医用钛合金在三种不同生理电解液中的耐腐蚀行为研究

利用电化学方法研究医用钛合金在0.9%NaCl生理盐水，模拟人工唾液，模拟人工体液中的腐蚀情况，分析腐蚀电位和腐蚀电流密度，扫面电镜观察腐蚀表面形貌，CA-A型接触角测试仪测试钛合金表面被腐蚀后接触角的变化。实验表明：钛合金在三种生理电解液中的腐蚀情况依次是：模拟人工唾液〉模拟人工体液〉0.9%NaCl生理盐水。扫面电镜观察表明，医用钛合金在0.9% NaCl生理盐水腐蚀后，表面出现了许多腐蚀孔，经模拟人体体液腐蚀后，表面变得粗糙不平整，腐蚀孔数目变化不大，钛合金经人工唾液腐蚀后，腐蚀孔数目增多，部分腐蚀孔孔径明显增大。经三种生理电解液腐蚀后，钛合金表面接触角都减小。结论：医用钛合金在人工唾液中的腐蚀最严重，在临床应用中应给予相应的防范措施。     

食管内支架置入术并发症分析及防治

目的：分析食管内钛镍记忆合金支架置入术并发症的可能原因及防治方法。方法：共52例病人，食管癌、贲门癌29例，食管胃吻合口狭窄21例，自发性食管破裂2例，共置入各种钛镍记忆合金支架54枚。随访观察3～36个月。结果：内支架置入全部成功，术后患吞咽困难症状均改善。术后出现的并发症包括支架移位3例，支架堵塞9例。吸入性肺炎3例，呕血7例，残余漏2例，疼痛和异物感24例，严重返流症状5例。经过相应的治疗，除2例大呕血患外，其余并发症均得到纠正。结论：虽然食管内钛镍记忆合金支架置入术后有不可忽视的并发症，但经过相应治疗，一般均可纠正，它是治疗食管恶性狭窄和自发性食管破裂有效的方法。     

668颗后牙镍铬合金PFM边缘适合性的临床观察

目的：观察采用2种边缘形式的后牙烤瓷熔附金属全冠边缘适合性和对牙龈健康的影响.方法：对668颗后牙,分别采用2种边缘形式的后牙烤瓷熔附金属全冠（单冠或桥的基牙）在修复2年后进行复查,检测其边缘适合性及牙龈指数（GI）和牙周探诊深度（PD）,用统计学方法分析修复体边缘形式与牙龈病变间的关系.结果：采用羽状边缘360°金属脚边的PFM边缘适合性明显优于凹面肩台型边缘PFM,凹面肩台型边缘的PFM的牙龈病变发生率,明显高于羽状边缘360°金属脚边的PFM,而边缘适合性差者较适合性好者牙龈病变发生率显著增高.结论：后牙PFM的边缘采用羽状边缘360°金属脚边是一种好的选择.     

Patch testing with beryllium alloy samples in guinea pigs

An experimental study was conducted in guinea pigs for the predictive assessment of the beryllium alloy hazard in occupational exposure of the skin to beryllium compounds. Guinea pigs were sensitized to beryllium sulfate according to the maximized Magnusson and Kligman test, and challenged with beryllium alloys and metallic copper, beryllium and aluminum samples. Results showed a delayed skin hypersensitivity reaction in 30 to 60% of pre-sensitized guinea pigs challenged with copper-beryllium alloys and aluminum-beryllium alloy. An inflammatory follicular reaction was induced by copper in both controls and pre-sensitized guinea pigs.     

Ordering behaviors and age-hardening in experimental AuCu-Zn pseudobinary alloys for dental applications

Age-hardening mechanisms and related ordering behaviors of the experimental (AuCu)_1−xZn_x alloys with x0.2 were investigated for dental applications. The addition of Zn to equiatomic AuCu greatly increased the age-hardening rate and delayed overaging. It was suggested that the quenched-in excess vacancies were greatly related to the age-hardening rate in the AuCu–Zn pseudobinary alloys. In these alloys, the hardness became maximum during the very initial stage of ordering, and with the development of ordered phase, the hardness began to decrease. Transmission electron microscopy revealed that the age-hardening of AuCu–Zn pseudobinary alloys is caused by lattice distortion that occurred during the very early stage of atomic ordering. The addition of Zn to AuCu effectively increased the density of antiphase boundaries per unit volume of the AuCu II superstructure. This is suggested to be the main cause for the retardation of the overaging in the alloys containing Zn of 5 at% or more. This pronounced effect of Zn addition to AuCu alloy on its age-hardening characteristics may be advantageous for obtaining stable mechanical properties of dental casting gold alloys.     

材料参数与镍钛形状记忆合金的本构关系

在Ｔａｎａｋａ模型基础上，我们讨论了形状记忆合金热力学特性的本构关系。特别注意了桓温拉伸过程和强迫回复过程。本构方程的材料参数，即弹性模量Ｄ，变化张量Ω，热力弹性张量均以镍钛合金实验测试值来确定。在不同的应力－应变－温度关系试验中发现Ｄ和Ω与温度之间有很强的相关性。     

An analytical method for quantitative estimation of the cytotoxicity of dental alloys

INTRODUCTION　　The two mostimportantcriteria fordental materialsare their bio-functionalandbio-compatible endurance within the anticipated life-span of the dental restoration inthe mouth.The bio-compatibility of amaterial relates mainly to theallergenici…     

Property Criteria for Automotive Al-Mg-Si Sheet Alloys

In this study, property criteria for automotive Al-Mg-Si sheet alloys are outlined and investigated in the context of commercial alloys AA6016, AA6005A, AA6063 and AA6013. The parameters crucial to predicting forming behavior were determined by tensile tests, bending tests, cross-die tests, hole-expansion tests and forming limit curve analysis in the pre-aged temper after various storage periods following sheet production. Roping tests were performed to evaluate surface quality, for the deployment of these alloys as an outer panel material. Strength in service was also tested after a simulated paint bake cycle of 20 min at 185 °C, and the corrosion behavior was analyzed. The study showed that forming behavior is strongly dependent on the type of alloy and that it is influenced by the storage period after sheet production. Alloy AA6016 achieves the highest surface quality, and pre-ageing of alloy AA6013 facilitates superior strength in service. Corrosion behavior is good in AA6005A, AA6063 and AA6016, and only AA6013 shows a strong susceptibility to intergranular corrosion. The results are discussed below with respect to the chemical composition, microstructure and texture of the Al-Mg-Si alloys studied, and decision-making criteria for appropriate automotive sheet alloys for specific applications are presented.