Investigation of the Geopolymerization Potential of a Waste Silica-Rich Diabase Mud

Diabase mud (DM) is a silica-rich residue yielding from aggregate crushing and washing operations in quarries. This work focuses on identifying the geopolymerization potential of a diabase mud through characterization of its mineralogical composition, investigation of its reactivity, and assessment of the early compressive strengths of alkali activated mixtures formulated based on the mud’s dissolution results. The findings suggest that considerably low amounts of Al and Si metals were dissolved following the dissolution tests conducted on DM, however, the incorporation of small quantities of CEM I, gypsum, and metakaolin (MK) moderately at a Na₂SiO₃:NaOH ratio of 50:50 and with a molarity of NaOH of 4 M enhanced the geopolymerization compared to low L/S ratio mixtures cured at different conditions. When M was increasing, the high L/S ratio mixtures exhibited fluctuations in strengths, especially beyond a 10 M NaOH molarity. Maximum strengths of mixtures at equivalent molarity of 10 were achieved when the Na₂SiO₃:NaOH ratio reached 30:70, regardless of the ambient conditions and the presence of CEM I. The curing conditions, the ratio of Na₂SO₃:NaOH, and the presence of CEM I in the DM-based mixtures did not appear to significantly affect the mixture when NaOH concentration was between 2 M and 4 M; at higher molarities, however, these enhanced the strengths of the geopolymerized DM.     

Drastic Dependence of the pH Sensitivity of Fe2O3-Bi2O3-B2O3 Hydrophobic Glasses with Composition

Fe₂O₃-Bi₂O₃-B₂O₃ (FeBiB) glasses were developed as novel pH responsive hydrophobic glasses. The influence of the glass composition on the pH sensitivity of FeBiB glasses was investigated. The pH sensitivity drastically decreased with decreasing B₂O₃ content. A moderate amount of Fe₂O₃ and a small amount of B₂O₃ respectively produces bulk electronic conduction and a pH response on glass surfaces. Because the remaining components of the glass can be selected freely, this discovery could prove very useful in developing novel pH glass electrodes that are self-cleaning and resist fouling.     

DC and AC Conductivity,Biosolubility and Thermal Properties of Mg-Doped Na2O–CaO–P2O5 Glasses

Bioactive glasses have recently been extensively used to replace, regenerate, and repair hard tissues in the human body because of their ability to bond with living tissue. In this work, the effects of replacing Na₂O with MgO on the electrical, biosolubility, and thermal properties of the target glass 10Na₂O–60P₂O₅–30CaO (in mol%) were investigated. The electrical properties of the glasses were studied with the impedance spectroscopy technique. At 473 K, DC conductivity values decreased from 4.21 × 10⁻¹¹ to 4.21 × 10⁻¹² S cm⁻¹ after complete substitution of MgO for Na₂O. All samples had a similar activation energy of the DC conduction process ~1.27 eV. Conduction mechanisms were found to be due to hop of ions: Na⁺, Mg²⁺_, and probable H⁺. FTIR analysis showed that, as the Mg content increased, the Q² unit (PO₂⁻) shifted towards higher wavenumbers. The proportion of Q³ unit (P₂O₅) decreased in the glass structure. This confirmed that the replacement of Na⁺ by Mg²⁺ was accompanied by concurrent polymerization of the calcium–phosphate glass network. The biosolubility test in the phosphate-buffered saline solution showed that the magnesium addition enhanced the biosolubility properties of Na₂O–CaO–P₂O₅ glasses by increasing their dissolution rate and supporting forming CaP-rich layers on the surface. The glass transition temperature increased, and thermal stability decreased substantially upon substitution of Na₂O by MgO.     

Use of Gypsum as a Preventive Measure for Strength Deterioration during Curing in Class F Fly Ash Geopolymer System

This study discusses strength deterioration during the curing process of fly ash geopolymer and the use of CaSO₄·2H₂O (gypsum) as a deterioration remedy when the ash was synthesized using a 10M NaOH and Na-silicate solution. The strength decline was mainly due to the widespread formation of nanometer-sized cracks that were related to excessive Na and Si concentrations at an early age. Use of 2 wt% CaSO₄·2H₂O resulted in the best measured strength by temporarily reducing Na and Si concentrations; Na was absorbed by SO₄²⁻, up to 11% in the matrix within one day, and formed Na₂SO₄ (thenardite), which gradually dissolved over time, slowly releasing Na ions. However, more than 4% gypsum suppressed overall strength development because too many Na ions were locked into Na₂SO₄ and could not participate in geopolymerization. The addition of gypsum impeded glass dissolution and even halted the process when more than 4% gypsum was used.     

