Endocrown restorations: Influence of dental remnant and restorative material on stress distribution

Objective

The goal of this study was to evaluate the stress distribution in a tooth/restoration system according to the factors “amount of dental remnant” (3 levels) and “restorative material” (2 levels).

下颌第二磨牙咬合接触变化对颞下颌关节应力分布的影响

目的 用力学研究方法结合有限元技术分析下颌第二磨牙咬合接触部位改变时，相同压强咬合载荷条件下颞下颌关节应力的变化。方法 在包括左侧下颌第二磨牙在内的颞下颌关节三维有限元模型上，设计下颌第二磨牙牙尖交错He(ICO)、远中和颊侧3种加载部位的工况，通过有限元运算探讨双侧髁突应力分布的变化规律。结果 由于咬合加载部位的牙面承载形态不同，在双侧髁突上产生了不同的应力效应，其变化包括应力性质和应力分布特点等方面，远中加载和颊侧加载时对侧髁突的Von Mises应力最大值由ICO加载时的51．51MPa分别增加到72．15MPa和69．57MPa。结论 与单侧下颌第二磨牙承载部位变化相关的咬合力方向变化，可使同一力值的咬合力产生不同的双侧髁突应力效应。     

下颌第一磨牙种植固定桥的受载分析

目的 观察下颌第一磨牙种植固定桥的位移和应力分布规律。方法 采用了三维有限元法进行受载分析。结果 发现第二双尖牙的最大位移值较大;由于固定桥的支架作用,垂直分散载荷下天然基牙和种植基牙的位移均值之间差异无显著性。基牙颈部为应力集中区,第二双尖牙根尖的应力较小。集中载荷加于基牙时,位移和应力值明显增加。结论 提示应注意末端种植基牙的载荷和咬合状态,该设计是临床可使用的特殊固定桥。     

A comparison of 2D and 3D finite element analysis of a restored tooth

The finite element method is widely used in dental research. The decision to use two-dimensional (2D) or three-dimensional (3D) modelling is dependent on many interrelated factors. The purpose of the present study was to compare and contrast 2D and 3D finite element analysis (FEA) in investigating the mechanical behaviour of a maxillary premolar restored with a full crown under similar conditions of axial and lateral occlusal loading. The 2D analysis required modelling both a buccolingual and mesiodistal section of the restored premolar and for comparison sections of a 3D model were examined. Differences in the results for displacement and maximum principal stress distribution within the component structures and interfaces of the 2D and 3D models were, in general, attributable to differences in geometry represented in the models. Maximum principal stresses tended to be greater under lateral rather than axial occlusal loading. It was concluded that 2D FEA may find application in investigating key aspects of the mechanical behaviour of a dental restoration in a single tooth unit, but that in certain situations combinations of 2D and 3D FEA may offer the best understanding of the biomechanical behaviour of complex dental structures. Sophisticated FE models are required to better understand the mechanical behaviour of restored tooth units.     

Influence of the shape of the layers in photo-cured dental restorations on the shrinkage stress peaks—FEM study

ObjectiveThe aim of the paper is to analyse an influence of the shape of the layers in photo-cured dental restorations of Class I on distribution of shrinkage stresses along the tooth-restoration interface. The study is a continuation of the previous considerations (Kowalczyk and Gambin (2008) [1]), where techniques, which reduce stress concentration at the top of the tooth-restoration interface, were considered. The analysis leads to proposition of new layer forming techniques, which diminish the stress peaks at the interface and prevent the crack propagation process.MethodsTo find the stress distributions in the dental restoration layers and the tooth tissues the finite element method implemented in the ABAQUS (Simulia, Providence, USA) software is used. For Class I restoration of the premolar tooth, the axisymmetrical model is assumed. The restoration is made of four layers of a photo-cured composite. Between the tooth tissues and the restoration, a layer of bonding agent 0.01 mm thick is placed and modeled by FEM with help of the cohesive elements. The assumed model takes into account an influence of changes of elastic properties and viscous effects. For each case of the restoration layers system, the Huber–Mises stresses are analysed.ResultsThe investigations show that the stresses near the restoration-tooth tissue interface are reduced due to viscous flow of the cured material and due to existence of a thin layer of the bonding agent. However, the stress distribution both, in the restoration and in the tooth tissues, is strongly dependent on a shape of the filling layers. Numerical simulations disclose that stress peaks are located at the top corners of each layer. The top corners of the last layer are the places where microleakage may occur. Stress concentrations at the corners of the preceding layers may lead to a growth of uprising crack. It will be shown that the flat layers in the restoration create relatively high values of the stress peaks. The rounded layers, with shapes close to those used in dental practice, reduce maximal stresses about 40%. According to a common opinion of dentists, the wedge-shaped layers give the best result. In the present paper, another way of the shrinkage stress reduction is proposed. Before the layering, one can cover the surface of the tooth cavity with a thin “pre-layer”. Next, the remainder cavity may be filled with flat, rounded or wedged layers. It will be shown, that in the fillings with the pre-layers, stress peaks are reduced up to 75%, with respect to the fillings composed of the rounded layers only. The proposed method considerably reduces the shrinkage stress, both in the tooth restoration, as well as, in the tooth tissues.SignificanceThe fillings with the pre-layer are easy in application and its analysis gives promising results. The pre-layer may be applied with other layers of different shapes, and its thickness may vary. The method is recommended for cavities with a great loss of the tooth tissue.     

