome of the acetabular component in 90 consecutive primary noncemented total hip arthroplasties (THAs) was prospectively studied. The acetabular cup consisted of a hemispherical titanium alloy shell with a titanium fiber-mesh porous coating and a modular polyethylene liner (Harris-Galante Porous-1, Zimmer, Warsaw, Ind). The cup was implanted using line-to-line reaming with adjunctive dome screw fixation. The femoral component consisted of a titanium alloy stem with titanium fiber-mesh porous coating and a 28-mm cobalt-chrome modular head. Mean patient age was 53 years (range: 27-75 years); male:female ratio was 48:42; and mean follow-up was 6 years (range: 4.5-8 years). One acetabular component was revised for aseptic loosening. Of 81 unrevised hips available for follow-up, mean Harris hip score was 57 preoperatively and 96 at final follow-up (72% excellent, 15% good, 1 3% fair, and none poor). Of 61 unrevised hips with adequate radiographic follow-up, radiographic failure (complete periprosthetic radiolucency) was evident in 3 (4.9%) and periacetabular osteolysis in none. Radiographic failure did not correlate with poor clinical outcome. Linear polyethylene wear rate (mean: 0.13 mm/year) did not correlate with age, gender, weight, outcome, or cup abduction angle, but did correlate with the presence of femoral periprosthetic osteolysis (0.18 mm/year with femoral osteolysis versus 0.11 mm/year without; P= .01). This series of porous-coated hemispherical cups demonstrated excellent intermediate-term clinical and radiographic outcome, comparable with similarly favorable results reported by the prosthesis designers. A potentially adverse effect of polyethylene wear on the longevity of a THA was supported by a positive correlation between polyethylene wear rate and femoral osteolysis.     

Experiences with the Plasmacup--early stability, wear, remodelling, and outcome

Whilst advances in cementing technique have led to improvement in the survival of cemented femoral stems in total hip arthroplasty (THA), cup failure due to aseptic loosening remains a major clinical problem. These observations have led to a move away from cemented cup designs, particularly in young patients, towards uncemented implants. The Plasmacup is a hemispherical, press-fit, cementless, titanium-shelled, acetabular component with a polyethylene liner. In this article we review our experience of its pattern of early migration, wear, bone remodelling, and mid-term survival. In 18 cups followed for 2 years in subjects with a mean age at operation of 58 years, the mean total vectorial cup migration was 0.75 mm, and cup orientation remained stable (EBRA method). The mean polyethylene linear wear rate over this period was 0.21 mm/year. In 27 cups followed for 6 months using dual-energy X-ray absorptiometry (DXA), average bone loss was -5%, and the pelvic bone-remodelling pattern was consistent with the rim-loading principle of the cup design. In a clinical review of the outcome of 128 cups in 104 patients with a mean age at operation of 51 years and follow-up of 59 months, we found that 82% of patients had a good or very good Merle D'Aubigne score, and cup survival rate was 98% (Kaplan-Meier). Four cups had small radiographic areas of focal osteolysis and three had been revised (two for recurrent dislocation and one for deep sepsis; none were revised for aseptic loosening). The mean linear wear rate in this series was 0.14 mm/year. In conclusion, the Plasmacup shows satisfactory early stability, a wear rate similar to other uncemented cups, and favourable mid-term clinical function and survival rates.     

Migration of the Duraloc cup after 5 years

The Duraloc cup is a frequently used metal-backed, porous-coated, hemispherical, press-fit acetabular component. Published data on loosening rates are contradictory. In this study we investigated migration patterns with computer-assisted Einzel-Bild-Roentgen-Analyse (EBRA) of 67 Duraloc 100 cups. Cup migration and clinical scores were analysed over a 5-year follow-up period. Median total migration of the Duraloc 100 cup was 1.21 mm at 5 years. Seventy-five percent of implants were radiologically stable at 2 years and 90% at 4 years. One cup loosened aseptically at 60 months, requiring revision. Cup diameters > or = 54 mm migrated significantly more than cups < 54 mm in diameter (p = 0.029 at 4 years). There was a significant correlation between high polyethylene wear and further migrating cups within the first post-operative year (p = 0.035 at 12 months). Our analysis revealed significantly higher wear in males (p = 0.029 at 4 years). Radiological loosening at two years could be calculated using receiver-operating characteristic curve analysis, and 1.2 mm as an adequate threshold value (sensitivity = 100%, specificity = 89%).     