Resistance to Sulfuric Acid Corrosion of Geopolymer Concrete Based on Different Binding Materials and Alkali Concentrations

Geopolymer binder is expected to be an optimum alternative to Portland cement due to its excellent engineering properties of high strength, acid corrosion resistance, low permeability, good chemical resistance, and excellent fire resistance. To study the sulfuric acid corrosion resistance of geopolymer concrete (GPC) with different binding materials and concentrations of sodium hydroxide solution (NaOH), metakaolin, high-calcium fly ash, and low-calcium fly ash were chosen as binding materials of GPC for the geopolymerization process. A mixture of sodium silicate solution (Na₂SiO₃) and NaOH solution with different concentrations (8 M and 12 M) was selected as the alkaline activator with a ratio (Na₂SiO₃/NaOH) of 1.5. GPC specimens were immersed in the sulfuric acid solution with the pH value of 1 for 6 days and then naturally dried for 1 day until 98 days. The macroscopic properties of GPC were characterized by visual appearance, compressive strength, mass loss, and neutralization depth. The materials were characterized by SEM, XRD, and FTIR. The results indicated that at the immersion time of 28 d, the compressive strength of two types of fly ash-based GPC increased to some extent due to the presence of gypsum, but this phenomenon was not observed in metakaolin-based GPC. After 98 d of immersion, the residual strength of fly ash based GPC was still higher, which reached more than 25 MPa, while the metakaolin-based GPC failed. Furthermore, due to the rigid 3D networks of aluminosilicate in fly ash-based GPC, the mass of all GPC decreased slightly during the immersion period, and then tended to be stable in the later period. On the contrary, in metakaolin-based GPC, the incomplete geopolymerization led to the compressive strength being too low to meet the application of practical engineering. In addition, the compressive strength of GPC activated by 12 M NaOH was higher than the GPC activated by 8 M NaOH, which is owing to the formation of gel depended on the concentration of alkali OH ion, low NaOH concentration weakened chemical reaction, and reduced compressive strength. Additionally, according to the testing results of neutralization depth, the neutralization depth of high-calcium fly ash-based GPC activated by 12 M NaOH suffered acid attack for 98 d was only 6.9 mm, which is the minimum value. Therefore, the best performance was observed in GPC prepared with high-calcium fly ash and 12 M NaOH solution, which is attributed to gypsum crystals that block the pores of the specimen and improve the microstructure of GPC, inhibiting further corrosion of sulfuric acid.     

Experimental Investigation of Radiation Shielding Competence of Bi2O3-CaO-K2O-Na2O-P2O5 Glass Systems

The gamma-ray shielding features of Bi₂O₃-CaO-K₂O-Na₂O-P₂O₅ glass systems were experimentally reported. The mass attenuation coefficient (MAC) for the fabricated glasses was experimentally measured at seven energy values (between 0.0595 and 1.33 MeV). The compatibility between the practical and theoretical results shows the accuracy of the results obtained in the laboratory for determining the MAC of the prepared samples. The mass and linear attenuation coefficients (MACs) increase with the addition of Bi₂O₃ and A4 glass possesses the highest MAC and LAC. A downward trend in the linear attenuation coefficient (LAC) with increasing the energy from 0.0595 to 1.33 MeV is found. The highest LAC is found at 1.33 MeV (in the range of 0.092–0.143 cm⁻¹). The effective atomic number (Z_eff) follows the order B1 > A1 > A2 > A3 > A4. This order emphasizes that increasing the content of Bi₂O₃ has a positive effect on the photon shielding proficiencies owing to the higher density of Bi₂O₃ compared with Na₂O. The half value layer (HVL) is also determined and the HVL for the tested glasses is computed between 0.106 and 0.958 cm at 0.0595 MeV. The glass with 10 mol% of Bi₂O₃ has lower HVL than the glasses with 0, 2.5, 5, and 7.5 mol% of Bi₂O₃. So, the A4 glass needs a smaller thickness than the other glasses to shield the same radiation. As a result of the reported shielding parameters, inserting B₂O₃ provides lower values of these three parameters, which in turn leads to the development of superior photons shields.     