气孔缺陷对磨牙双层全瓷冠力学性能影响的有限元研究

目的研究饰瓷气孔缺陷对磨牙二硅酸锂（LDG）及氧化锆（Y-TZP）双层全瓷冠力学性能的影响。 方法制作上颌第一磨牙LDG双层全瓷冠,使用显微CT扫描并三维重建分析饰瓷内气孔缺陷的尺寸及分布。分别构建上颌第一磨牙LDG及Y-TZP双层全瓷冠三维有限元模型,根据CT数据于饰瓷内添加气孔缺陷并进行加载;A组为对颌牙以200 N加载于牙冠模拟牙尖交错位时的垂直向受力;B组为以200 N与牙长轴呈45°加载于牙冠近、远中舌尖颊斜面,模拟侧方受力;C组为压头垂直位移1 mm加载于牙冠中央窝,模拟体外实验中的加载;计算最大主应力并分析气孔缺陷对其数值的影响。 结果LDG与Y-TZP在各载荷条件下的应力分布近似;垂直向加载时牙尖接触区应力集中,最大应力分别为51.683、50.084 MPa,存在气孔时,应力集中于牙尖接触应力区的气孔缺陷,最大应力上升至290.72、285.92 MPa;45°斜向加载时拉应力集中于核瓷颈部,气孔缺陷无应力集中,最大应力不变;体外加载时中央窝、沟及加载点应力集中,最大应力为107.3、125.41 MPa,存在气孔时,应力集中于拉应力区的气孔缺陷,最大应力上升至359.93、322.39 MPa。 结论饰瓷气孔缺陷对双层全瓷冠应力分布的影响与受载方式有关,位于拉应力集中区的气孔缺陷是导致冠失效的因素。     

Influence of gender and social factors on oral health,treatment degree and choice of dental restorative materials in patients from a dental school

To cite this article:
Int J Dent Hygiene
DOI: 10.1111/j.1601‐5037.2009.00401.x
Willershausen B, Witzel S, Schuster S, Kasaj A. Influence of gender and social factors on oral health, treatment degree and choice of dental restorative materials in patients from a dental school. Abstract: Objective: The attitude towards oral health is influenced by gender, the level of education and the social background of the patients The aim of the present study was to determine a possible relationship of gender, the educational level and the oral health as well as the choice of dental restorations. Methodology: A total of 2374 outpatients (age: 18–80 years) from a University dental school were assessed. Inclusion criteria were 15 remaining teeth and good general health. In addition to anamnesis data, information concerning educational level and present occupation was collected. The dental assessment included number of teeth, endodontic treatment, type of restorations (root canal fillings, restoration materials) as well as dental panoramic radiographs (OPG). Results: The female patients demonstrated a statistically significant higher percentage of restoration, more teeth with crowns and more tooth coloured fillings compared to men (P < 0.01). Patients with a higher level of education preferred more expensive restorations, whereas patients with a low level of education exhibited more inexpensive restorations. However, patients with private health insurance showed lower levels of carious lesions. Conclusion: The examined patients showed no significant correlation between educational level and type of dental restorations but female patients had a lower number of teeth and more restoration.     

