香叶木素固体脂质纳米粒的制备及质量评价

目的 制备香叶木素固体脂质纳米粒并对其进行质量评价。方法 采用溶剂注入法制备香叶木素固体脂质纳米粒,用 Box-Benhnken效应面法优化处方,并通过包封率、微观形态、粒径分布和Zeta电位对香叶木素固体脂质纳米粒的质量进行评价。 结果 香叶木素固体脂质纳米粒最优处方组成：表面活性剂浓度3.39%,棕榈酸浓度0.116%,脂药质比为21:100,制备的香叶木素 固体脂质纳米粒外观澄清透明,带淡蓝色乳光;平均粒径为(91.73±3.18)nm(n=3),PDI为0.228,电位为(-11.46±0.74)mV(n=3);包 封率为95.13%,载药量为9.04%;透射电镜照片显示纳米粒大小均一,呈球形或类球形。 结论 该处方可用于香叶木素固体脂 质纳米粒的制备,工艺简单,稳定可行。     

薄膜-超声法制备芦丁固体脂质纳米粒的研究

目的优化薄膜-超声法制备芦丁固体脂质纳米粒的处方。方法以包封率为指标,采用正交设计优化法考察硬脂酸和大豆卵磷脂的用量、吐温-80和聚乙二醇-400的体积分数对包封率的影响,优选最佳处方。用透射电镜观察外观形态,用电位/纳米粒度分析仪分析纳米粒的粒径及Zeta电位,用透析法评价体外释药特征。结果以最佳处方制备的芦丁固体脂质纳米粒呈类球形,平均粒径为195.8±11nm,Zeta电位为-20.65±0.6mV,平均包封率为86.31%,72h体外累积释放87.32%。结论按最佳处方工艺制备的芦丁固体脂质纳米粒具有较高的包封率和较好的缓释效果。     

正交设计优化伊曲康唑固体脂质纳米粒的处方组成与制备工艺

目的:制备伊曲康唑固体脂质纳米粒(itraconazole solid lipid nanoparticles,ITZ-SLNs)并对其进行物相分析以确定纳米粒的形成。方法:以伊曲康唑(ITZ)为模型药物,硬脂酸为载体材料,采用乳化-低温固化法制备伊曲康唑固体脂质纳米粒(ITZ-SLN),正交试验设计优化处方组成和制备工艺,并对纳米粒的结构形态、粒径、表面电位、包封率、体外释药特性等进行了研究。结果:以优化处方制备的伊曲康唑固体脂质纳米粒为类球形实体,粒径分布比较均匀,平均粒径为dav=(118.2±15.00)nm,Zeta电位为-(37.06±0.53)mV,包封率为(92.11±1.60)%,药物体外释放符合Higuchi方程,经DSC分析证明纳米粒确已形成。结论:伊曲康唑固体脂质纳米粒有望成为新型缓释纳米给药系统。     

伊曲康唑固体脂质纳米粒的制备

目的:制备伊曲康唑固体脂质纳米粒,并考察其理化性质.方法:采用乳化-低温固化法制备伊曲康唑固体脂质纳米粒(ITZ-SLN);在脂质、表面活性剂等辅料和主药用量的单因素考察基础上,以包封率为评价指标,采用正交试验设计,优化处方组成和制备工艺;用低温超速离心法测定包封率,透射电镜观察形态,激光粒径分析仪测定粒径和ξ电位.结果:脂质、表面活性剂和主药的用量对ITZ-SLN包封率均有不同程度的影响.以优化处方制备的伊曲康唑固体脂质纳米粒为类球形实体,粒径分布比较均匀,平均粒径为dav=(118.2±15.00)nm,ξ电位(-37.06±0.53)mV,包封率(92.11±1.60)%.结论:乳化-低温固化法制备伊曲康唑固体脂质纳米粒工艺可行.     

人参皂苷Rd固体脂质纳米粒的制备

目的:制备人参皂苷Rd固体脂质纳米粒,并考察其理化性质。方法:从旋转薄膜-超声分散法、乳化蒸发-低温固化法、高剪切乳化超声法和高压乳匀法中优选出制备方法;在脂质、表面活性剂等辅料和主药用量的单因素考察基础上,采用正交试验设计,确定最佳处方组成和制备工艺条件;用凝胶柱色谱和HPLC法测定包封率,透射电镜观察形态,激光粒径分析仪测定粒径和Zeta电位。结果:脂质、表面活性剂、助表面活性剂和主药的用量对Rd固体脂质纳米粒的粒径、Zeta电位和包封率均有不同程度的影响。高压乳匀法适合制备Rd固体脂质纳米粒。纳米粒表面呈圆整的球状,大小相近,分散均匀;平均粒径为(102.7±27.0)nm,Zeta电位为(-44.9±9.5)mV,包封率和载药量分别为(81.8±2.6)%和(6.37±0.21)%(n=3)。纳米粒稳定性良好,在4℃下保存4周后,粒径和包封率变化不明显。结论:高压乳匀法适合制备人参皂苷Rd固体脂质纳米粒,工艺稳定可行。     