The Comparison of the Environmental Impact of Waste Mineral Wool and Mineral in Wool-Based Geopolymer

Waste generated in fine wool production is homogeneous and without contamination, which increases its chances of reuse. Waste mineral wool from demolition sites belongs to the specific group of waste. However, the storage and collection require implementing restrictive conditions, such as improper storage of mineral wool, which is highly hazardous for the environment. The study focuses on the leachability of selected pollutants (pH, Cl⁻, SO₄²⁻) and heavy metals (Ba, Co, Cr, Cu, Ni, Pb, Zn) from the waste mineral wool. As a solution to the problem of storing mineral wool waste, it was proposed to process it into wool-based geopolymer. The geopolymer, based on mineral wool, was also assessed regarding the leaching of selected impurities. Rock mineral wool is very good for geopolymerisation, but the glass wool needs to be completed with additional components rich in Al₂O₃. The research involved geopolymer prepared from mineral glass wool with bauxite and Al₂O₃. So far, glass wool with the mentioned additives has not been tested. An essential aspect of the article is checking the influence of wool-based geopolymer on the environment. To investigate the environmental effects of the wool-based monolith and crushed wool geopolymers were compared. Such research has not been conducted so far. For this purpose, water extracts from fragmented geopolymers were made, and tests were carried out following EN 12457-4. There is no information in the literature on the influence of geopolymer on the environment, which is an essential aspect of its possible use. The research results proved that the geopolymer made on the base of mineral wool meets the environmental requirements, except for the pH value. As mentioned in the article, the geopolymerisation process requires the dissolution of the starting material in a high pH (alkaline) solution. On the other hand, the pH minimum 11.2 value of fresh geopolymer binder is required to start geopolymerisation. Moreover, research results analysed in the literature showed that the optimum NaOH concentration is 8 M. for the highest compressive strength of geopolymer. Therefore, the geopolymer strength decreases with NaO concentration in the NaOH solution. Geopolymers glass wool-based mortars with Al₂O₃ obtained an average compressive strength of 59, the geopolymer with bauxite achieved about 51 MPa. Thus, Al₂O₃ is a better additional glass wool-based geopolymer than bauxite. The average compressive strength of rock wool-based geopolymer mortar was about 62 MPa. The average compressive strength of wool-based geopolymer binder was about 20–25 MPa. It was observed that samples of geopolymers grout without aggregate participation are characterised by cracking and deformation.     

Synthesis and Structural Characterization of CaO-P2O5-CaF:CuO Glasses with Antitumoral Effect on Skin Cancer Cells

Copper is one of the most used therapeutic metallic elements in biomedicine, ranging from antibacterial approaches to developing new complexes in cancer therapy. In the present investigation, we developed a novel xCuO∙(100 − x) [CaF₂∙3P₂O₅∙CaO] glass system with 0 ≤ x ≤ 16 mol% in order to determine the influence of doping on the composition structure of glasses. The samples were characterized by dissolution tests, pH measurements, Fourier-transform infrared spectroscopy (FT-IR), electron paramagnetic resonance (EPR), Scanning Electron Microscopy with energy dispersive spectroscopy (SEM-EDX) and afterward, their antitumor character was assessed. The glasses were mostly soluble in the aqueous medium, their dissolution rate being directly proportional to the increase in pH and the level of doping up to x = 8 mol%. FT-IR spectra of glass samples show the presence of all structural units characteristic to P₂O₅ in different rates and directly depending on the depolymerization process. SEM-EDX results revealed the presence of an amorphous glass structure composed of P, O, Ca, and Cu elements. The 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) reduction assay showed strong cytotoxicity for tumoral cells A375 even in low concentrations for Cu-treatment. In contrast, the copper-free matrix (without Cu) determined a proliferative effect of over 70% viability for all concentrations used.     

The Durability of Mortar Containing Alkali Activated Fly Ash-Based Lightweight Aggregate

Beneficiating fly ash as valuable construction material such as artificial lightweight aggregate (LWA) could be an alternative solution to increase the utilization of the industrial by-product. However, generally, LWA is characterized by high porosity and a related high water absorption, which on the one hand allows production of lightweight mortar, but on the other hand can affect its performance. Thus, in this research, the durability performance of mortar composed with alkali-activated fly ash-based LWA, and commercial expanded clay (EC) LWA was investigated. The fly ash LWA was prepared in a pan granulator, with a 6-molar solution of NaOH mixed with Na₂SiO₃ in a Na₂SiO₃/NaOH weight ratio of 1.5 being used as activator (FA 6M LWA). The results revealed that mortar containing FA 6M LWA had equivalent mechanical strength with mortar containing EC LWA. The mortar containing FA 6M LWA had comparable capillary water uptake and chloride migration resistance with the reference and EC LWA mortar. Furthermore, the addition of FA 6M LWA was proven to enhance the carbonation resistance in the resulting mortar, due to the denser interfacial transition zone (ITZ) of mortar with LWA.     