七种不同（牙合）型对颞下颌关节应力影响的三维有限元分析

目的　探讨由形态变化产生的根尖主应力变化对颞下颌关节 (TMJ)应力的影响。方法　取光弹法测得的正中载荷作用下 7种型各牙根尖应力参数 ,在所建下颌骨三维有限元模型上加载 ,比较其TMJ应力。结果　 (1)髁突前斜面及其表面软骨和关节盘中部主要承受压应力 ,髁突后斜面及其表面软骨和关节盘后部主要承受拉应力 ;(2 )与正常相比 ,平面、远中、部分后牙反、缺牙的TMJ应力均有不同程度变化 ,其中平面的变化最明显。单侧上颌第三磨牙伸长、单侧下颌第三磨牙伸长的TMJ应力变化均不明显。结论　由型改变导致的正中咬合时根尖主应力变化 ,对关节应力性质的影响不明显 ,但对应力大小有一定影响。     

下颌骨各向异性材质模型对种植牙有限元分析的影响

目的 建立含螺纹种植体各向异性的完整下颌骨有限元模型,研究各向异性材质模型模拟对牙种植体有限元分析的影响.方法 采用薄层CT扫描和自主开发的软件分别建立各向异性和等效各向同性的完整下颌骨三维有限元模型,其中在后牙区植入两枚牙种植体,分析在颊舌向、斜向加载时,种植体-骨界面主应力和主应变值的变化.结果 在各向异性下颌骨模型中,除骨皮质第一最小主应力减小6.3%～7.6%和骨松质第三最小主应力减小8.7%～46.0%外,骨界面绝大多数主应力和所有主应变值均大于各向同性;骨皮质主应力增加2.1%～74.1%,主应变增加4.7%～57.3%;骨松质主应力增加10.3%～71.4%,主应变值增加19.5%～63.4%,而且骨松质应力的增加比骨皮质明显.结论 下颌骨种植牙有限元分析时,下颌骨各向异性模拟会明显影响骨界面应力和应变值,并以增加为主.在生物力学研究中应更注重下颌骨各向异性的材质力学特性.     

根管锥度和根管固位材料对牙体组织应力分布影响的三维有限元分析

目的 观察3种锥度根管采用不同根管桩修复对牙体组织应力分布的影响,以期为临床合理选用根管桩提供实验依据.方法 分别建立35号K锉、ProTaper和Profile器械根管预备后的下颌第一磨牙三维有限元模型,并分别模拟纤维树脂桩、不锈钢根管桩和银汞合金桩根管固位修复.运用Marc有限元软件,采用中央垂直加载,分析3种不同根管桩修复时牙颈部和牙根部应力分布的状况.结果 不同根管锥度对3种根管固位方式下的应力分布趋势无明显影响.不锈钢根管桩应力集中部位主要位于远中牙根中上部,远中根管口最高Von-Mises应力约为45 Mpa;银汞桩应力集中部分主要位于远中根管口上端及髓腔内,远中根管口最高Von-Mises应力约为16 Mpa;纤维树脂桩应力分布较均匀,未见明显应力集中.结论 纤维桩是比较理想的根管固位形式,应力分布接近于无根管桩状态;不锈钢根管桩在根中部容易形成高应力集中,增加根折发生率.

Abstract：

Objective To evaluate the effect of root canal taper and post on tooth stress distribution. Methods Three-dimensional finite element models of human mandibular first molar with root canals prepared with 35# K file, ProTaper and Profile were established. The tooth were restored with fiberresin, stainless steel and silver amalgam posts respectively. A vertical load on tooth occlusal surface was simulated. Marc software was used to analyze and calculate the stress distributions in the tooth restored with three kinds of different root canal posts, especially the in the cervical part and root. Results Different tapered root canals had no obvious influence on stress distribution in all three different posts. Stress distribution of stainless steel post located at the cervical and middle part of distal root, the highest Von-Mises stress was about 45 MPa. Stress distribution of silver amalgam post located at the orifice of root canal and pulp fundus, the highest Von-Mises stress was about 16 MPa. Stress distribution of fiber-resin post had no obvious stress concentration. Conclusions Fiber-resin post is the most ideal root canal post. Stainless steel post causes remarkable stress concentration in the root, which may raise the possibility of root fracture.     