Ten- to 15-Year Clinical and Radiographic Results for a Compression Molded Monoblock Elliptical Acetabular Component

The aim of this study was to report the long-term results from a previously published midterm follow-up of a titanium monoblock, elliptical acetabular component. A total of 258 primary total hip arthroplasties (212 patients) with a monoblock, acetabular component were followed up for a mean period of 11.1 years (10-15). Average yearly wear rate was 0.08 mm/y (0.0009-0.32). Acetabular radiolucencies were present in 6 hips (2.4%); all were nonprogressive and present in acetabular zone I. Acetabular osteolysis was present in 5 patients (5 hips, 1.9%); all cups were stable. Four acetabular components were revised, 3 because of recurrent instability. No acetabular components were revised for polyethylene wear or dissociation, acetabular osteolysis, loosening, or deep infection. This monoblock design demonstrates excellent long-term survival and low rate of osteolysis.     

Ten to twelve-year results with the Zweymüller cementless total hip prosthesis

Between January 1987 and December 1990, 221 Zweymüller cementless total hip arthroplasties were performed in 211 patients with idiopathic osteoarthritis. A total of 136 patients (142 prostheses) were evaluated at a mean follow-up of 134 months (SD 9.5). The study group consisted of 78 Hochgezogen and 64 Stepless stem prostheses, all with a threaded titanium cup and ceramic head. No clinical and radiological differences were found between the 2 stem prostheses. Seven cups had been revised because of aseptic loosening; 17 cups showed radiolucent lines, osteolysis, or migration. Mean linear polyethylene wear of 105 (74%) cups was 0.46 mm (SD 0.27), with an annual wear of 0.04 mm (SD 0.02). Wear did not correlate with pain, cup migration, radiolucent lines, or osteolysis. Cumulative survival was 96%. Zweymüller cementless total hip arthroplasty showed good midterm results.     

全髋关节置换术后聚乙烯内衬磨损的测量及其临床意义

目的以计算机数字化方法计测人工全髋假体二维线性磨损,并探讨磨损程度与长期随访结果的临床相关性。方法利用计算机软件测量股骨头中心相对于髋臼中心的矢量位移,来决定关节面磨损的大小和方向。对 104髋非骨水泥型人工假体进行磨损计测、临床和放射学检查,平均随访时间为 8.4年。结果 14髋股骨或髋臼假体松动,假体松动率为 13.5％。平均线性磨损值为 1.14 mm,磨损率为 0.15 mm/年。聚乙烯磨损与髋臼侧骨溶解及假体松动相关 (P< 0.05)。多因素回归分析未发现磨损和患者年龄、体重、髋杯大小和外展角、活动量水平以及 Harris髋关节评分的相关关系。结论此方法可应用于各种不同设计的人工假体内衬的二维磨损测量。磨损与骨溶解显著相关,并与假体松动互为因果。因此,在进行临床随访、放射学观察的同时,磨损情况也是全面评价全髋置换术临床结果的一个重要指标。     

Eight-year results of hydroxyapatite-coated hip arthroplasty

Ninety hips in 82 patients using Omnifit hydroxyapatite (HA)-coated prosthesis were followed for at least 7 years. All stems were stable at the final follow-up. However, aseptic loosening was found in 8 cups and 6 of them were revised. Two polyethylene wear were treated with inserts exchanged. The mechanical failure rate was 11.4% and the combined failure rate was 14.3% for HA-coated cup. Four other cups with wear and osteolysis without loosening or pain and 2 cups with polyethylene wear without osteolysis were still under observation. Our findings suggest that hip arthroplasties with HA coating on the smooth surface of a titanium cup is not reliable. The mid-term result of HA-coated stem is as good as that of porous-coated stem.     

Cementless total hip arthroplasty using porous-coated Biomet acetabular cups (Hexloc and Ringloc types)

This study examined the mid-term (more than 5 years) results of cementless total hip arthroplasty (THA) using Biomet acetabular cups (locking mechanism: Hexloc type or Ringloc type). A series of 58 patients (70 hips) who had undergone cementless THA at our department were available for inclusion in this study. The average age at surgery was 55.2 years, and the average follow-up was 6 years 10 months. Osteolysis occurred in five cases. In the group with osteolysis, the average annual linear wear was 0.18mm/year, and in the group without osteolysis it was 0.10mm/year. The higher linear wear rate in the osteolysis group was statistically significant compared to that in the nonosteolysis group. The age of the patient was closely related to polyethylene (PE) wear in the Hexloc group but not in the Ringloc group. In the Ringloc group there was no close correlation between the thickness of the PE liner and the average annual linear wear, whereas in the Hexloc group the thicker liner had significantly less annual linear wear. It was thought that PE wear of the Hexloc cup was more susceptible to the age of the patient at surgery and the PE thickness than that of the Ringloc cup owing to several structural differences, such as rotational stability and conformity between the metal cup and the PE liner.     