Influence of Bi2O3 on Mechanical Properties and Radiation-Shielding Performance of Lithium Zinc Bismuth Silicate Glass System Using Phys-X Software

We analyzed the mechanical properties and radiation-shielding performance of a lithium zinc bismuth silicate glass system. The composition of these glasses is 20ZnO-30Li₂O-(50-x)SiO₂-xBi₂O₃ (x varies between 10 and 40 mol%). The mechanical properties of the investigated glass system, such as Young’s modulus (E), bulk modulus (K), shear modulus (S), and longitudinal modulus (L), were determined using the Makishima–Mackenzie model. The elastic moduli gradually decreased with the addition of Bi₂O₃. E decreased from 46 to 31 GPa, K decreased from 27 to 14 GPa, S decreased from 19 to 14 GPa, and L decreased from 52 to 32 GPa as Bi₂O₃ was substituted for SiO₂. The mass attenuation coefficient (MAC) was investigated at energies between 0.284 and 1.33 MeV to understand the radiation-shielding performance of the glasses. The MAC value increased when SiO₂ was replaced by Bi₂O₃. We found that the effect of Bi₂O₃ on MAC values was noticeably stronger at energies of 0.284 and 0.347 MeV, while the effect of Bi₂O₃ on MAC values became weaker as energy increased. The linear attenuation coefficient (LAC) results demonstrated that if the samples were exposed to low-energy photons, the glass could prevent the penetration of photons, and thus, the glass samples were effective in radiation protection. The LAC values for the lowest- and highest-density samples changed from 0.998 to 1.976 cm⁻¹ (at 0.284 MeV) and from 0.286 to 0.424 cm⁻¹ (at 0.826 MeV). According to the radiation-shielding results, the thick, high-density glass sample has special and distinctive shielding properties.     

Effects of Vanadium on the Structural and Optical Properties of Borate Glasses Containing Er3+ and Silver Nanoparticles

The erbium-vanadium co-doped borate glasses, embedded with silver nanoparticles (Ag NPs), were prepared to improve their optical properties for potential optical fiber and glass laser application. The borate glasses with composition (59.5–x) B₂O₃–20Na₂O–20CaO–xV₂O₅–Er₂O₃–0.5AgCl (x = 0–2.5 mol%) were successfully prepared by conventional melt-quenching method. The structural properties of glass samples were investigated by XRD, TEM and by Fourier transform infrared (FTIR) spectroscopy while optical properties were carried out by UV–Vis spectroscopy by measuring optical absorption and the emission properties were investigated by photoluminescence spectroscopy. The XRD patterns confirmed the amorphous nature of the prepared glass samples whilst the FTIR confirmed the presence of VO₄, VO₅, BO₃ and BO₄ vibrations. UV–Vis–NIR absorption spectra reveal eight bands which were located at 450, 490, 519, 540, 660, 780, 980, and 1550 nm corresponding to transition of ⁴F_5/2, ⁴F_7/2, ²H_11/2, ⁴S_3/2, ⁴F_9/2, ⁴I_9/2, ⁴I_11/2, and ⁴I_13/2, respectively. The optical band gap (E_opt), Urbach energy and refractive index were observed to decrease, increase and increase, respectively, to the addition of vanadium. Under 800 nm excitation, three emission bands were observed at 516, 580 and 673 nm, which are represented by ²H_11/2–⁴I_15/2, ⁴S_3/2–⁴I_15/2 and ⁴F_15/2–⁴I_15/2, respectively. The excellent features of achieved results suggest that our findings may provide useful information toward the development of functional glasses.     