全瓷冠内部应力分布规律的三维有限元研究

目的 运用有限元法分析全瓷冠的应力分布规律,为临床修复没计提供依据.方法 利用CT断层影像构建右下第一磨牙全瓷冠三维有限元模型.设计5种加载方式:垂直集中载荷600 N、垂直八点分布载荷600 N、垂直偏舌侧载荷600 N、10°偏颊侧载荷600 N、颊侧20°咀嚼载荷225 N,利用ANSYS软件分析各瓷层和界面的应力值大小.结果 5种加载方式下全瓷冠应力分布的相同之处:加载点可引起饰面瓷应力集中,沿载荷方向核瓷内表面拉应力集中.5种加载方式下全瓷冠应力分布的不相同之处:垂直集中载荷作用下,全瓷冠颈部肩台拉应力分布均匀;10°偏颊侧载荷仅使全瓷冠颊舌侧颈部肩台拉应力集中,最大值为32.25 MPa;颊侧20°咀嚼载荷引起全瓷冠颊侧、近中、远中颈部肩台拉应力集中,最大值为11.29 MPa.结论 制作全瓷冠应增加咬合接触面积,减少牙尖斜度,并提高颈部肩台陶瓷的抗拉能力.     

双皮层骨种植影响牙种植体稳定性的有限元固有频率分析

目的:用有限元方法研究双皮层骨种植对牙种植体初期稳定性的影响。方法:建立牙种植体、局部下颌骨块三维有限元模型,利用ABAQUS有限元软件,分析双皮层骨种植对种植体颊舌向、轴向一阶振动固有频率的影响。结果:在模拟的3种不同骨质类型中,双皮层骨种植均可提高种植体颊舌向、轴向振动的固有频率值,但颊舌向频率的增加有限,最高增加了13. 77%,而轴向频率值最大增加了一倍以上。结论:双皮层骨种植主要增加种植体轴向稳定性,对种植体水平向稳定性的增加有限。     

根管治疗后上颌前磨牙直接粘接修复的应力分布

目的 通过有限元法分析根管治疗后牙齿直接粘接修复的应力分布,为临床选择修复方法提供理论依据.方法 利用微型CT扫描信息,建立因正畸治疗拔除的年轻男性上颌第二前磨牙三维有限元模型,模拟根管治疗后远中验面缺损的4种不同直接粘接修复方法(G3:单纯粘接修复;G4:腭尖覆盖修复;G5:全验面覆盖修复;G6:远中验面覆盖),以完整牙(G1)和缺损未修复牙(G2)作为对照.在两牙尖斜面上加载200 N的轴向载荷,分析各组修复后牙齿的应力分布情况及安全因子的大小.结果 G1 ～ G6组总体拉应力峰值依次为106、383、287、56、62和95 MPa;G3 ～ G6组修复体安全因子依次为5.46、1.38、1.43及1.73,粘接层安全因子依次为0.33、0.52、5.16及2.11.结论 综合牙齿应力分布和安全因子因素,全(牙合)面或保留一侧完整边缘嵴的(牙合)面覆盖修复方式优于单纯粘接修复和腭尖覆盖的修复方式.     

Influence of ibuprofen combined with corticotomy on tooth movement and alveolar bone remodeling in rats

ObjectivesTo investigate the effects of corticotomy-assisted orthodontic tooth movement and administration of ibuprofen on tooth movement rate and alveolar bone response.Materials and MethodsA total of 78 adult male Wistar rats were randomly assigned to five groups: one baseline group (no treatment) and four experimental groups including orthodontic tooth movement only (OTM), orthodontic tooth movement with ibuprofen (OTMI), corticotomy-assisted orthodontic tooth movement (COTM), and corticotomy-assisted orthodontic tooth movement with ibuprofen (COTMI). Corticotomy was performed on a maxillary molar unilaterally. Nickel-titanium closed-coil springs generated a 10-gram force for maxillary first molar movement. The experimental drug groups received 15 mg/kg of ibuprofen, and the other groups received reverse osmosis water. Tooth movement and bone volume fraction were evaluated by micro–computed tomography on days 0, 7, 14, and 21.ResultsThe corticotomy groups had statistically significantly higher tooth movement and lower bone volume fraction than the orthodontic groups (P < .05). The amount and rate of tooth movement were statistically significantly different between the OTM and OTMI groups, but not statistically significantly different in bone volume fraction. However, statistically significant differences were not observed in any measurements between the COTM and COTMI groups.ConclusionsIbuprofen during orthodontic tooth movement inhibited tooth movement and alveolar bone remodeling but had no effect on corticotomy-assisted orthodontic treatment.     