H/G非骨水泥人工全髋关节置换术后聚乙烯内杯磨损临床研究

目的 对H/G非骨水泥人工全髋关节置换术后聚乙烯内杯的磨损及髋臼周围骨溶解的情况进行总结.方法 我院1991至1995年共进行58例(65髋)H/G非骨水泥人工全髋关节置换,其中35例(40髋)获得10年以上随访.对这35例(40髋)患者获得随访的病例,采用计算机数字化方法测量髋臼聚乙烯内杯的二维线性磨损.结果 35例40髋均有不同程度的磨损,磨损范围2～8 mm,平均磨损为(0.32±0.31)mm/年.10髋聚乙烯磨损超过6 mm,髋臼假体周围的骨溶解严重,并伴有金属假体的移位,其中5髋聚乙烯内杯完伞磨透,金属股骨头与金属髋臼相接触;5髋聚乙烯内杯磨损严重伴明显骨溶解,内杯松动.2髋聚乙烯内杯脱位.共实施翻修手术12例,包括更换聚乙烯内杯和金属股骨头2例、金属闩杯翻修2例、全髋翻修8例.28髋在髋臼侧发现骨溶解,其中14髋股骨侧亦有骨溶解发生.结论 本组病例所观测到的H/G髋臼聚乙烯内杯的磨损程度超过文献所报道,而且由于磨损产生的大量磨屑,导致假体周围出现明显骨溶解,直接影响到假体的稳定.关节置换术后应定期随访,避免出现严重骨溶解后增加翻修手术的困难.     

Correlation of wear debris-induced osteolysis and revision with volumetric wear-rates of polyethylene: A survey of 8 reports in the literature

This survey focused on clinical reports of polyethylene wear and osteolysis in total hip replacements. With regard to documentation of clinical wear-rates, 57 publications were reduced to an analysis of 8 reports of THR series, including the incidence of osteolysis. A direct correlation was found among volumetric wear rates, incidence of osteolysis and revision rates in THR concepts of the 1983-1987 era. As volumetric wear rate increased, the incidence of osteolysis and revision rates increased. With regard to our grading system for volumetric wear, with follow-up in the 4-15 year range, osteolysis was rare in group A (wear = 0-80 mm 3 /year), ranging from 6% to 31% in group B (wear 40-80 mm 3 /year) and from 21% to 100% in group C (wear > 140 mm 3 /year). With regard to cup design, the optimal low-wear group had mainly cemented polyethylene cups with 22 and 28 mm head sizes. The mid-wear group B had metal-backed cemented and uncemented cups, with 28 mm head size, and the high-risk group C had only uncemented, metalbacked cups, with the highest wear in the 32 mm head size. Less than 10 years of follow-up did not distinguish adequately between different designs of THR, except in a few cases which had early failures due to material or design deficiencies. Overall, the cemented all-polyethylene cup combined with the smaller ball head proved to be better.     

Correlation of wear debris-induced osteolysis and revision with volumetric wear-rates of polyethylene: a survey of 8 reports in the literature

This survey focused on clinical reports of polyethylene wear and osteolysis in total hip replacements. With regard to documentation of clinical wear-rates, 57 publications were reduced to an analysis of 8 reports of THR series, including the incidence of osteolysis. A direct correlation was found among volumetric wear-rates, incidence of osteolysis and revision rates in THR concepts of the 1983-1987 era. As volumetric wear rate increased, the incidence of osteolysis and revision rates increased. With regard to our grading system for volumetric wear, with follow-up in the 4-15 year range, osteolysis was rare in group A (wear = 0-80 mm3/year), ranging from 6% to 31% in group B (wear 40-80 mm3/year) and from 21% to 100% in group C (wear > 140 mm3/year). With regard to cup design, the optimal low-wear group had mainly cemented polyethylene cups with 22 and 28 mm head sizes. The mid-wear group B had metal-backed cemented and uncemented cups, with 28 mm head size, and the high-risk group C had only uncemented, metal-backed cups, with the highest wear in the 32 mm head size. Less than 10 years of follow-up did not distinguish adequately between different designs of THR, except in a few cases which had early failures due to material or design deficiencies. Overall, the cemented all-polyethylene cup combined with the smaller ball head proved to be better.     