Effect of Solids-To-Liquids,Na2SiO3-To-NaOH and Curing Temperature on the Palm Oil Boiler Ash (Si + Ca) Geopolymerisation System

This paper investigates the effect of the solids-to-liquids (S/L) and Na₂SiO₃/NaOH ratios on the production of palm oil boiler ash (POBA) based geopolymer. Sodium silicate and sodium hydroxide (NaOH) solution were used as alkaline activator with a NaOH concentration of 14 M. The geopolymer samples were prepared with different S/L ratios (0.5, 1.0, 1.25, 1.5, and 1.75) and Na₂SiO₃/NaOH ratios (0.5, 1.0, 1.5, 2.0, 2.5, and 3.0). The main evaluation techniques in this study were compressive strength, X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), and Scanning Electron Microscope (SEM). The results showed that the maximum compressive strength (11.9 MPa) was obtained at a S/L ratio and Na₂SiO₃/NaOH ratio of 1.5 and 2.5 at seven days of testing.     

Physicochemical Properties and Fiber-Drawing Ability of Tellurite Glasses in the TeO2-ZnO-Y2O3 Ternary System

Glasses in the TeO₂-ZnO-Y₂O₃ (TZY) ternary system are examined in the present work. The vitrification domain of the chosen oxide matrix is determined and differential scanning calorimetry as well as X-ray diffraction measurements are carried out. The material characterizations reveal that Y₂O₃ incorporation cannot exceed 5 mol.% without causing detrimental crystallization within the glass. Optical transmission and refractive index investigations are conducted on compositions yielding fully amorphous samples. Next, the fiber drawing ability of selected yttrium-containing zinc-tellurite glasses is assessed and fiber-attenuation measurements in the mid-infrared are presented. Finally, a multimode step-index fiber is fabricated by combining a TZY cladding glass with a La₂O₃-based tellurite core glass. It is believed that yttrium-containing glasses could prove useful in association with other high glass transition temperature (>300 °C) TeO₂-based materials for the design of robust optical fibers with precisely engineered refractive index profiles.     

Trivalent Ions and Their Impacts on Effective Conductivity at 300 K and Radio-Protective Behaviors of Bismo-Borate Glasses: A Comparative Investigation for Al,Y, Nd,Sm, Eu

We aimed to determine the contribution of various trivalent ions like Al and rare-earths (Y, Nd, Sm, Eu) on resistance behaviors of different types of bismo-borate glasses. Accordingly, eight different bismuth borate glasses from the system: 40Bi₂O₃–59B₂O₃–1Tv₂O₃ (where Tv = Al, Y, Nd, Sm, and Eu) and three glasses of (40Bi₂O₃–60B₂O₃; 37.5Bi₂O₃–62.5B₂O₃; and 38Bi₂O₃–60B₂O₃–2Al₂O₃) compositions were extensively investigated in terms of their nuclear attenuation shielding properties, along with effective conductivity and buildup factors. The Py-MLBUF online platform was also utilized for determination of some essential parameters. Next, attenuation coefficients, along with half and tenth value layers, have been determined in the 0.015 MeV–15 MeV photon energy range. Moreover, effective atomic numbers and effective atomic weight, along with exposure and energy absorption buildup factors, were determined in the same energy range. The result showed that the type of trivalent ion has a direct effect on behaviors of bismo-borate glasses against ionizing gamma-rays. As incident photon energy increases, the effective thermal conductivity decreases rapidly, especially in the low energy range, where photoelectric effects dominate the photon–matter interaction. Sample 8 had the minimum heat conductivity at low photon energies; our findings showed that Eu-reinforced bismo-borate glass composition, namely 40Bi₂O₃–59B₂O₃–1Eu₂O₃, with a glass density of 6.328 g/cm³ had superior gamma-ray attenuation properties. These outcomes would be useful for the scientific community to observe the most suitable additive rareearth type and related glass composition for providing the aforementioned shielding properties, in terms of needs and utilization requirements.     

Self-Healing Products of Cement Pastes with Supplementary Cementitious Materials,Calcium Sulfoaluminate and Crystalline Admixtures

The phase composition of self-healing products generated in cracks affects self-healing performance. This study investigated the self-healing products of cementitious materials using supplementary cementitious materials (SCMs), a calcium sulfoaluminate (CSA) expansion agent, and crystalline additives (CAs). Ground-granulated blast-furnace slag (GGBFS), fly ash (FA), and silica fume (SF) were used as SCMs, and anhydrite, Na₂SO₄, Na₂CO₃, and MgCO₃ were used as crystalline additives (CAs). An artificial crack method was used to collect the self-healing products in the crack of the paste. The phase composition of the self-healing products was analyzed through X-ray diffraction (XRD)/Rietveld refinements and thermogravimetry/differential thermogravimetry (TG/DTG) analysis, and their morphology and ion concentration were examined through scanning electron microscopy with energy dispersive spectroscopy (SEM–EDS). From the results, the main compound of self-healing products was found to be calcite. GGBFS and FA decreased the content of portlandite, and the use of CAs led to the formation of alkali sulfate and alkali carbonate. The SEM–EDS analysis results showed that when GGBFS and FA were used, a large proportion of the self-healing products contained C-S-H and C-A-H, and the use of CSA led to the formation of monosulfate and ettringite.     