下颌后牙区不同骨质内种植体即刻负载的三维有限元分析

目的 采用三维有限元分析探讨种植体在下颌后牙区不同骨质条件下即刻负载的应力分布,以期为即刻负载的应用选择提供参考.方法 建立下颌后牙区654-|种植体及上部牙冠和牙槽骨的即刻负载模型,根据骨皮质和骨松质比例构成不同分为B1(颌骨完全由均质的骨皮质构成)、B2(3 mm厚骨皮质包绕致密骨松质)、B3(1.5 mm厚骨皮质包绕致密骨松质)、B4(1.5 mm厚骨皮质包绕疏松骨松质)4种骨质条件,模拟颊舌向45°、100 N的力在修复体中心集中加载,分析各种植体在不同骨质内的von Mises应力分布.结果 颊舌向加载后von Mises应力主要集中于种植体颈部舌侧骨皮质,由B1至B4种植体4-|颈周骨内应力平均值[分别为(13.17±9.32)、(12.95±9.14)、(15.00±9.44)、(16.81±10.74)N]和种植体5-|颈周骨内应力平均值[分别为(15.51±10.32)、(14.73±8.96)、(16.79±8.40)、(18.34±8.45)N]的改变趋势一致,B3应力明显高于B1、B2,B4应力明显高于B3(P＜0.05).从B1～B4种植体6-|颈周骨内应力平均值[分别为(42.45±25.71)、(41.66±25.29)、(42.70±23.24)、(42.06±23.66)N]随骨质改变不大,但均显著高于相应骨质内4-|、5-|颈周骨内应力(P＜0.05).结论 在本项实验条件下进行即刻负载,种植体周围应力分布不仅受颌骨骨质的影响,种植体的植入位置以及建立合理的咬合同样非常重要.

Abstract：

Objective To assess and compare the peri-implant stress distribution of three posterior implants under immediate loading with 4 different bone qualities using three dimensional (3D) finite element (FE) analysis. Methods A 3D finite element model representing three implants in a portion of mandible at the 654-| region was developed, and three implants received a crown each. Four types of bone qualities (B1,B2, B3 and B4) were designed for the model. Load of 100 N was applied on the occlusal surfaces of the crowns at a 45° angle to the vertical axis of the implants. Results Von Mises stresses in the peri-implant bone of4-| in bone quality from B1 to B4 were ( 13. 17 ± 9. 32), ( 12. 95 ± 9. 14), ( 15. 00 ± 9. 44 ), and(16.81 ±10.74) MPa, and those of 5-| were (15.51 ± 10.32), (14.73 ±8.96), (16.79 ±8.40), and(18. 34 ±8.45) MPa. Stress in bone quality B4 showed the highest value, followed by B3 bone, the loweststress were found in B1 and B2 bone. It was significantly different (P ＜0. 05). However, von Mises stresses in different quality of bone around 6-| [(42.45 ±25.71), (41.66 ±25.29), (42.70 ±23.24), (42.06 ±23.66) MPa] were close to each other, and were as twice or three times as those of 4-| and 5-| , irrespective of different bone qualities. Conclusions The stress distribution around implant under immediate loading was not only affected by different bone qualities, but also by the direction of loading, and the latter may have a greater impact when a severe load delivered.     

Influence of microcapsule parameters and initiator concentration on the self-healing capacity of resin-based dental composites

ObjectiveFracture is one of the main causes for failure of resin-based composite restorations. To overcome this drawback, self-healing resin-based composites have been designed by incorporation of microcapsules. However, the relationship between their self-healing capacity and microcapsule and resin parameters is still poorly understood. Therefore, the objective of this study was to systematically investigate the effect of initiator concentration (in the resin) and microcapsule size and concentration on the self-healing performance of commercially available flowable resin-based composites.MethodsPoly(urea-formaldehyde) (PUF) microcapsules containing acrylic healing liquid were synthesized in small (33 ± 8 μm), medium (68 ± 21 μm) and large sizes (198 ± 43 μm) and characterized. Subsequently, these microcapsules were incorporated into a conventional flowable resin-based composite (Majesty Flow ES2, Kuraray) at different contents (5–15 wt%) and benzoyl peroxide (BPO) initiator concentrations (0.5–2.0 wt%). Fracture toughness (K_IC) of test specimens was tested using a single edge V-notched beam method. Immediately after complete fracture (K_IC-initial), the two fractured parts were held together for 72 h to allow for healing. Subsequently, fracture toughness of the healed resin-based composites (K_IC-healed) was tested as well.ResultsThe fracture toughness of healed dental composites significantly increased with increasing microcapsule size and concentration (2 wt% BPO, p < 0.05). The highest self-healing efficiencies (up to 76%) were obtained with microcapsules sized 198 ± 43 um.Significancecommercially available resin-based composites can be rendered self-healing most efficiently by incorporation of large microcapsules (198 ± 43 μm). However, long-term tests on fatigue and wear behavior are needed to confirm the clinical efficacy.     

