WNT10A variants: following the pattern of inheritance in tooth agenesis and self-reported family history of cancer

Clinical Oral Investigations - The aim of this study was the analysis of WNT10A variants in seven families of probands with various forms of tooth agenesis and self-reported family history of...     

From glass to life: a commentary on the assessment of the reproductive potential of cryopreserved human oocytes

Journal of Assisted Reproduction and Genetics -     

Plasmafiltration as an effective method in the removal of circulating pegylated liposomal doxorubicin (PLD) and the reduction of mucocutaneous toxicity during the treatment of advanced platinum-resistant ovarian cancer

Cancer Chemotherapy and Pharmacology - The present study evaluates the safety and efficacy of double-plasma filtration (PF) to remove the exceeding pegylated liposomal doxorubicin (PLD) in...     

Endogenous motion of liver correlates to the severity of portal hypertension

BACKGROUND Degree of portal hypertension(PH) is the most important prognostic factor for the decompensation of liver cirrhosis and death, therefore adequate care for patients with liver cirrhosis requires timely detection and evaluation of the presence of clinically significant PH(CSPH) and severe PH(SPH). As the most accurate method for the assessment of PH is an invasive direct measurement of hepatic venous pressure gradient(HVPG), the search for non-invasive methods to diagnose these conditions is actively ongoing.AIM To evaluate the feasibility of parameters of endogenously induced displacements and strain of liver to assess degree of PH.METHODS Of 36 patients with liver cirrhosis and measured HVPG were included in the casecontrol study. Endogenous motion of the liver was characterized by derived parameters of region average tissue displacement signal(dantero, dretro, d RMS) and results of endogenous tissue strain imaging using specific radiofrequency signal processing algorithm. Average endogenous strain μ and standard deviation σ of strain were assessed in the regions of interest(ROI)(1 cm × 1 cm and 2 cm × 2 cm in size) and different frequency subbands of endogenous motion(0-10 Hz and 10-20 Hz).RESULTS Four parameters showed statistically significant(P 0.05) correlation with HVPG measurement. The strongest correlation was obtained for the standard deviation of strain(estimated at 0-10 Hz and 2 cm × 2 cm ROI size). Three parameters showed statistically significant differences between patient groups with CSPH, but only dretro showed significant results in SPH analysis. According to ROC analysis area under the curve(AUC) of the σROI[0…10 Hz, 2 cm × 2 cm] parameter reached 0.71(P = 0.036) for the diagnosis of CSPH; with a cut-off value of 1.28 μm/cm providing 73% sensitivity and 70% specificity. AUC for the diagnosis of CSPH for μROI[0…10 Hz, 1 cm × 1 cm] was 0.78(P = 0.0024); with a cut-off value of 3.92 μm/cm providing 73% sensitivity and 80% specificity. Dretro parameter had an AUC of 0.86(P = 0.0001) for the diagnosis of CSPH and 0.84(P = 0.0001) for the diagnosis of SPH. A cut-off value of-132.34 μm yielded 100% sensitivity for both conditions, whereas specificity was 80% and 72% for CSPH and SPH respectively.CONCLUSION The parameters of endogenously induced displacements and strain of the liver correlated with HVPG and might be used for non-invasive diagnosis of PH.     

Heteroepitaxy of Cerium Oxide Thin Films on Cu(111)

An important part of fundamental research in catalysis is based on theoretical and modeling foundations which are closely connected with studies of single-crystalline catalyst surfaces. These so-called model catalysts are often prepared in the form of epitaxial thin films, and characterized using advanced material characterization techniques. This concept provides the fundamental understanding and the knowledge base needed to tailor the design of new heterogeneous catalysts with improved catalytic properties. The present contribution is devoted to development of a model catalyst system of CeO₂ (ceria) on the Cu(111) substrate. We propose ways to experimentally characterize and control important parameters of the model catalyst—the coverage of the ceria layer, the influence of the Cu substrate, and the density of surface defects on ceria, particularly the density of step edges and the density and the ordering of the oxygen vacancies. The large spectrum of controlled parameters makes ceria on Cu(111) an interesting alternative to a more common model system ceria on Ru(0001) that has served numerous catalysis studies, mainly as a support for metal clusters.