青藤碱固体脂质纳米粒的制备

目的：以山嵛酸甘油酯为载体材料制备青藤碱固体脂质纳米粒并评价其质量。方法：采用乳化蒸发一低温固化法制备青藤碱固体脂质纳米粒，以正交设计优化其处方和制备工艺。对其粒径、形态、表面电位、包封率等理化性质进行研究，并考察其稳定性。结果：所制固体脂质纳米粒外观形态圆整，平均粒径为208．7nm，Zeta电位为-38．5mV，平均包封率为65．7％。4℃放置2个月，粒径、包封率无明显变化。结论：青藤碱固体脂质纳米粒的制备，为开发其新制剂奠定了实验基础。     

阿托伐他汀钙纳米粒的制备与质量评价

目的:制备阿托伐他汀钙纳米粒新剂型,对其性质进行研究,优选最佳工艺条件。方法:采用乳化-溶剂挥发法制备阿托伐他汀钙纳米粒溶液,通过对处方优化,以载体材料用量(X₁)、有机溶剂用量(X₂)、表面活性剂用量(X₃)为自变量,利用Box Behnken设计响应面法以纳米粒粒径(Y)为响应值,优化了阿托伐他汀钙纳米粒的处方。用Malvern激光粒度分析仪测定了粒径分布和纳米粒的Zeta电位,扫描电镜分析了其形态,用高速冷冻离心法和紫外分光光度法测定了包封率和载药量。结果:采用乳化-溶剂挥发法制备阿托伐他汀钙纳米粒溶液是适合的。响应面优化最优值为阿托伐他汀钙20 mg、卵磷脂178 mg、乙酸乙酯15 mL、聚山梨酯80774 mg,所制备的阿托伐他汀钙纳米粒呈类球形,其平均粒径(71.99±13.62) nm,Zeta电位为(-31.48±2.46) mV,包封率为(91.27±1.7)%,载药量(9.58±0.22)%。结论:采用乳化-溶剂挥发法制备阿托伐他汀钙纳米粒处方及工艺适合,相关性质检测方法可行。     

马钱子碱固体脂质纳米粒制备及质量评价

目的：以乳化蒸发-低温固化法制备马钱子碱固体脂质纳米粒并评价其质量。方法：在单因素考察的基础上以正交试验设计优化、筛选最佳处方。用透射电镜观察固体脂质纳米粒的形态,HPLC法测定马钱子碱固体脂质纳米粒的包封率,激光散射测定Zeta电位和粒度分布,并考察其稳定性。结果：所制固体脂质纳米粒外观形态圆整,平均粒径为116nm,Zeta电位为-29．98mv,包封率为50．7％,载药量为2．25％。4℃放置1个月,粒径、包封率无明显变化。结论：本研究制备的马钱子碱固体脂质纳米粒粒径分布窄,稳定性好,为开发马钱子碱低毒长效的制剂奠定了实验基础。     

阿克他利固体脂质纳米粒的制备及体外释药特性

目的:制备阿克他利固体脂质纳米粒研究外释药模式。方法:单因素考察的基础上,以正交试验设计优化,筛选最佳处方和制备工艺。透射电镜观察固体脂质纳米粒的形态,激光散射测定Zeta电位和粒度分布,超速离心法测定阿克他利固体脂质纳米粒的包封率,研究体外释放速度。结果:所制固体脂质纳米粒外观形态圆整,粒度分布为50~200nm,平均粒径为120nm。Zeta电位为-17.14mV,包封率为51.20%。体外释药特性研究具有良好的缓释特性,在0~12h符合100Q=38.536t1/4-16.859(r=0.999 0),13~648h符合100Q=13.907t1/4 28.32(r=0.999 2)。结论:通过优化处方和制备工艺,采用乳化蒸发-低温固化法制备阿克他利固体脂质纳米粒,其体外释药具有明显的缓释、长效作用。     