Pelvic osteolysis relationship to radiographs and polyethylene wear

The relationship of radiographic pelvic osteolysis to computed tomographic (CT) volume and polyethylene wear remains controversial. We evaluated the sensitivity and specificity of radiographs in detecting osteolysis considering CT scan as the true value, in 118 hips with cementless cups. Correlation between osteolysis volume in CT, area of osteolysis in radiograph, and linear wear of polyethylene was assessed. The sensitivity and specificity of anteroposterior radiographs for detection of osteolysis was 57.6% and 92.9%, respectively. Addition of oblique radiographs increased the sensitivity to 64.4% without changing the specificity. The sensitivity increased to 92.8% for lesion more than 1000 mm(3). There was good correlation between 2-dimensional (2D) osteolytic area in radiograph and 3-dimensional (3D) volume (r = 0.74) in CT scan and linear wear of polyethylene showed good correlation with 3D CT volume (r = 0.62) and 2D area in radiograph (r = 0.60). Thus radiographs are useful to screen clinically significant osteolysis.     

Midterm survivorship of a press-fit, plasma-sprayed, tri-spike acetabular component

Press-fit acetabular cups without screw holes can limit migration of particulate wear debris and reduce risk of acetabular osteolysis and device loosening. The Tri-Spike cup (Biomet, Inc, Warsaw, Ind) includes a titanium alloy plasma spray porous surface and does not require screw fixation. We retrospectively examined the incidence of cup loosening and acetabular osteolysis after implantation of 45 cups (44 patients) with mean follow-up of 7.3 years (range, 4-9 years). Only one patient (one cup) had evidence of less than 1 mm of retroacetabular radiolucency at 3 years (nonprogressive), which was found to remain firmly fixed during revision of the aseptically loosened femoral component. No cups were removed or revised at latest follow-up. Projected Kaplan-Meier survivorship at 9 years was 100% for cup loosening/revision and 97.8% for radiolucency.     

Primary Total Hip Arthroplasty With Duraloc Cup in Patients Younger Than 50 Years : A 5- to 7-Year Follow-Up Study

We evaluated the clinical and radiographic results of 67 (64 patients) cementless Duraloc-300 cups for young active patients after a mean follow-up period of 6.2 years. The preoperative mean Harris hip score improved from 46.24 to 96.5 points at 5 years. The survivorship of the cup, using radiographically confirmed aseptic loosening as the end point, was 100% at 5 years. The mean rate of liner wear was 0.125 mm/y (00-0.39 mm/y). Acetabular osteolysis was found in 14% (9 hips) of the 67 hips, and the osteolysis is related to polyethylene wear (P = .0024) and sex (P = .001). Although there was no aseptic loosening of the components, there was a high rate of liner wear of the polyethylene liner and acetabular osteolysis.     

The effect of abduction differences between cup and contralateral acetabular angle on polyethylene component wear.

One hundred forty-two patients who underwent cemented or uncemented hip replacement were studied radiographically to determine acetabular component wear. Mean duration of follow-up was 58 months (range: 35-92 months). Average linear wear was 0.78 mm (range: 0-1.9 mm), and average wear rate was 0.16 mm/year (range: 0-0.45 mm/year). An increased wear rate per year correlated with a discrepancy >18.3 degrees between contralateral acetabular angle and acetabular cup inclination (P<.005). Statistical analysis revealed no significant correlation between cup inclination and polyethylene wear, which was studied without considering the contralateral hip (P>.3). There was no relationship between polyethylene wear and cup design, weight, and initial polyethylene thickness.     

Reduced wear in vitamin E-infused highly cross-linked polyethylene cups: 5-year results of a randomized controlled trial

Background and purpose — Vitamin E-infused polyethylene is a relatively new material in joint arthroplasty; there are no long-term reports, and only few mid-term results. Using radiostereometric analysis (RSA), we primarily determined whether vitamin E-infused highly cross-linked polyethylene (HXLPE/VitE) acetabular cups show less wear than ultra-high molecular weight polyethylene (UHMWPE) acetabular cups at 5 years after total hip arthroplasty (THA). We also assessed whether wear rates correlate with increasing cup inclination angles or cup sizes.Patients and methods — This is a 5-year follow-up of our previously reported randomized controlled trial of 62 patients with 3 years’ follow-up, who received THA with either an HXLPE/VitE or a UHMWPE acetabular cup. At 5 years, 40 patients were analyzed (22 in the HXLPE/VitE and 18 in the UHMWPE group).Results — HXLPE/VitE cups continued to show less cumulative femoral head penetration than UHMWPE cups (HXLPE/VitE: 0.24 mm, UHMWPE: 0.45 mm; p < 0.001). Distribution of wear was also more even with HXLPE/VitE cups than with UHMWPE cups (p = 0.002). Moreover, the difference in PE wear between 1 and 5 years in both groups showed no statistically significant correlation with increasing cup inclination angles or cup sizes. Finally, no osteolysis and implant loosening occurred, and no revision surgeries were required.Interpretation — Wear rates continue to be lower in HXLPE/VitE cups than in UHMWPE cups at 5 years of follow-up without correlation with increasing cup inclination angles or cup sizes. Finally, HXLPE/VitE cups may have the potential to prevent osteolysis and implant loosening.

