Photocatalytic Hydrogen Evolution from Artificial Seawater Splitting over Amorphous Carbon Nitride: Optimization and Process Parameters Study via Response Surface Modeling

Photocatalytic water splitting has garnered tremendous attention for its capability to produce clean and renewable H₂ fuel from inexhaustible solar energy. Until now, most research has focused on scarce pure water as the source of H₂, which is not consistent with the concept of sustainable energy. Hence, the importance of photocatalytic splitting of abundant seawater in alleviating the issue of pure water shortages. However, seawater contains a wide variety of ionic components which have unknown effects on photocatalytic H₂ production. This work investigates photocatalytic seawater splitting conditions using environmentally friendly amorphous carbon nitride (ACN) as the photocatalyst. The individual effects of catalyst loading (X₁), sacrificial reagent concentration (X₂), salinity (X₃), and their interactive effects were studied via the Box–Behnken design in response surface modeling towards the H₂ evolution reaction (HER) from photocatalytic artificial seawater splitting. A second-order polynomial regression model is predicted from experimental data where the variance analysis of the regressions shows that the linear term (X₁, X₂), the two-way interaction term X₁X₂, and all the quadratic terms (X₁₂, X₂₂, X₂₃) pose significant effects towards the response of the HER rate. Numerical optimization suggests that the highest HER rate is 7.16 µmol/h, achievable by dosing 2.55 g/L of ACN in 45.06 g sea salt/L aqueous solution containing 17.46 vol% of triethanolamine. Based on the outcome of our findings, an apparent effect of salt ions on the adsorption behavior of the photocatalyst in seawater splitting with a sacrificial reagent has been postulated.     

The Structural Evolution of Semipolar (11−22) Plane AlN Tem-Plate on m-Plane Sapphire Prepared by Sputtering and High Temperature Annealing

In this work, the epitaxial semipolar (11–22) AlN was prepared on nonpolar m-sapphire substrate by combining sputtering and high-temperature annealing. According to our systematic measurements and analysis from XRD, Raman spectra, and AFM, the evolution of crystalline structure and morphology was investigated upon increasing AlN thickness and annealing duration. The annealing operation intensively resets the lattice and improves the crystalline quality. By varying the film thickness, the contribution from the AlN-sapphire interface on crystalline quality and lattice parameters during the annealing process was investigated, and its contribution was found to be not so obvious when the thickness increased from 300 nm to 1000 nm. When the annealing was performed under durations from 1 to 5 h, the crystalline quality was found unchanged; meanwhile, the evolution of morphology was pronounced, and it means the crystalline reorganization happens prior to morphology reset. Finally, the annealing treatment enabled a zig-zag morphology on the AlN template along the sapphire [0001] direction in the plane, which potentially affects the subsequent device epitaxy process. Therefore, our results act as important experience for the semipolar nitride semiconductor laser device preparation, particularly for the epitaxy of microcavity structure through providing the crystalline evolution.     

Additive Manufacturing of Plastics Used for Protection against COVID19—The Influence of Chemical Disinfection by Alcohol on the Properties of ABS and PETG Polymers

In this paper, the influence of disinfection on structural and mechanical properties of additive manufactured (AM) parts was analyzed. All AM parts used for a fight against COVID19 were disinfected using available methods—including usage of alcohols, high temperature, ozonation, etc.—which influence on AM parts properties has not been sufficiently analyzed. During this research, three types of materials dedicated for were tested in four different disinfection times and two disinfection liquid concentrations. It has been registered that disinfection liquid penetrated void into material’s volume, which caused an almost 20% decrease in tensile properties in parts manufactured using a glycol-modified version of polyethylene terephthalate (PETG).