Evaluation of early resin luting cement damage induced by voids around a circular fiber post in a root canal treated premolar by integrating micro-CT,finite element analysis and fatigue testing

Objective

This study utilizes micro-CT image combined with finite element (FE) analysis and in vitro fatigue testing to investigate the mechanical behavior associating with early resin luting cement damage induced by voids around a circular fiber post in a root canal treated premolar.

Influence of artificial saliva on abrasive wear and microhardness of dental composites filled with nanoparticles

OBJECTIVES: The aim of this study is to compare the wear resistance and hardness of two dental nanohybrid composites and to evaluate the influence of artificial saliva storage on those properties. METHODS: Specimens were made from two commercial nanohybrid dental composites (Esthet-X((R))-Dentsply and Filtek Supreme((R))-3M). Abrasion tests were carried out in a ball-cratering machine (three body abrasion) and microscopic analysis of the wear surfaces was made using optical and scanning electron microscopy; hardness was quantified by Vickers hardness test. Those tests were repeated on specimens stored in artificial saliva. RESULTS: Results show that the wear rate of the studied materials is within 10(-7)mm(3)/Nmm range, one of the composites presenting wear rate twice as large as the other. After storage in artificial saliva, the wear resistance increases for both materials. Microhardness of the composites is around 52 and 64HV, Esthet-X((R)) presents higher hardness values than Filtek Supreme((R)). After storage in artificial saliva, the microhardness of both materials decreases. Data were analyzed using ANOVA test, p相似文献   

The influence of various core designs on stress distribution in the veneered zirconia crown: a finite element analysis study

PURPOSE

The purpose of this study was to evaluate various core designs on stress distribution within zirconia crowns.

MATERIALS AND METHODS

Three-dimensional finite element models, representing mandibular molars, comprising a prepared tooth, cement layer, zirconia core, and veneer porcelain were designed by computer software. The shoulder (1 mm in width) variations in core were incremental increases of 1 mm, 2 mm and 3 mm in proximal and lingual height, and buccal height respectively. To simulate masticatory force, loads of 280 N were applied from three directions (vertical, at a 45° angle, and horizontal). To simulate maximum bite force, a load of 700 N was applied vertically to the crowns. Maximum principal stress (MPS) was determined for each model, loading condition, and position.

RESULTS

In the maximum bite force simulation test, the MPSs on all crowns observed around the shoulder region and loading points. The compressive stresses were located in the shoulder region of the veneer-zirconia interface and at the occlusal region. In the test simulating masticatory force, the MPS was concentrated around the loading points, and the compressive stresses were located at the 3 mm height lingual shoulder region, when the load was applied horizontally. MPS increased in the shoulder region as the shoulder height increased.

CONCLUSION

This study suggested that reinforced shoulder play an essential role in the success of the zirconia restoration, and veneer fracture due to occlusal loading can be prevented by proper core design, such as shoulder.     

下颌磨牙残冠纤维桩核冠修复的有限元应力分析

目的 分析下颌第一磨牙残冠不同缺损壁数的情况下,不同数目、不同部位的纤维桩核冠修复的应力分布情况和应力大小.方法 利用三维有限元法建立下颌第一磨牙残冠2壁和3壁缺损情况下,不同数目和不同部位的纤维桩核冠修复模型,施加225N垂直向的静态载荷及动态载荷.记录两种载荷下各部位牙本质von Mises应力最大值和最大主应力.结果 下颌磨牙2种缺损状态在动静态载荷下,未植入纤维桩组最大Von Mises应力最大,均高于植入纤维桩组,近中植入2根纤维桩组和植入3根纤维桩组的应力分布最均匀.下颌磨牙3壁缺损在静态载荷下,植入3根纤维桩组最大,Von Mises应力明显小于其他2组.结论 2壁缺损情况下,考虑选择植入1根纤维桩.3壁缺损情况下,可以考虑通过增加纤维桩数量来分散应力,减小牙体折裂风险.