Standard versus customised locking plates for fixation of schatzker ii tibial plateau fractures

Aim3D-printed implants could improve the capture of fracture fragments for improved stability of tibial plateau fracture fixation. The aim of this study was to compare the biomechanical strength of fixation constructs using standard and customised 3D-printed proximal tibial locking plates for fixation of tibial plateau fractures.MethodsThis is a biomechanical study utilising six pairs of cadaveric tibiae. Fractures were created in an identical fashion using an osteotome and mallet, and fixed using either a standard, commercially-available proximal tibia locking plate or a customised 3D-printed plate. Design and production of the customised plates followed a “3D printing at point-of-care” model. Customised stainless steel 316 L plates were produced within a local additive manufacturing laboratory based upon pre-operative CT scans. Determination of implant choice within each cadaver pair was performed via simple randomisation. Following fracture fixation, the tibiae were skeletalised and biomechanically tested using a customised loading jig and a size-matched femoral knee prosthesis. The constructs were loaded cyclically from 100 N to approximately three times the cadaveric body-weight at 5 Hz for 10 000 cycles. Every 1000 cycles, the test was paused and the tibia was physically checked for failure. If failure had not occurred by the end of the testing cycle, the construct was loaded to failure and the load at which the construct failed was noted.ResultsFixation constructs using the 3D-printed plates performed comparably to those using the standard plates. There was no significant difference in the degree of fracture fragment displacement in both constructs. Overall longitudinal construct stiffness and load to failure was higher in the 3D-plates group but this did not reach statistical significance.ConclusionProduction of customised plates for proximal tibia fractures at point-of-care is feasible, however fixation constructs with these plates did not provide any biomechanical advantage over standard plates in terms of axial loading stiffness.     

基因间长链非编码RNA152靶向微小RNA?103a?3p对非小细胞肺癌细胞增殖和侵袭迁移的影响

目的探讨基因间长链非编码RNA 152(LINC00152)靶向调控微小RNA-103a-3p(miR-103a-3p)表达及对非小细胞肺癌(NSCLC)细胞增殖和侵袭迁移的影响。方法采用实时定量PCR(QPCR)检测正常肺上皮细胞BEAS-2B及NSCLC细胞(ANIP-973、NCI-H157、A549和NCI-H1975)的LINC00152水平。选取LINC00152水平最高的细胞分别转染LINC00152特异性小干扰RNA(si-LINC00152组)或无关序列(si-NC组),另设未转染细胞为对照组。QPCR检测LINC00152水平,活细胞计数CCK-8法、Transwell小室和划痕实验测定细胞增殖、侵袭和迁移能力,Western blotting检测基质金属蛋白酶(MMP)-2、MMP-9和第10号染色体缺失的磷酸酶及张力蛋白同源基因(PTEN)的水平;荧光素酶报告实验验证LINC00152靶向结合miR-103a-3p的能力。结果NSCLC细胞的LINC00152水平均高于BEAS-2B细胞(P<0.05),尤其是NCI-H1975细胞的最高。si-LINC00152组的LINC00152水平为0.352±0.087,低于对照组的1.058±0.219和si-NC组的1.126±0.139(P<0.05)。与si-NC组和对照组相比,si-LINC00152组NCI-H1975细胞转染48、72 h的增殖活力下降(P<0.05);si-LINC00152组的划痕愈合率和穿膜细胞数分别为(27.386±2.428)%和(78.840±5.031)个,低于si-NC组的(77.675±4.803)%和(179.208±13.264)个及对照组的(76.371±5.385)%和(174.003±15.678)个(P<0.05);与si-NC组和对照组相比,si-LINC00152组的MMP-2和MMP-9水平均降低,而PTEN水平升高(P<0.05)。对照组和si-NC组上述指标的差异无统计学意义(P>0.05)。双荧光素酶报告分析证实,miR-103a-3p模拟物降低了野生型LINC00152的荧光素酶活性(P<0.05),但对突变型无影响(P>0.05)。结论LINC00152在NSCLC细胞中高表达并发挥促癌作用,与NSCLC的迁移侵袭密切相关,LINC00152与miR-103a-3p间的相互作用在NSCLC靶向治疗中有一定潜能。     

(-)-Epigallocatechin-3-gallate,reduces corneal damage secondary from experimental grade II alkali burns in mice

Background

Since recent reports have shown that (-)-Epigallocatechin-3-gallate (EGCG) could be used for treating proliferative and inflammatory disorders, we explored its use for the management of corneal chemical burns.