卡莫氟固体脂质纳米粒的制备及工艺研究

目的:制备卡莫氟固体脂质纳米粒并考察其药剂性质。方法:采用高压均质法制备卡莫氟固体脂质纳米粒混悬液,以单因素考察和正交设计法筛选处方和工艺,并考察其形态、粒径、载药量及包封率。结果:优选出的较佳处方大豆卵磷脂、泊洛沙姆188、吐温-80和硬脂酸用量分别为8.0、12.0、1.0、7.5mg·mL-1;所制得的固体脂质纳米粒为圆整的实体粒子,表面光滑,平均粒径为78.7nm,载药量为23.47%,包封率为82.33%。结论:高压均质法可用于卡莫氟类脂溶性药物固体脂质纳米粒的制备。     

蓝萼甲素固体脂质纳米粒的制备及理化性质研究

目的:制备蓝萼甲素固体脂质纳米粒,并对其理化性质进行研究。方法:用乳化-溶剂挥发法制得蓝萼甲素固体脂质纳米粒,并对其粒径、形态、表面电位、包封率、体外释药性质等进行研究。结果:所得蓝萼甲素固体脂质纳米粒的粒径分布均匀,平均粒径为(190±10·3)nm,Zeta电位为—31·2mV,平均包封率为(50·45±0·804)%;药物体外释放符合Higuchi线性方程,具有显著缓释作用。结论:固体脂质纳米粒可作为蓝萼甲素新型缓释给药系统。     

雷公藤内酯醇固体脂质纳米粒的制备及理化性质

目的：以聚乙二醇单硬脂酸酯表面修饰材料结合到固体脂质纳米粒（solid lipid nanoparticles,SLN）,以雷公藤内酯醇（triptolide,TPL）为模型药,制备一种具有良好亲水亲脂性的雷公藤内酯醇固体脂质纳米粒。方法：采用熔融-乳化法制备固体脂质纳米粒。通过单因素考察、中心复合设计（central composite design,CCD）,考察脂质材料、聚山梨醇酯-80和PEG-stearate（PEG-SA）三个因素对TPL-SLN粒径、包封率和载药量的影响。通过透射电镜、热分析和X-射线衍射考察TPL-SLN的理化性质,并考察其固体脂质纳米粒的稳定性以及体外释放情况。用MTT法测定其对人正常肝L02细胞和肝癌细胞HepG2的增殖抑制作用并计算其IC₅₀。结果：最优的处方：脂质材料为7.5%,聚山梨醇酯80（Tween 80）为2%和PEG-SA为2%,其粒径（193.43±6.07）nm,包封率（87.63±0.09）%,载药量（0.33±0.01）%。透射电镜观察所制备的纳米粒的形态近似于球形,DSC分析和X-射线衍射证实TPL以非晶型的形式存在于固体脂质纳米粒中。稳定性考察发现纳米粒粒径在一个月的贮存期基本没有变化（P>0.05）,体外释放表明TPL-SLN具有体外缓释特性。TPL-SLN对肿瘤细胞的抑制作用强于正常肝细胞。结论：雷公藤内酯醇聚乙二醇修饰固体脂质纳米粒有望开发为临床口服用药新剂型。     

Preparation and Evaluation of Quinapyramine Sulphate-Docusate Sodium Ionic Complex Loaded Lipidic Nanoparticles and Its Scale Up Using Geometric Similarity Principle

The objective of the present work is to prepare and evaluate ionically complexed Quinapyramine sulphate (QS) loaded lipid nanoparticles and its scale up using geometric similarity principle. Docusate sodium (DS), at a molar ratio of 1:2 of QS to DS, was used to prepare hydrophobic Quinapyramine sulphate-Docusate sodium (QS-DS) ionic complex. Based on the difference in total solubility parameter and polarity of QS-DS complex and different lipids, precirol was selected as a lipid for the preparation of lipidic nanoparticles. The particle size, zeta potential, and % entrapment efficiency (%EE) of QS-DS ionic complex loaded solid lipid nanoparticles (QS-DS-SLN) was found to be 250.10 ± 26.04 nm, ?27.41 ± 4.18 mV and 81.26 ± 4.67% respectively. FTIR studies confirmed the formation of QS-DS ionic complex. DSC and XRD studies revealed the amorphous nature of QS in QS-DS-SLN. The spherical shape of nanoparticles was confirmed by scanning electron microscopy. QS-DS-SLN showed sustained release of QS for up to 60 h. No significant difference was observed in particle size, zeta potential, and % entrapment efficiency of pilot-scale batch prepared by using rotational speed of 700 rpm. In conclusion, ionic complexation approach can be used to increase % EE of charged drugs into lipid nanoparticles.     