Wear of the polyethylene (PE) component of total hip arthroplasties (THA) may result in osteolysis (Callary et al. 2015). Therefore, attempts such as cross-linking using irradiation and addition of vitamin E have been made to improve the wear properties of PE (Galea et al. 2019). Vitamin-E infused highly cross-linked polyethylene (HXLPE/VitE) has been developed to reduce the number of free radicals without compromising the mechanical properties. There are 2 methods of incorporating vitamin E into PE. The 1st is to blend vitamin E with PE powder before consolidation and. Once consolidated, the blend can be irradiated for sterilization or cross-linking. The 2nd is diffusion of vitamin E into the PE after radiation cross-linking: after PE is irradiated for cross-linking, it is diffused with vitamin E, then machined into its final form and gamma sterilized (Oral et al. 2005). Gamma irradiation causes crosslinking of UHMWPE, which changes its property from the original. However, it causes reduction in tensile strength and elongation of UHMWPE, and leads to long-lived free radicals that react with oxygen (Oral et al. 2007).As HXLPE/VitE is a relatively new material in orthopedic surgery, studies on its wear properties with longer follow-up periods are still limited (Nebergall et al. 2016, 2017, Shareghi et al. 2017, Galea et al. 2019). Our initial 3-year data showed less wear with HXLPE/VitE, which may prevent osteolysis, implant loosening, and eventually revision surgery (Rochcongar et al. 2018). We have now investigated clinical and radiographic outcomes of our previously reported patient cohort at 5-year follow-up. The primary objective is to know whether HXLPE/VitE acetabular cups continue to show less PE wear than ultra-high molecular weight polyethylene (UHMWPE) acetabular cups at 5 years. The secondary objective is to evaluate the correlation between PE wear rates with cup inclination angles or cup sizes, in addition to reporting clinical outcomes.      

Th1 type lymphocyte reactivity to metals in patients with total hip arthroplasty

Introduction

Many kind of hydroxyapatite-coated cups were used, with favorable results in short term studies; it was supposed that its use could improve osteointegration of the cup, enhancing thus stability and survivorship. The purpose of this study is to analyze the long term behavior of the hemispheric HA coated, Dual Radius Osteonics cup and to discuss the way of failure through the exam of the revised components and of both periacetabular and osteolysis tissue.

Materials and Methods

Between 1994 and 1997, at the Department of Orthopedic Sciences of the Insubria University, using the posterolateral approach, were implanted 276 Dual Radius Osteonics^® in 256 patients, with mean age of 63 years.

Results

At a mean follow-up of 10 years (range 8–12 years), 183 cups in 165 patients, were available for clinical and radiographical evaluation. 22 Cups among the 183 were revised (11%). The cause of revision was aseptic loosening in 17 cases, septic loosening in one case, periprosthetic fracture in another case, osteolysis and polyethylene wear in two cases and, finally, recurrent dislocations in the last one. In the remaining patients, mean HHS increased from a preoperative value of 50,15 to a postoperative value of 92,69. The mean polyethylene wear was 1,25 mm (min. 0,08, max. 3,9 mm), with a mean annual wear of 0,17 mm. The mean acetabular migration on the two axis was 1,6 mm and 1,8 mm. Peri-acetabular osteolysis were recorded in 89% of the implants (163 cases). The cumulative survivorship (revision as endpoint) at the time was 88,9%.

Conclusion

Our study confirms the bad behavior of this type of cup probably related to the design, to the method of HA fixation. The observations carried out on the revised cup confirm these hypotheses but did not clarify if the third body wear could be a further problem. Another interesting aspect is the high incidence of osteolysis, which are often asymptomatic becoming a problem for the surgeon as the patient refuses the possibility of a revision.     

Cementless hemispheric acetabular component in total hip replacement

A series of 198 total hip arthroplasties was performed using a porous-coated, hemispheric press-fit cup. One hundred and twenty-seven cups were available for clinical and radiological examination at mean follow-up of 10.6 years. The mean age at the index procedure was 61.2 years. The mean Harris hip score at final follow-up was 89.8. Three cups were revised for aseptic loosening and two liners were changed for eccentric wear and pelvic osteolysis. Nine additional patients showed mild or suspected osteolysis. Two cups were rated "fibrous" stable. There was no correlation between additional screw fixation of the press-fit cup and osteolysis or revision.