Elaboration and Characterization of Vitreous Fertilizers and Study of Their Impact on the Growth,Photosynthesis, and Yield of Wheat (Triticum durum L.)

Four different phosphate glass formulations (F₀, F₁, F₂, and F₃) were developed according o wheat nutrient requirements to be used as controlled-release fertilizers. These glasses contain macro-elements (P₂O₅-K₂O-CaO-MgO), with the addition of microelements (Fe-Mn-Zn-B-Cu-Mo) in each formulation. The effects of these elements’ addition on thermal properties, glass structure, and dissolution behaviors were investigated. Results showed that these glasses are composed essentially of metaphosphate chains and that the addition of micronutrients could change the chemical durability of phosphate glasses. A greenhouse experiment was performed using wheat (Triticum durum L.) to evaluate the efficiency of the four glasses, with or without application of chemical nitrogen (N) (N + VF and VF, respectively). The different formulas were tested using two rates of 0.3 and 1 g per plant. In addition to the vitreous fertilizer formulations, two other treatments were applied: control treatment with no amendment and Nitrogen-Phosphorus-Potassium treatment with the application of the conventional fertilizers on the base of optimal rates. After four months of cultivation, vitreous fertilizers application significantly improved growth (7% to 88%), photosynthetic (8% to 49%) parameters, and yield (29% to 33%) compared to NPK treatment and to the control. It has been found that formulas F₁, F₂, and F₃ may constitute a potential alternative to conventional fertilization due to their positive impact on wheat production and can be used in practice as an environmentally controlled-release fertilizer.     

Fabrication of Lead Free Borate Glasses Modified by Bismuth Oxide for Gamma Ray Protection Applications

In the present work, bismuth borate glass samples with the composition of (99-x) B₂O₃ + 1Cr₂O₃ + (x) Bi₂O₃ (x = 0, 5, 10, 15, 20, and 25 wt %) were prepared using the melt quenching technique. The mass attenuation coefficient (MAC) of the prepared glass samples was measured through a narrow beam technique using a NaI(Tl) scintillation detector. Four point sources were used (²⁴¹Am, ¹³³Ba, ¹⁵²Eu, and ¹³⁷Cs) to measure the MAC for the prepared glasses. The experimental data were compared with the theoretical results obtained from the XCOM, and it was shown that for all samples at all tested energies, the relative deviation between the samples is less than 3%. This finding signifies that the experimental data can adequately be used to evaluate the shielding ability of the glasses. The MAC of the sample with x = 25 wt % was compared with different lead borate glasses and the results indicated that the present sample has high attenuation which is very close to commercial lead borate glasses. We determined the transmission factor (TF), and found that it is small at low energies and increases as the energy increases. The addition of Bi₂O₃ leads to reduction in the TF values, which improves the shielding performance of the glass system. The half value layer (HVL) of the BCrBi-10 sample was 0.400 cm at 0.595 MeV, 1.619 cm at 0.2447 MeV, and 4.946 cm at 1.4080 MeV. Meanwhile, the HVL of the BCrBi-20 sample is equal to 0.171 and 4.334 cm at 0.0595 and 1.4080 MeV, respectively. The HVL data emphasize that higher energy photons tend to penetrate through the glasses with greater ease than lower energy photons. Furthermore, the fast neutron removable cross section (FNRC) was determined for the present samples and compared with lead borate glass and concrete, and the results showed a remarkable superiority of the bismuth borate glass samples.     