吡喹酮固体脂质纳米粒的制备及其理化性质研究

目的:制备吡喹酮固体脂质纳米粒(PZQ-SLN),并考察其理化性质。方法:以山嵛酸甘油酯和乙酸丁酯为脂质材料,超声分散法制备PZQ-SLN,透射电镜观察纳米粒形态,测定其粒径、Zeta电位和药物包封率,并进行体外释放试验及考察样品的稳定性。结果:所得脂质纳米粒为类圆球状,粒径分布较均匀。样品粒径为(100±21)nm,包封率为(79.3±0.69)%,平均Zeta电位值为—66.3mV。药物体外释放符合Weibull方程。4℃放置3mo后粒径、包封率和Zeta电位均无明显变化。结论:制备的PZQ-SLN理化性质较为理想,能使药物缓慢释放。4℃条件下贮存比较稳定。     

莫匹罗星壳聚糖纳米粒原位凝胶的制备与体外抗菌活性研究

目的：制备莫匹罗星壳聚糖纳米粒（Mupirocin-loaded chitosan nanoparticles,Mup-loaded CNs）原位凝胶,并考察其体外抗菌活性。方法：采用离子凝胶化法制备Mup-loaded CNs,以药物与壳聚糖比例（X₁）、pH值（X₂）、搅拌速度（X₃）作为考察对象,以药物包封率（Y）作为评价指标,运用Box-Behnken实验设计法优化Mup-loaded CNs处方和制备工艺;采用Malvern Zetasizer Nano型激光粒度仪测定其粒径分布和Zeta电位,透射电镜观察微观形态;以泊洛沙姆407作为凝胶基质将Mup-loaded CNs制备成原位凝胶;并比较了莫匹罗星软膏、Mup-loaded CNs以及原位凝胶的体外抗菌活性。结果：优化得到Mup-loaded CNs处方组成及制备工艺为：药物与壳聚糖比例为0.2、pH值为3.5、搅拌速度为350 r·min^-1,Mup-loaded CNs的包封率为（89.5±1.8）%,平均粒径为（217.8±10.5） nm,PdI为（0.158±0.015）,Zeta电位为（24.8±1.8） mV;在透射电镜下可观察到Mup-loaded CNs呈近似呈球形或类球形分布,粒径分布较均匀;Mup-loaded CNs原位凝胶对金黄色葡萄球菌、大肠杆菌均有较好的抗菌效果。结论：Mup-loaded CNs原位凝胶处方设计合理,制备工艺简单,具有良好的物理性能和抗菌活性,有望成为Mup外用给药的一种新途径。     

Formulation and in vitro characterization of domperidone loaded solid lipid nanoparticles and nanostructured lipid carriers

Background and the purpose of the study

Domperidone (DOM) is a dopamine- receptor (D₂) antagonist, widely used in the treatment of motion-sickness. The pharmacokinetic parameters of DOM make it a suitable candidate for development of Solid Lipid Nanoparticle (SLN) and Nanostructured Lipide Carrier (NLC). The purpose of the present investigation was to prepare and evaluate DOM loaded solid lipid nanoparticles (DOM-SLN) and DOM loaded nanostructured lipid carriers (DOM-NLC).

Methods

DOM loaded SLN and NLC were prepared by hot homogenization followed by ultrasonication technique, using trimyristin as solid lipid, cetyl recinoleate as liquid lipid and a mixture of soy phosphatidylcholine (99%) and tween 80 as surfactant. SLN and NLC were characterized for particle size, polydispersity index (PDI), zeta potential and entrapment efficiency. The effects of composition of lipid materials and surfactant mixture on the particle size, PDI, zeta potential, drug entrapment efficiency, and in vitro drug release behavior were investigated. DSC analysis was performed to characterize the state of drug and lipid modification. Shape and surface morphology were determined by transmission electron microscopy (TEM). SLN and NLC formulations were subjected to stability study over a period of 40 days.

Results

The mean particle size, PDI, zeta potential and entrapment efficiency of optimized SLN (SLN1) and NLC were found to be 30.45 nm, 0.156, 12.40 mV, 87.84% and 32.23 nm, 0.160, 10.47 mV, 90.49% respectively. DSC studies revealed that DOM was in an amorphous state and triglycerides were in the β prime form in SLN and NLC. Shape and surface morphology was determined by TEM revealed fairly spherical shape of nanoparticles. In vitro release studies demonstrated that both the SLN and NLC formulations possessed a controlled release over a period of 24 hrs. SLN and NLC formulations were subjected to stability over a period of 40 days. There was no significant (P<0.05) change in particle size, zeta potential, PDI and entrapment efficiency indicating the developed SLN and NLC were fairly stable.

Conclusion

Fairly spherical shaped, stable and controlled release DOM-SLN and DOM-NLC could be prepared by hot homogenization followed by ultrasonication technique.