Anisotropic Bladder Planning Target Volume in Bladder Radiation Therapy

Purpose

This study aimed to investigate 3 planning target volume (PTV) margin expansions and determine the most appropriate volume to be used in bladder preservation therapy when using daily cone beam computed tomography (CBCT). We aimed to establish whether a smaller PTV expansion is feasible without risking geographical miss.

3-磷酸甘油酸脱氢酶促进丝氨酸合成在肿瘤进展中的机制

丝氨酸生物合成途径活性的上调是许多癌症明显的共同特征。该途径的第一种限速酶3-磷酸甘油酸脱氢酶(PHGDH)在黑色素瘤、乳腺癌和肾癌等癌组织中高表达，对肿瘤细胞增殖、转移、侵袭有着重要作用。糖酵解中间产物3-磷酸甘油酸在PHGDH作用下，氧化为磷酸羟基丙酮酸并最终合成丝氨酸。丝氨酸转化为甘氨酸，然后在核苷酸、s-腺苷甲硫氨酸(SAM)和还原型谷胱甘肽(GSH)的合成中起着重要的作用。PHGDH 有望成为肿瘤治疗的新靶点。     

A biological or a synthetic mesh in immediate breast reconstruction? A cohort-study of long-term Health related Quality of Life (HrQoL)

ObjectivesMeshes/matrices are commonly used in immediate breast reconstruction. There are few studies comparing biological and synthetic meshes and it is unknown what type of mesh gives the best long-term results. The aim of this study was to compare long-term health-related quality of life (HrQoL) and patient satisfaction in implant-based immediate breast reconstruction with a biological mesh (Surgisis®) with that of patients reconstructed with a synthetic mesh (TIGR ® Matrix Surgical Mesh).Material and methodsBoth cohorts were prospectively included and consecutively operated. Clinical data was collected. HrQoL was evaluated with EuroQoL-5 dimension – 3 levels questionnaire (EQ-5D-3L) and the Hospital Anxiety and Depression Scale (HADS) and the Breast-Q.Results and conclusionSeventy-one patients were operated on in the biological group and 49 in the synthetic group. The response rates were 75 and 84 per cent, respectively. Mean follow-up time was 74 months and 23 months, respectively. There were no statistical differences in satisfaction and quality of life between the two groups. Complications and radiation seem to lead to a lower satisfaction. Our findings could indicate that biological and synthetic meshes give an equal long-term result as regards patients’ perceived quality of life.     

利用耳甲腔型小耳畸形残耳皮瓣及软骨改善再造耳颅耳沟效果观察

目的探讨对先天性耳甲腔型小耳畸形患者行全扩张法全耳再造术后，利用残耳皮瓣改善再造耳颅耳沟的效果。方法回顾分析 2012 年 1 月—2017 年 1 月收治的 150 例先天性耳甲腔型小耳畸形患者。其中男 92 例，女 58 例；年龄 6.5～35.0 岁，平均 11.1 岁。采用一期扩张器埋置、二期全扩张法全耳再造术后发现上部颅耳沟浅显；于 6～12 个月后行三期再造耳修整。将残耳垂通过“Z”字改型转移以再造耳垂。在残耳上部作蒂在轮屏切迹的残耳上部皮瓣，弧形切开松解并加深上部颅耳沟，将上部残耳皮瓣向颅耳沟创面旋转推进缝合以覆盖创面；将带皮下组织蒂的残耳软骨组织瓣插入支架底部形成的腔隙内，并缝合固定，以增加支架的高度；耳甲腔区其余残耳皮瓣用以覆盖耳甲腔创面。结果术后拆线时 1 例患儿皮瓣远端出现直径约 0.5 cm 的表皮水疱，经换药 2 周后愈合；其余患者皮瓣成活良好。患者均获随访，随访时间 6～12 个月，平均 9.6 个月。再造耳上部颅耳沟均明显加深，再造耳支架高度不同程度增加，双耳对称性佳，耳甲腔无明显挛缩变小，再造耳外观满意。再造耳上部表面毛发明显减少，耳周发际线上移。结论采用耳甲腔型小耳畸形的残耳皮瓣及残耳软骨瓣转移，不仅可加深颅耳沟，而且可增加上部支架的高度，术后颅耳沟变形较轻，再造耳与正常耳廓的对称性更佳。