The Vital Role of La2O3 on the La2O3-CaO-B2O3-SiO2 Glass System for Shielding Some Common Gamma Ray Radioactive Sources

The role La₂O₃ on the radiation shielding properties of La₂O₃-CaO-B₂O₃-SiO₂ glass systems was investigated. The energies were selected between 0.284 and 1.275 MeV and Phy-X software was used for the calculations. BLa10 glass had the least linear attenuation coefficient (LAC) at all the tested energies, while BLa30 had the greatest, which indicated that increasing the content of La₂O₃ in the BLa-X glasses enhances the shielding performance of these glasses. The mass attenuation coefficient (MAC) of BLa15 decreases from 0.150 cm²/g to 0.054 cm²/g at energies of 0.284 MeV and 1.275 MeV, respectively, while the MAC of BLa25 decreases from 0.164 cm²/g to 0.053 cm²/g for the same energies, respectively. At all energies, the effective atomic number (Z_eff) values follow the trend BLa10 < BLa15 < BLa20 < BLa25 < BLa30. The half value thickness (HVL) of the BLa-X glass shields were also investigated. The minimum HVL values are found at 0.284 MeV. The HVL results demonstrated that BLa30 is the most space-efficient shield. The tenth value layer (TVL) results demonstrated that the glasses are more effective attenuators at lower energies, while decreasing in ability at greater energies. These mean free path results proved that increasing the density of the glasses, by increasing the amount of La₂O₃ content, lowers MFP, and increases attenuation, which means that BLa30, the glass with the greatest density, absorbs the most amount of radiation.     

Process Development of Fly Ash-Based Geopolymer Mortars in View of the Mechanical Characteristics

This study aimed to determine the effects of design parameters, including the liquid/solid ratio (L/S), Na₂SiO₃/NaOH weight ratio, and curing temperature, on class F fly ash-based geopolymer composites. For this purpose, two disparate sources of fly ash were supplied from Çatalağzı (FA) and İsken Sugözü (FB) Thermal Power Plants in Turkey. Two different L/S ratios of 0.2 and 0.4 were used. The Na₂SiO₃/NaOH ratios in the alkaline solutions were 1, 1.5, 2, 2.5, and 3 by weight for each type of geopolymer mixture. Then, 40 different mixes were cured at two specific temperatures (70 °C and 100 °C) for 24 h and then preserved at room temperature until testing. Thereafter, the physical water absorption properties, apparent porosity, and bulk density were examined at 28 days on the hardened mortars. Additionally, compressive and flexural tests were applied to the geopolymers at 7, 28, and 90 days. It was found that the highest compressive strength was 60.1 MPa for the geopolymer manufactured with an L/S of 0.2 and Na₂SiO₃/NaOH ratio of 2. Moreover, the best thermal curing temperature for obtaining optimal strength characteristics was 100 °C for the FB.     

Nonlinear Optical Limiting and Radiation Shielding Characteristics of Sm2O3 Doped Cadmium Sodium Lithium Borate Glasses

Strong nonlinear absorption (NLA), reduced optical limiting (OL) thresholds, and high radiation shielding parameters are required for the effective use of glasses in the laser radiation and nuclear radiation protecting materials. In view of this, the efficacy of Sm₂O₃ on the nonlinear optical (NLO) and OL properties were ascertained (at 532 nm) along with radiation shielding characteristics. The open and closed aperture Z-scan profiles revealed the presence of positive NLA and nonlinear refraction (NLR) phenomena respectively. OL measurements showed the existence of limiting behavior in the studied glasses. The NLA and NLR coefficients were improved while the OL thresholds were decreased as the doping of Sm₂O₃ elevated to a higher doping level. These improvements in NLA, NLR coefficients and OL efficiencies were attributed to the non-bridging oxygens and high polarizable Sm³⁺ ions. The NLA and OL results clearly suggest the high (5 mol %) Sm₂O₃ doped glass (Sm5CNLB) glass is beneficial to protect the delicate devices and human eye by suppressing the high energy laser light. The theoretical linear attenuation coefficients (LAC) values of the presented SmxCNLB glasses were obtained with the help of Phy-X software between 0.284 and 1.333 MeV. At 0.284 MeV, the maximum values occur and take values between 0.302 (for Sm0CNLB) and 0.409 cm⁻¹ (for Sm5CNLB). We found that the LAC for the presented SmxCNLB glasses is a function of Sm₂O₃ content, where the LAC tends to increase, corresponding to the high probabilities of interaction, as the content of Sm₂O₃ changes from 0 to 5 mol %. The effective atomic number (Z_eff) for the presented SmxCNLB glasses was examined between 0.284 and 1.333 MeV. As the amount of Sm₂O₃ is added, the Z_eff increases, and this was observed at any energy.